HeltecBMS 73B

Contents

Heltec 73B Battery Spot Welding Pen User Manual

Model: 73B | Brand: HeltecBMS

1. Introduction

Thank you for choosing the Heltec 73B Battery Spot Welding Pen. This manual provides essential information for the safe and efficient operation of your device. Please read it carefully before use and keep it for future reference.

The Heltec 73B is an advanced spot welding pen designed for precision and efficiency in battery pack assembly and repair. It features an adjustable instantaneous welding mechanism, low resistance for superior conductivity, and a robust design for safety and durability.

Product Features

  • Adjustable Instantaneous Welding: Welds with slight push pressure, eliminating the need for complicated external foot pedal switches.
  • Fast Heat Dissipation: Designed to support high current welding.
  • Low Resistance, Good Conductivity: Features an ultra-low resistance of 0.747mΩ, significantly improving welding efficiency and stability.
  • Safety Indicator: Equipped with two color lights for welding safety indication.
  • Cable Options: Available with 16 or 25 square copper wires.
  • Wide Compatibility: Compatible with Heltec HT-SW01D/SW01H/SW02A/SW02H spot welders and suitable for 18650, 21700, 32700 battery packs.
Video: Heltec 73B Spot Welding Pen Product Overview and Demonstration.

2. Safety Information and Attentions

WARNING: Failure to follow these safety instructions may result in fire, electric shock, or other injury or damage.

  1. Power inside the capacitor has been released for safe transportation before leaving the factory. When you receive the machine, please turn it on, charge it for 20-30 minutes, and wait for the voltage to rise between 5.2~5.8V before spot welding.
  2. Use the official HeltecBMS adapter to work with the welding machine. An adapter from a third-party supplier will damage the device.
  3. Always wear appropriate safety glasses and gloves during the welding process.
  4. Removing the oxidation layer on welding pins is crucial for optimal energy transfer and welding performance.
  5. Unplug the machine from the power source when it is not in use.
  6. The welding current displayed instantaneously is a pulse release; ordinary testing instruments cannot accurately measure it.
  7. Ensure welding materials are clean before welding. Remove any oil stains or oxide layers from the surface to avoid poor welding.
  8. Keep the device out of reach of children.
  9. Unauthorized disassembly of the machine is strictly prohibited and unsafe.
  10. Do not use the product in flammable, explosive, or water-spray environments.

3. Setup and Installation

3.1. Power Supply and Mobile Welding Pen Installation

  1. Connect Power: Plug the power output plug into the spot welder's power connection port.
  2. Charge: Plug the adapter into an AC 100-240V wall socket to charge the machine.
  3. Install Welding Pen: Insert the mobile welding pen into its corresponding socket, ensuring a solid connection.
Heltec Battery Spot Welding Pen with accessories
Image: Heltec Battery Spot Welding Pen with included accessories.
Heltec Battery Spot Welding Pen with accessories
Image: Heltec Battery Spot Welding Pen with accessories, including hex keys and screwdriver.

3.2. Main Machine and Base Display (if applicable)

If using with a base, ensure the welder's back is inserted vertically into the base to prevent movement during the welding process.

Welding pen connected to a spot welder machine
Image: The welding pen connected to a spot welder machine, demonstrating compatibility with U-size and Circle-size ports.

3.3. Adjustable Welding Needle Distance

The distance between the welding needles can be adjusted to suit various battery sizes and welding needs. Use the provided tool to adjust the level of the welding pin.

Adjustable welding needle distance
Image: Illustration of adjustable welding needle distance, from 3mm to 7mm.

4. Operating Instructions

4.1. Introduction to the LED Display

The LED display shows important parameters during operation:

  • Battery pack voltage meter: Displays the current voltage of the battery pack.
  • Capacitor Energy Storage Precision Welding Machine: Indicates the status of the capacitor.
  • CH-ms: Appears when the machine is charging.
  • 25t ms: Indicates the energy release (25t). The release energy grade for AT mode can be adjusted from 00 to 99.

4.2. Charging and Initial Voltage Check

  1. Initial Power-On: After connecting the power, the LED will show "CH" intermittently, indicating the real-time voltage value of the internal capacitor.
  2. Ready for Use: Wait until the voltage is between 5.2V and 5.8V. The machine will then display "25ms" (or similar), indicating it is ready for use.
  3. Voltage Test: Connect the voltage test line to the battery to display its voltage.

4.3. Spot Welding Operation Steps (AT Mode)

AT mode (automatic welding) is suitable for welding a large number of batteries as it does not require foot pedal control.

  1. Start-up: The device defaults to AT mode upon starting.
  2. Positioning: Hold the welding pen and apply a certain pressure to the object's surface (e.g., nickel strip).
  3. Automatic Welding: Automatic welding begins after approximately 20ms of contact.
  4. Inspection: Check the reliability of the weld spots.
Spot welding pen in use
Image: Spot welding pen in action, demonstrating welding on a battery pack.

4.4. Adjusting Welding Pressure

The welding pressure can be adjusted by twisting the knob on the pen. This allows for control over the welding force, making it suitable for different material thicknesses.

Adjustable welding pressure knob
Image: Close-up of the welding pen showing the adjustable pressure knob.

5. Maintenance

  • Welding Pin Care: Regularly remove any oxidation layer from the welding pins using a grinder to ensure good energy transfer and consistent welds.
  • Cleaning Materials: Always clean welding materials thoroughly before welding to remove oil stains or oxide layers.
  • Storage: Unplug the machine from the power source when not in use. Store in a dry, safe place away from children.
  • Removable Welding Needles: The welding needles are removable and replaceable. This allows for easy maintenance and cost-effective recycling of needles.
  • Prevent Short Circuits: Always keep the two welding pins separate to prevent short circuits.

6. Troubleshooting

Error TypeIssueSolution
Panel display "E01"Welding pins in contact with each other?Keep welding pins separate and ensure welding pen copper wires are separate.
Oxidation of welding pinsUse a grinder to remove the oxidation layer.
Weak spotsVoltage under 5.2V?Charge the machine to between 5.2-5.8V or higher.
No energy releaseAdapter not from HeltecBMS?Use the official HeltecBMS adapter.

7. Specifications

General Parameters

ParameterValueParameterValue
ModelHT-SW01A+Voltage Output5~5.8V (Peak)
Voltage InputAC 100-240V 50/60HZPeak Welding Energy119J
Pulse Power11.6KW (Peak)Trigger ModeAT
Energy Grade0-99TWelding ModeRocker arm press down spot welding, Mobile pen spot welding
Pulse Time0~10mSPreload Delay20~50mS
Adapter Parameter15V2A (Peak)Charging Time20~30min
Dimension67(L)x176(W)x126(H)mmWeight2KG
Measuring range0-199V

Welding Head Parameters (73SA)

ParameterValueParameterValue
Handle Torque950gHandle Operation Angle0-50°
Welding Arm Operating Distance15mmPressure Adjustment Range1~9.5N
Peak Welding Energy119JWelding Arm Width44mm

Spot Welding Thickness Reference Table

Thickness0.1mm0.12mm0.15mm0.2mm0.3mm
Pure nickel06-08t10-11t12-15t20-25t60-70t
Nickel plated steel03-04t07-08t10-12t15-18t40-50t

Please choose the proper energy grade and pulse current according to different object materials and thicknesses.

Welding various materials
Image: Examples of various materials that can be welded, including aluminum nickel strip, nickel strip, and circuit boards.
Resistance comparison of welding pens
Image: Comparison showing the low resistance (0.747mΩ) of the 73B welding pen versus other welding pens (1.455mΩ).

8. User Tips

  • The two spot pins move independently with spring tension, allowing them to conform better to uneven surfaces.
  • A strong weld will often leave some weld material on the pen when pulled away, which is a good indicator of a successful weld.
  • The 25 gauge wires are designed to be flexible and not stiff, aiding in maneuverability during welding.
  • For consistent welds, especially with thicker materials, ensure adequate pressure is applied. If the springs feel too weak, adjust the pressure knob to its maximum setting or ensure proper technique.

9. Frequently Asked Questions (FAQ)

Q: Is this pen compatible with the Awithz UF 20B device?
A: This welding pen is compatible if your purchased equipment is equipped with an O‑type 25 mm² welding‑pen socket.

10. Warranty and Support

HeltecBMS is committed to providing stable and high-quality Battery Management System products. For support or inquiries, please contact us:

  • Website: www.Heltec-BMS.com
  • E-mail: echo@heltec.cn
  • Telephone: 18123313360
  • Address: 64th ChengHong road, Chenghua Section, Chengdu, Sichuan, China

HeltecBMS reserves the right to upgrade the machine and modify this manual without prior notice. We appreciate your understanding.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.