Cybervelo EK7 E-Bike Instruction Manual

1. Safety Guidelines

⚠️ Please mind potential fire risk and strictly follow the instruction manual for charging and storage. While using the product, please wear protective equipment and fully comply with the applicable law and regulations.

Always perform a pre-ride safety check, including brakes, tire pressure, and battery charge. Ensure all components are securely fastened before each ride.

2. Assembly Instructions

The Cybervelo EK7 E-Bike is 90% pre-assembled. Please follow these steps to complete the assembly:

2.1 Unboxing and Part Identification

Carefully remove all components from the packaging. Lay them out to ensure all parts are present.

2.2 Handlebar Installation

1. Use a 5mm hex wrench to loosen the stem top screw.
2. Use a 6mm hex wrench to loosen the stem side screw.
3. Remove the stem and stem screw sets from the fork.
4. Insert the fork into the frame.
5. Place the headset components (silver ring, black cap, spacers) onto the fork tube in the correct order.
6. Ensure the riser screws on the stem face upwards.
7. Place the stem onto the fork tube.
8. Insert the stem top screw (5mm) and tighten it.
9. Tighten the stem side screws (6mm).
10. Attach the handlebar to the stem, ensuring the rubber pad is correctly positioned. Tighten the handlebar screws.

2.3 Kickstand Installation

1. Attach the kickstand to the frame.
2. Align the hole on the kickstand with the hole on the frame and secure it with the provided screw.

2.4 Front Wheel Installation

1. Ensure the brake disc is on the left side of the bike, matching the rear brake disc.
2. Insert the front wheel into the fork dropouts.
3. Take out the front wheel quick release.
4. Insert part 1 of the quick release from the left side of the front wheel.
5. Assemble parts 2 (spring) and 3 (nut) onto the quick release.
6. Tighten the quick release to secure the front wheel firmly, avoiding any looseness.

2.5 Front Fender and Light Installation

1. Attach the front light to the front fork using a 5mm hex wrench.
2. Attach the front fender to the front fork.
3. Tighten the screw, ensuring enough gap between the fender and the tire.
4. The installation sequence is: 1. front light, 2. front fender, 3. front fork.
5. Connect the front light cable. Align the arrows on both sides of the cable and push firmly until connected.
6. Put the brake cable into the hole of the front fork.

2.6 Brake Adjustment

1. Use a 5mm hex wrench to adjust the front brake caliper.
2. Ensure the brake pads are properly aligned with the rotor and provide effective braking.

2.7 Pedal Installation

1. Identify the 'R' (Right) and 'L' (Left) pedals.
2. Attach the 'R' pedal to the right crank arm (clockwise to tighten) using a 15mm wrench.
3. Attach the 'L' pedal to the left crank arm (counter-clockwise to tighten) using a 15mm wrench.

2.8 Rear Rack Installation

1. Put up the rear rack.
2. Align the hole on the frame, the hole on the fender kickstand, and the hole on the rear rack.
3. Secure with screws using a 4mm hex wrench (from multi-tool).

2.9 Rear Light Installation

1. Attach the rear light to the rear rack.
2. Secure with screws using a 10mm wrench.

2.10 Seat Post Installation

1. Attach the seat to the seat post using a 13mm wrench.
2. Open the clip on the frame and insert the seat post.
3. Adjust the seat to a proper height and fasten the clip.

2.11 Battery Insertion/Removal

1. Use the key to unlock the battery.
2. Push the battery safety lock and remove the battery.
3. To insert, align the battery and push it into the frame until it clicks securely. Lock with the key.

3. Operating Your E-Bike

3.1 Riding Modes

Your Cybervelo EK7 E-Bike offers three distinct riding modes:

• Pure Electric Mode: Engage the throttle for motor-only propulsion.
• Pedal Assist Mode (PAS): The motor provides assistance as you pedal. There are 5 Pedal Assist Levels to choose from, allowing you to adjust the motor's power output.
• Classic Bike Mode: Ride the E-Bike like a traditional bicycle, without any motor assistance.

3.2 Intelligent LCD Display

The LCD display serves as your control panel and information hub. It provides real-time data about your ride and allows you to adjust settings:

• 

  Intelligent LCD Display

• 

  LCD Display Functions

• USB Port: Charge your phone or other devices on the go.
• Pedal Assist Level (PAS): Adjust the level of motor assistance while pedaling.
• Real-Time Data: View your current speed, battery level, odometer, and control lights.
• Cruise Control: The cruise control function can be switched on and off easily with the push of a button.

3.3 Gear Shifting

The 7-speed Shimano transmission system allows you to efficiently manage your ride. Shift to easier gears on hills to conserve battery and reduce strain.

7-Speed Gear Shift System

4. Maintenance

4.1 Battery Care

• The 48V 25Ah lithium-ion battery is removable for convenient charging.
• It can also be charged directly on the bike.
• The battery is IP54 waterproof, offering longer service life.
• Always use the original charger provided with your E-Bike.
• Avoid fully discharging the battery regularly. Charge it after each ride or when the charge level is low.
• Store the battery in a cool, dry place, away from direct sunlight and extreme temperatures.

4.2 Brake System

• The E-Bike is equipped with front and rear mechanical disc brakes.
• Regularly check brake pads for wear and replace them when necessary.
• Ensure brake levers are responsive and provide adequate stopping power. Adjust cable tension if needed.

4.3 Tires

• The 26-inch tires are puncture-resistant.
• Maintain proper tire pressure as indicated on the tire sidewall for optimal performance and safety.
• Inspect tires regularly for wear, cuts, or embedded objects.

4.4 General Maintenance

• Keep your E-Bike clean, especially after riding in wet or muddy conditions.
• Lubricate the chain regularly to ensure smooth gear changes and prevent rust.
• Check all bolts and fasteners periodically to ensure they are tight.
• The brushless motor requires low maintenance.

5. Troubleshooting

If you encounter any issues with your Cybervelo EK7 E-Bike, please refer to the following common troubleshooting tips:

• E-Bike not turning on: Check if the battery is properly inserted and locked, and if it has sufficient charge. Ensure all electrical connections are secure.
• Motor not assisting: Verify that the E-Bike is in Pedal Assist Mode (PAS) or Pure Electric Mode. Check the PAS level on the LCD display. Ensure the battery is charged.
• Brakes feel weak: Inspect brake pads for wear. Check brake cable tension and adjust if necessary. Ensure the brake discs are clean and free of oil or grease.
• Unusual noises: Inspect the chain for proper lubrication and tension. Check for any loose components or rubbing parts.
• Display not working: Ensure all display connections are secure. If the issue persists, contact customer service.

For more complex issues, please contact our customer service team for assistance.

6. Specifications

1000W Peak Rear Hub Motor Details

Long-Range 48V 25AH Battery Features

Front & Rear Disc Brakes

Versatile 26" E-Bike for Various Terrains

7. Warranty and Support

Your Cybervelo EK7 E-Bike comes with a one-year warranty. We are committed to providing 100% satisfaction with responsive customer service within 24 hours.

7.1 Warranty Information

Warranty Information Table

7.2 Customer Service

If you have any questions or require assistance with your E-Bike, please contact our customer service team. We aim to respond within 24 hours.

8. User Tips

• Battery Capacity: The Cybervelo EK7 is equipped with a 25Ah battery, providing a long range.
• Regular Checks: Periodically check tire pressure, brake function, and the tightness of all bolts and connections to ensure a safe and smooth ride.
• Terrain Versatility: The E-Bike is designed for various terrains including sand, trails, snow, and city roads. Adjust your riding mode and gear according to the terrain for optimal performance and battery life.