SONGGER TA640A, TA641A, TA641B, TA642A, TA642B, TA642C

Contents

Handheld Digital Anemometer User Manual

Models: TA640A, TA641A, TA641B, TA642A, TA642B, TA642C

Brand: SONGGER

1. Introduction

This handheld digital anemometer is a high-precision air velocity measuring instrument designed for various applications including HVAC inspection, ventilation testing, environmental monitoring, and industrial airflow diagnostics. Depending on the model, it supports measurements of wind speed, air temperature, air volume, and humidity. Advanced models offer features such as data logging, audible and visual alarms, and USB communication for PC data analysis. Both integrated and split probe designs are available to suit different measurement scenarios.

SONGGER Handheld Digital Anemometer, showing main features like wind speed, temperature, humidity, air volume, USB communication, and data storage.
Figure 1: Overview of the Handheld Digital Anemometer (TA640A/TA641A/TA642A series).

2. Safety Information

Precautions

  • Do not use the instrument in explosive or flammable environments.
  • Avoid exposing the sensor to strong impacts or high-speed debris.
  • Do not immerse the device in water or use it in heavy condensation.
  • Ensure correct battery polarity during installation.
  • Remove batteries if the instrument will not be used for an extended period.
  • Do not exceed the specified measurement range to prevent sensor damage.

Warning Information (EU Market Reference)

WARNING!

  • This product contains rotating sensor components. Avoid contact during operation.
  • Use only the specified battery types and power supply.
  • Do not disassemble or modify the instrument.
  • Keep out of reach of children.
  • Electronic waste disposal must follow the WEEE Directive and local EU regulations.

Note: The above warning information is for reference only. Final warning language must comply with the official language requirements of the destination EU country.

3. Product Overview

The anemometer features a robust design with an 8-blade fan for accurate and responsive measurements. The display is a high-definition LCD, providing clear readings.

Key Components and Controls

Close-up of the 8-blade fan design on the anemometer.
Figure 2: The 8-blade fan design, combined with low-friction high-precision bearings, delivers responsive performance.
High-definition large screen display of the anemometer showing wind speed, units, and temperature.
Figure 3: High-definition large screen display with white backlight. Display size: 34 x 31mm (TA640A), 37 x 41mm (TA641 series), 53 x 44mm (TA642 series).

Model TA640A

Diagram of TA640A integrated type anemometer with dimensions and basic specifications.
Figure 4: TA640A Integrated Type. Power: 2×1.5V AAA. Wind Speed: 0.1-30 m/s. Temp: 0-45°C. Features Max/Min/Data Hold. Dimensions: 168mm x 59mm x 29mm.
Labeled diagram of TA640A showing fan blade, display screen, backlight, unit switch, data hold, max/min value, power on/off.
Figure 5: TA640A Product Information with labeled components.

Model TA641B

Labeled diagram of TA641B showing fan blade, display screen, high limit alarm, data hold, unit switch, max/min/avg value, power on/off, low limit alarm.
Figure 6: TA641B Product Information with labeled components. Dimensions: 152mm x 55mm.

Models TA642A/B

Labeled diagram of TA642A/B showing high-sensitivity fan, alarm indicator light, display screen, unit switch, power switch, menu, data hold, data recording, wind speed/air volume, max/min value.
Figure 7: TA642A/B Product Information with labeled components. Dimensions: 239mm x 70mm x 35mm.

Model TA642C (Split Type)

Diagram of TA642C split type anemometer showing the main unit and the detachable probe with telescopic rod and cable, including dimensions.
Figure 8: TA642C Split Type. Features a retractable handle design with a 1m telescopic rod and 1m cable, totaling 2m in length. Dimensions: 175mm x 70mm x 35mm (main unit).

4. Specifications

The following tables detail the technical parameters for each model:

General Specifications

SpecificationTA640ATA641ATA641BTA642ATA642BTA642C
Wind Speed Measurement Range0.1-30.0 m/s0.06-30.0 m/s0.06-45.0 m/s
Wind Speed Accuracy±(2% + 0.2)±0.2 + (±2% of reading)±(2% + 0.2)
Wind Speed Resolution0.1 m/s0.01 / 0.1 / 1
Air Temperature Range0-45℃0-45℃ (32.0-113.0℉)
Air Temperature Accuracy±2℃±2℃ (±3.6℉)
Air Temperature Resolution—0.1 / 1
Humidity Measurement Range—0~99% RH—
Humidity Accuracy—±8% RH—
Wind Speed Display4-digit display, up to 9999
Sensor TypeInfrared laser beam cutting method
Sampling Rate2 times/second
Repeatability—±2%
Data Storage—1000 records
USB PC Communication—✔
Auto Power-Off15 minutes (manually switchable)10 minutes (manually switchable)15 minutes (manual shutdown available)
Operating Environment-10~50℃, Max 80% RH, indoor altitude < 2000 m
Storage Environment-10~50℃, Max 70% RH (remove battery)
Product Dimensions168×59×29 mm152×55×33 mm239×70×35 mm175×70×35 mm
Display Size34×31 mm37×41 mm53×44 mm
WeightApprox. 120 g (excluding battery)Approx. 135 g (excluding battery)Approx. 210 g (excluding battery)
Power Supply2 × 1.5V AAA (R03/LR03)3 × 1.5V AAA (R03/LR03)3 × 1.5V AA (LR06) batteries / USB micro port 5V

Wind Speed Range Details

UnitRange (TA640A)Range (TA641A/B)Range (TA642A/B/C)ResolutionAccuracy
m/s0.1 ~ 30.00.06 ~ 30.00.06 ~ 45.00.1 / 0.01 / 0.001±(2% + 0.2)
km/h1.0 ~ 108.01.0 ~ 108.01.0 ~ 162.00.1 / 0.01 / 0.001±(2% + 0.7)
ft/m10 ~ 590510 ~ 590510 ~ 88581 / 0.1 / 0.001±(2% + 20)
mile/h0.1 ~ 67.000.1 ~ 67.000.1 ~ 100.60.01 / 0.001±(2% + 0.2)
knots0.1 ~ 58.320.1 ~ 58.320.1 ~ 84.480.01 / 0.001±(2% + 0.2)
Bft0 ~ 12——

Conversion factors: 1m/s = 3.6km/h = 196.85ft/min = 3.280ft/s = 2.237mile/h = 1.944knots. 1knot = 0.7234710361 (Bft).

Wind Temperature Range Details

UnitRangeResolutionAccuracy
℃0 ~ 45℃0.1℃±2℃
℉32.0 ~ 113.0℉0.1℉±3.6℉

Air Volume Range Details (TA642A/B/C)

UnitRangeResolutionAccuracy
CFM0 ~ 9999ft³/min0.001 ~ 100—
CMM0 ~ 9999m³/min0.001 ~ 100—
CMS0 ~ 9999m³/s0.001 ~ 100—
Technical parameter table for TA641A and TA641B models.
Figure 9: Detailed Technical Parameters for TA641A and TA641B.
Technical parameter table for TA642A, TA642B, and TA642C models.
Figure 10: Detailed Technical Parameters for TA642A, TA642B, and TA642C.

5. Setup

Battery Installation

Install the correct type and number of batteries according to your model (refer to the specifications table for details). Ensure correct battery polarity during installation.

  • TA640A: 2 × 1.5V AAA batteries
  • TA641A / TA641B: 3 × 1.5V AAA batteries
  • TA642A / TA642B / TA642C: 3 × 1.5V AA batteries
Battery compartment of the anemometer showing two AAA batteries installed.
Figure 11: Battery installation for models using AAA batteries.
Battery compartment of the anemometer showing three AA batteries installed, and a micro USB port for external power.
Figure 12: Dual Power Supply Modes for TA642 series, showing AA batteries and micro USB port.

Power On

Power on the instrument using the power key. Ensure the sensor impeller rotates freely without obstruction before use.

Probe Connection (TA642C Split Type)

For the TA642C split-type model, connect the detachable probe using the 5-pin aviation connector. Extend the telescopic rod as required for measurement, up to 1 meter.

Close-up of the detachable probe with a 5-pin aviation connector.
Figure 13: Detachable probe with 5-pin aviation connector for stable signal transmission.
Hand holding the anemometer probe with the telescopic rod extended.
Figure 14: Telescopic rod extendable design, up to 1 meter.

6. Operation

Measurement Modes and Unit Selection

Select the desired measurement mode (wind speed, air temperature, air volume, or humidity) using the appropriate buttons on the device. Choose the required wind speed unit (m/s, km/h, ft/m, mile/h, knots) using the "UNIT" button.

Anemometer display showing wind speed in m/s with unit selection buttons.
Figure 15: Five wind speed units are switchable by pressing the "UNIT" button.
Anemometer displaying wind speed and temperature readings.
Figure 16: Multiple measurement functions with switchable measurement units for wind speed and temperature.
Anemometer displaying wind speed and temperature readings in a car vent.
Figure 17: Wind Speed / Wind Temperature measurement range: 0.1 ~ 30.0m/s; Accuracy: ±(2%+0.2). Wind temperature measurement range: 0.0 ~ 45.0℃; Accuracy: ±2℃.
TA642C split-type anemometer in use, measuring air flow with its extended probe.
Figure 18: Split-Type Measurement with telescopic handle design and 1m extendable rod and 1m cable, total length 2m.

Data Reading and Hold Function

Read real-time values directly from the LCD. Use the data hold function to freeze readings. Supported models allow viewing of maximum, minimum, and average values.

Anemometer displaying a data hold function, showing locked values.
Figure 19: Data Hold Function can lock maximum, minimum, average, and real-time values during measurement.

Alarms (TA641A/B, TA642 series)

For models with alarms, upper and lower limit thresholds can be set. When the measured value exceeds or falls below the threshold, a buzzer will sound and the warning light will flash.

Anemometer display showing an upper/lower limit exceeding alert with warning light and sound alert icons.
Figure 20: Upper / Lower Limit Exceeding Alert with warning light and sound alert.

Data Logging and USB Communication (TA642B/C)

The TA642 series supports data logging, storing up to 1000 records. These records can be viewed directly on the device. For TA642B/C models, stored data can be transferred to a PC via USB. Upper computer software (compatible with Windows 7, Windows 8, and Windows 10) allows for real-time communication, data download, and the export/printing of xlsx data tables and graphs.

Anemometer display showing multiple data points for wind speed and temperature, indicating data logging.
Figure 21: Data Logging feature for TA642B/C models, capable of storing up to 1000 sets of data.
Anemometer connected to a laptop via USB, showing data being displayed and graphed on the computer screen.
Figure 22: USB PC Communication for TA642B/C models, supporting data download and real-time analysis.

Auto Power-Off

The device automatically shuts off after 10 or 15 minutes of inactivity, depending on the model. This feature can be manually deactivated.

7. Maintenance

Cleaning

Clean the housing and sensor gently with a soft dry cloth. Do not use solvents or abrasive cleaners.

Storage

Store the instrument in a dry, well-ventilated place within the specified storage conditions (-10 to 50°C, maximum relative humidity of 70%). Periodically check battery condition and replace when necessary. Ensure the impeller remains clean and free of dust. Remove batteries during long-term storage.

8. Troubleshooting

If the device is not functioning as expected, please ensure:

  • Batteries are correctly installed and have sufficient charge.
  • The sensor impeller is free from obstructions and rotates smoothly.
  • The device is used within its specified operating environment.
  • For split-type models, the probe is securely connected.

If issues persist after checking these points, please refer to the contact information in the Support section.

9. User Tips

  • Switching Units: Easily toggle between wind speed units (m/s, km/h, ft/min, mile/h, knots) by pressing the "UNIT" button for quick adaptation to different measurement standards.
  • Capturing Peak/Trough Data: Utilize the "MAX/MIN" button during measurements to record and review the highest, lowest, and average values, which is useful for analyzing fluctuating conditions.
  • PC Data Analysis (TA642B/C): For detailed analysis, connect your TA642B/C model to a PC via USB. The accompanying software allows you to export data in .xlsx format and visualize trends with real-time graphs, making reporting and long-term monitoring more efficient.

10. Support & Compliance

Compliance Disclaimer

This document is provided for product instruction purposes only. It does not constitute legal or regulatory advice. The seller is responsible for ensuring full compliance with applicable EU directives and local market regulations.

Contact Information

For technical consultations or bulk orders, please contact us:

  • WhatsApp: +86 13311678550
  • Email: miazhao008@gmali.com
Contact information with WhatsApp number and email address.
Figure 23: Contact details for support.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.