VASTFIRE Hexagonal LED Garage Light Instruction Manual

1. Introduction

Thank you for choosing the VASTFIRE Hexagonal LED Garage Light. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your new lighting system. Please read these instructions carefully before installation and retain them for future reference.

2. Safety Precautions

• Always ensure the power supply is disconnected before installation, maintenance, or cleaning.
• Do not connect too many tubes to a single LED cable to prevent overheating and damage. For 44cm tubes, one LED cable can connect no more than 60 pieces.
• Use the standard municipal electricity AC110V or AC220V voltage supply as appropriate for your model.
• It is forbidden to install lamps and lanterns with live electricity, which may cause damage to the lamps or injure people due to electricity leakage.
• Ensure all connections are secure and properly insulated to prevent electrical hazards.
• The connecting pins are designed to be hidden deep within the light bar to prevent electric shock. Ensure pins are fully inserted and not exposed.

3. Package Contents

Before installation, please check the quantity and completeness of the lamp tubes, fittings, and accessories according to the packing list for your specific kit size.

Typical Components:

• LED Module (440mm Lamp Tube)
• Double V Connector (120°)
• Triple Y Connector (120°)
• Power Cord
• Buckle Screws
• Nylon Cable Ties

Example Kit Quantities:

4. Setup and Installation

The VASTFIRE Hexagonal LED Garage Light system is modular and can be assembled in various configurations. The following steps outline the general assembly and installation process.

4.1 Assembly

1. Connect the LED light tubes using the V-type (2-way) and Y-type (3-way) connectors to form your desired hexagonal pattern. Ensure the pins are fully inserted into the connectors.
2. Apply a small amount of dishwashing liquid or shampoo to the joints to facilitate easier assembly, as the fit can be tight.
3. Once the desired pattern is assembled, connect the power cable to one of the connectors.

4.2 Installation Methods

There are two primary methods for fixing the hexagonal light structure:

Method 1: Fixed to a Mesh Model (Suspended)

This method involves fixing the assembled light structure to a mesh or grid, often used for suspended installations.

• Use cable ties to secure the light structure to an existing mesh or grid system.
• Ensure the mesh model is robust enough to support the weight of the lights.

Method 2: Fixed Directly to the Wall/Ceiling

This method involves directly mounting the light structure to a flat surface like a wall or ceiling.

• Use the provided buckle screws. Put screws through the holes in the corners of the connectors and fix them to the wall or ceiling.
• Ensure appropriate wall plugs are used for your wall/ceiling material to provide a secure fixing.

4.3 Video Guide

For a visual demonstration of the unpacking, assembly, and connection process, please refer to the official product video:

5. Operation

Once installed and securely connected to the power supply, simply plug the power cord into a compatible AC110V or AC220V outlet (depending on your model) to illuminate the lights. The lights are designed for immediate full brightness upon power connection.

This product is not a smart device and does not feature built-in dimming capabilities. If dimming is desired, an external compatible dimmer switch must be installed by a qualified electrician.

6. Maintenance

• Cleaning: Disconnect power before cleaning. Use a soft, dry cloth to wipe the light tubes and connectors. Do not use abrasive cleaners or solvents, as these can damage the finish.
• Inspection: Periodically check all connections to ensure they remain secure. Inspect the power cord for any signs of damage or wear.
• Storage: If disassembling for storage, ensure all components are clean and dry. Store in a cool, dry place away from direct sunlight.

7. Troubleshooting

• Lights not turning on:
  • Check if the power cord is securely plugged into both the light system and the wall outlet.
  • Verify that the wall outlet has power.
  • Ensure all light tubes are correctly connected to the splicers and the pins are fully inserted.
• Flickering lights:
  • Check all connections for looseness.
  • Ensure the power supply is stable and within the specified voltage range.
• Overheating:
  • Ensure you have not connected more than the recommended number of tubes to a single power cable (max 60pcs for 44cm tubes).
  • If you require more tubes, contact support for guidance on connecting additional power cables.

8. Specifications

Kit Specific Power and Luminous Flux:

9. User Tips

• To make assembly easier, apply a small amount of dishwashing liquid or shampoo to the connector joints before pushing the light tubes in.
• The assembled structure is lightweight, making it easy to lift and position for installation.
• While the components are durable, handle them with care during assembly to avoid unnecessary stress on the connections.
• Consider the modularity of the system to create unique lighting designs that best suit your space.
• Be aware that spare LED bars are not typically included in the package.

10. Warranty and Support

If goods are broken or you encounter any issues, please contact VASTFIRE for free replacement. You can reach us via email at 769484812@qq.com.

For further details and comprehensive information, you may refer to the full user manual available in PDF format. A link to the PDF manual is typically provided by the seller or can be found on the product page.