1. Introduction
The Rakoncnc 6090 Mini CNC Wood Router is a versatile machine designed for engraving and carving various materials including MDF, PVC, metal, and aluminum. This manual covers critical safety information, operational procedures, and maintenance guidelines to ensure optimal performance and longevity of your machine.
2. Safety Precautions
Hazard: Mechanical Injury
- Never touch the cutting tool with your hands while the spindle is rotating.
- No part of your body may enter the work area while the machine is running.
- Protective covers or safety light curtains must be installed and must not be removed.
- Long hair must be tied up. Never wear gloves while operating rotating equipment.
Warning: Fire Risk
- Wood chips and dust are flammable. Smoking is strictly prohibited in the work area.
- Fire extinguishers must be available (carbon dioxide or dry powder recommended).
- Clean the dust collection box daily. Do not leave it overnight.
- Do not leave the machine while the spindle is cutting at high speed.
Other Hazards
- Equipment must be reliably grounded.
- The spindle and drive are high-voltage components. Unauthorized personnel must not open the electrical control box.
- The dust collection hose must not be entangled in moving parts.
- Workpieces must be reliably fixed. Processing without securing the workpiece is strictly prohibited.
3. Equipment Components
- Bed: Cast iron/steel gantry frame
- Spindle: Air-cooled/Water-cooled spindle motor
- Control System: Handle/Computer control card + driver (e.g., Weihong/Baoyuan/Xindai)
- Transmission System: Lead screw/rack + guide rail
- Accessories: Cutting tools, tool setter, clamping fixture, dust hood
4. Setup
4.1. Power-On Procedure
- Confirm emergency stop button is pressed.
- Turn on the main power switch.
- Release the emergency stop button.
- Turn on the control computer/handheld.
- Open the control software.
- Reset any alarms.
- Start the spindle cooling system (water chiller).
- Start the vacuum cleaner.
- Startup is complete.
4.2. Workpiece Clamping Principles
- Sheet metal must be clamped on all four sides or secured with vacuum-adhesive.
- Temporary fixing with nails or double-sided tape is strictly prohibited.
- Lightweight, thin sheets must be protected from vibration during cutting.
4.3. Tool Installation
- Clean the tool holder and spindle collet, ensuring they are free of oil and wood chips.
- Tool Extension Length: The tool should penetrate the workpiece + 3~5mm. Excessive extension may cause tool breakage.
- Tighten the Locking Nut: Apply force with a wrench until locked. Never start the machine without tightening.
- Manually rotate the spindle to check for tool eccentricity and ensure it is not hitting the workpiece.
4.4. Tool Setting (Setting the Workpiece Zero Point)
Recommended Method: Automatic Tool Setter
- Place the tool setting block on the workpiece surface.
- Execute the "Automatic Tool Setting" command in the control software.
- The system automatically records the Z-axis zero point.
Manual Tool Setting
- X/Y Zero Point: Align the tool tip with the lower left edge of the workpiece.
- Z Zero Point: Using a feeler gauge/tool setting block, lift the tool 0.1~0.2mm after it contacts the surface.
- Zeroing: Set the current position as the workpiece coordinate in the software.
5. Operating Instructions
5.1. Program Loading
- Generate toolpaths using compatible software such as ArtCAM, AlphaCAM, Jingdiao, or Wentai.
- Post-process the toolpaths into machine tool recognition formats (.nc/.cnc/.u00/.tap, etc.).
- Transfer the program to the controller via USB flash drive or network.
- Dry Run Verification: Raise the Z-axis by 30mm, simulate the operation, and confirm no collisions before actual machining.
5.2. Start Machining
- Close the safety door.
- Reconfirm the vacuum is on.
- Press "Cycle Start".
- Pay close attention to the first cut: Observe the cutting sound and whether chip removal is normal.
- If any abnormal noise, smoke, or displacement occurs, immediately press the emergency stop button.
6. Maintenance
6.1. Shutdown Procedure
- Stop the machining program.
- Raise the tool to a safe height.
- Shut down the spindle.
- Exit the control software.
- Turn off the computer/handheld.
- Press the emergency stop button.
- Turn off the main power switch.
- Clean the worktable and dust collection box.
- Apply guide rail oil.
6.2. Weekly Maintenance
- Clean rack and pinion; apply lithium grease.
- Check spindle cooling system (water level/air filter).
- Inspect all bolts and fasteners for looseness.
- Test all axis movements for abnormal noise.
- Clean dust collector filter.
6.3. Monthly Maintenance
- Replace cooling water (water-cooled spindle).
- Clean or replace spindle air filter (air-cooled).
- Check drive belt tension.
- Inspect electrical cabinet cooling fan.
- Verify machine leveling.
6.4. Quarterly Maintenance
- Deep clean electrical cabinet with dry compressed air (power off).
- Check all limit switches and sensors.
- Inspect ball screw nuts for backlash.
- Test ground continuity.
- Professional inspection of spindle bearings.
7. Prohibited Operations
- NEVER change tools while the spindle is rotating.
- NEVER reach into the work area during machine operation.
- NEVER wear gloves while operating.
- NEVER run the machine with safety guards removed.
- NEVER start a water-cooled spindle without coolant.
- NEVER machine unsecured workpieces.
- NEVER use compressed air to blow down the machine table (dust hazard).
- NEVER leave the machine unattended overnight (essential woodworking rule).
- NEVER modify system parameters without authorization.
8. Specifications
| Feature | Specification |
|---|---|
| Model | RCM6090 |
| Engraving Area | other (specific working area 600x900mm) |
| Working Area | 600x900mm |
| Z-axis Working Size | 200mm standard (customization optional) |
| Spindle Motor | 3kw or bigger (0 - 24000rpm) water cooling spindle |
| Rotating Speed of Spindle | 24000rpm |
| Working Mode | Stepper motor (servo is optional) |
| Motor | Stepper motor |
| Controller | MACH3 |
| Control System | Nc studio controller, parallel interface |
| Drive Mechanism | Rack and pinion on X,Y axis, Z axis ball screw transmission |
| Rail Guide | Square |
| Transmit | X Y Z ball screw |
| Table Surface | T-slot table (vacuum table optional) |
| Frame | Seamless welded steel structure |
| Motion Positioning Accuracy | ± 0.03/300mm |
| Repositioning Accuracy | ± 0.05mm |
| Max Motion Speed | 30,000mm/min |
| Max Engraving Speed | 25,000mm/min |
| Z-axis Setting | Auto Z origin tool sensor |
| Dictate Format | G code, *.u00, *.mmg, *.plt |
| Operating Voltage | 220V/ 380V |
| Software | Type3, ArtCAM software |
| Lubrication System | Oil lubrication system |
| Gross Weight | 350kg |
| Is Smart Device | Yes |
| Origin | Mainland China |
| Certification | CE |
| Condition | New |
9. Applications and Materials
Wide Range of Applications:
- Wood Furniture Industry: Wave plates, fine patterns, antique furniture, wooden doors, screens, craft sashes, composite gates, cupboard doors, interior doors, sofa legs, headboards, game cabinets, computer tables, sewing machine tables, instruments, etc.
- Advertising Industry: Advertising identification, sign making, acrylic engraving and cutting, crystal word making, blaster molding, and other advertising material derivatives.
- Crafts: Engraving characters of any language and patterns on gifts and souvenirs, primitive processing and shaping of artistic crafts, and stiletto work.
- Molding: Engraving delicate letters and flower patterns, primitive and fine processing of small molds.
- Architectural Models: Engraving fine window, fencing, and wall patterns, etc.
Suitable Materials:
- Acrylic sheet
- ABS double color sheet
- PVC foam sheet
- Wooden sheet
- PCB
- Aluminum
- Brass
- Steel
- MDF
10. Troubleshooting
Common Errors and Solutions:
- Tool Collision (Forgetting to Lift Tool): Always ensure the tool is lifted to a safe height after tool setting and before starting machining to prevent collisions.
- Cutting Through Worktable (Forgetting Material Thickness Difference): Account for the shim height and material thickness accurately during Z-axis zeroing to avoid cutting into the worktable.
- Abnormal Noise, Smoke, or Displacement during Machining: Immediately press the emergency stop button. Investigate the cause, which could include loose fasteners, incorrect tool settings, or material issues.
11. User Tips
- Initial Setup: Pay close attention to the initial settings of the control system. If you encounter issues, review the manual or contact support for guidance.
- Spindle Speed: The spindle operates at 24,000 RPM. Ensure your VFD, water pump, and hoses are correctly installed and functioning to support this.
- Material Securing: Always double-check that your workpiece is securely clamped to prevent movement and ensure precise cuts.
- Regular Cleaning: Consistent cleaning of the dust collection box and machine components will prevent buildup and maintain machine performance.
12. Warranty and Support
The machine and spindle come with a 1-year warranty. For detailed instructions, operation videos, or technical guidance, please contact Rakoncnc support.
Contact Information:
- Website: https://www.rakoncnc.com
- Email: Info@rakoncnc.com
Rakoncnc offers free technical advice by qualified mechanical engineers and can provide technical guidance in your country if needed.