Suetlcoity OC03640

Contents

User Manual

Product: Front Bumper Fog Lamp Grille Air Vent Cover Trim

Model: OC03640

Brand: Suetlcoity

For Toyota Land Cruiser 250 Prado LC250 2024-2025

1. Product Overview

This car decoration accessory is designed to enhance your vehicle's aesthetic appeal while protecting vulnerable surfaces from scratches, dust, and minor impacts. The product features high-quality 3M adhesive tape for secure, long-lasting installation without damaging your car's original finish.

Installed front bumper fog lamp grille air vent cover trim on a white Toyota Land Cruiser 250 Prado LC250
Figure 1: Front Bumper Fog Lamp Grille Air Vent Cover Trim installed on vehicle.

2. Specifications

FeatureDetail
Item TypeChromium Styling
MaterialABS
Color OptionsGlossy Black, Matte Black
Special FeaturesDecoration
External Testing CertificationISO9001
Model Year2024
FitmentFor Toyota Prado 2024
Installation MethodAutomotive adhesive tape (3M)
Item Length22 cm
Item Width12 cm
Item Height3.5 cm
Item Weight220 g
Comparison of Glossy black and Matte black trim pieces
Figure 2: Available color options: Glossy Black and Matte Black.

3. Setup (Installation Instructions)

3.1 Preparation (Critical for Strong Adhesion)

Note: Proper surface preparation ensures maximum bonding strength of 3M tape.

  1. Choose a clean, dry, and well-ventilated area (avoid direct sunlight or humid environments).
  2. Clean the target surface with the provided alcohol wipe (or 50-70% isopropyl alcohol solution) to remove dust, grease, and fingerprints.
  3. Allow the surface to air-dry completely (1-2 minutes, no wiping after cleaning).
  4. Ensure the installation temperature is between 15°C-35°C (59°F-95°F) – low temperatures reduce adhesive effectiveness.

3.2 Step-by-Step Installation

  1. Peel off the red protective film from the 3M tape (avoid touching the adhesive surface with bare fingers).
  2. Align the accessory with your desired position.
  3. Press firmly on the entire surface of the accessory for 30 seconds – apply a minimum pressure of 15 lbs (6.8 kg) to activate the adhesive.
  4. Do not move or remove the accessory within 24 hours – this allows the adhesive to fully cure for permanent bonding.
Hand applying the trim piece to the car's front bumper
Figure 3: Demonstrating the application of the trim piece.
Back of the trim pieces showing the red protective film on the 3M adhesive tape
Figure 4: Rear view of the trim pieces with adhesive tape.
Before and after installation comparison showing improved protection
Figure 5: Installation comparison: Before (vulnerable) vs. After (protected).

4. Operating (Functions & Benefits)

4.1 Decoration Function

  • Enhances vehicle appearance with stylish design.
  • Customizes your car to reflect personal taste without permanent modifications.

4.2 Protection Function

  • Shields car surfaces from scratches, scuffs, and minor collisions.
  • Prevents dust accumulation and simplifies cleaning (wipe with a damp cloth).
  • No tools, no drilling, removable without residue.
Diagram showing high quality material, fade resistance, and corrosion resistance
Figure 6: Product features: High Quality Material, Do Not Fade, Corrosion Resistance.

5. Maintenance & Care

  1. Clean the accessory with a soft, damp cloth – avoid abrasive cleaners or solvents.
  2. Check the adhesion monthly; reapply pressure if edges lift (clean the surface first if needed).
  3. For removal: Use 3M adhesive remover or heat the tape gently with a hair dryer (low heat) to soften the bond, then peel off slowly.

6. Troubleshooting

Problem Solutions

  • Accessory falls off: 1. Recheck surface cleanliness; 2. Ensure installation temperature is adequate; 3. Apply more pressure during installation.
  • Adhesive residue left: Wipe with alcohol or 3M adhesive remover.
  • Misalignment after installation: Remove within 5 minutes (before adhesive cures) and reposition; after 24 hours, follow removal instructions first.

7. Safety Warnings

Warning!

  1. Do not install on airbag deployment areas (e.g., steering wheel, door panels near airbags) – may interfere with safety systems.
  2. Avoid blocking driver's view (e.g., front windshield, rearview mirrors) – violates traffic safety regulations.
  3. Keep away from children under 36 months – small parts may pose choking hazards.
  4. Do not use near open flames or high-temperature sources (adhesive may weaken above 60°C).

8. User Tips

  • Ensure the surface is thoroughly cleaned and dry before application for optimal adhesion.
  • Apply firm, even pressure across the entire surface of the trim piece during installation to activate the adhesive properly.
  • Allow the adhesive to cure for the full 24 hours without disturbance for a permanent bond.
  • Users have noted the good quality of materials and craftsmanship, ensuring a durable and aesthetically pleasing upgrade.

9. Warranty & Support

Warranty Information

Warranty Period: 12 months from purchase date (covers manufacturing defects, not improper use).

Contact Us

  • AliExpress Store Link: Tayshow-Auto Store
  • Customer Service Email: 669279713@qq.com
  • Service Hours: 9:00 AM - 6:00 PM (GMT+8), Monday to Friday

For the latest version of this manual, please visit our store.

A PDF version of this manual is available for download: User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.