BAOFENG BF-T1

Contents

Baofeng BF-T1 Mini Walkie Talkie User Manual

Model: BF-T1 | Brand: BAOFENG

Introduction

Thank you for purchasing the Baofeng BF-T1 Mini Walkie Talkie. This transceiver is designed for reliable and instant communication, suitable for various uses including car clubs and amateur radio enthusiasts. This manual provides essential information for the safe and efficient operation of your device. Please read it carefully before use.

Important Safety Notice:

  • Only qualified technicians should service this equipment. Do not modify the radio.
  • Use only BAOFENG supplied or approved accessories.
  • Turn off your radio before entering areas with explosive or flammable materials. Do NOT use your transceiver at a gas/fuel station.
  • Avoid prolonged direct sunlight exposure or placing near heating sources.
  • Turn off your radio in areas where notices instruct to do so to avoid electromagnetic interference.
  • Do not transmit for long periods to prevent overheating.
  • Keep the unit away from dusty, damp, and wet environments.

Setup

Unpacking and Inspecting

Carefully open the box and check the packaging for any signs of damage. Confirm that all items listed below are present. If any items are damaged or missing, contact your dealer immediately.

What's in the Box:

Contents of the Baofeng BF-T1 Mini Walkie Talkie package, showing 4 radios, batteries, belt clips, chargers, headsets, and neck straps.
Contents of the Baofeng BF-T1 Mini Walkie Talkie package, showing 4 radios, batteries, belt clips, chargers, headsets, and neck straps.
  • Mini handheld radio
  • Battery
  • Adapter
  • Earpiece
  • Belt clip
  • Hand strap
  • USB charging cable
  • User manual (this document)

Battery Assembly

  1. Open the battery cover using a screwdriver.
  2. Connect the electric lead into the battery socket. You will hear a voice prompt 'welcome' and the channel number.
  3. Align the electric lead into the slot and place the battery smoothly.
  4. Screw the cover back into place.

To remove the battery, reverse these steps.

Charging and Battery Maintenance

The battery should be fully charged before initial use. Optimal battery efficiency is achieved after three full charge and discharge cycles.

When the battery level indicator shows low, the radio will beep periodically, indicating it needs charging.

  1. Connect the charging USB cable to the AC adapter and the radio's socket.
  2. Plug the AC adapter into a main AC wall outlet.
  3. The battery level indicator will show charging status.
  4. When the battery level indicator shows full, the charge is complete. Disconnect the USB charging cable.

Note: The radio should be turned off during the charging cycle.

The battery is not fully charged from the factory. Charge it for at least three to five hours before first use.

Battery Safety:

  • Use only manufacturer-approved batteries.
  • Never attempt to disassemble the battery pack.
  • Do not expose the battery to fire or intense heat.
  • Dispose of batteries according to local recycling regulations.

Belt Clip Attachment

At the back of the radio, there are two parallel screws. Remove these screws, thread them through the holes on the belt clip, and then screw them back into the radio body to secure the belt clip.

Detailed views of the Baofeng BF-T1 radio's features, including the PTT button, antenna, and display.
Detailed views of the Baofeng BF-T1 radio's features, including the PTT button, antenna, and display.

Earpiece Connection

Open the cover of the earpiece jack, align the connector, and push it fully in.

Getting to Know Your Radio

The transceiver features a seven-character segment code alphanumeric LCD with auxiliary icons. The status LED indicates transmission (red), reception (green), and standby (off).

Labeled diagram of the Baofeng BF-T1 radio, highlighting its buttons and interfaces.
Labeled diagram of the Baofeng BF-T1 radio, highlighting its buttons and interfaces.

Keypad Zone:

  • MENU/Lock Key: Used to enter the menu, confirm options, and lock/unlock the keypad (press and hold).
  • FM Radio Key: Momentarily press to start/stop broadcast FM receiver. Press and hold to activate/deactivate alarm function.
  • MONI/Volume Key: Momentarily press to display volume indicator, then use arrow keys to adjust. Press and hold to monitor signal (open squelch).
  • Up/Down Keys: Navigate menus, select channels, adjust volume.
  • Flashlight Key: Momentarily press to turn on/off LED flashlight. Press and hold to enable/disable scanner.
  • SOS Button: Press to initiate an emergency call to all other radios.
  • PTT (Push-to-Talk) Button: Press and hold to transmit.

Operating Instructions

Power and Volume

  • Turning the unit on: Press the On/Off button until you hear a "click". An audible beep will sound, and the display will show a message or flash the LCD, then display a channel. If voice prompt is enabled, it will announce "welcome to use".
  • Turning the unit off: Press and hold the ON/OFF button.
  • Adjusting the volume: Press the MONI/VOL button momentarily. The volume indicator will appear. Use the UP key to increase volume and the DOWN key to decrease volume. Press MONI/VOL again to confirm.

Making a Call

Press and hold the PTT button on the side of the radio body to transmit. Speak approximately 3-5cm from the microphone. Release the PTT button to return to receive mode.

Working the Menu System

  1. Press the MENU key to enter the menu.
  2. Use the arrow keys to navigate between menu items.
  3. Once you find the desired menu item, press MENU again to select it.
  4. Use the arrow keys to select the desired parameter.
  5. To confirm your selection, press MENU. This saves your setting and returns you to the main menu. To cancel changes, press SOS or PTT button; this resets the item and exits the menu.
  6. To exit the menu at any time, press SOS or PTT button.

Scanning

The radio has a built-in scanner. To enable, press and hold the LAMP key for about two seconds. Press LAMP key momentarily to stop scanning.

Scanning Modes:

The scanner can operate in three modes: Time (TO), Carrier (CO), or Search (SE).

  • Time Operation (TO): Scanner stops on a signal, then resumes after a preset time.
  • Carrier Operation (CO): Scanner stops on a signal, then resumes after a preset time with no signal.
  • Search Operation (SE): Scanner stops on a signal. To resume, press and hold the LAMP key.

Setting Scanner Mode:

  1. Press MENU key.
  2. Navigate to the scanner mode menu item using arrow keys.
  3. Press MENU to select.
  4. Use arrow keys to select the desired scanning mode.
  5. Press MENU to save and confirm.
  6. Press SOS or PTT button to exit.

Selective Calling

The BF-T1 supports group calling to filter out unwanted transmissions. This includes CTCSS (Continuous Tone-Coded Squelch System) and DCS (Digital-Coded Squelch).

Note: Using CTCSS/DCS filters unwanted incoming transmissions but does not prevent others from listening to your transmissions. CTCSS/DCS settings can only be changed via programming software.

Diagram illustrating the voice cancellation and VOX (Voice Operated Transmit) features of the Baofeng BF-T1.
Diagram illustrating the voice cancellation and VOX (Voice Operated Transmit) features of the Baofeng BF-T1.

1750Hz Tone-burst

To send a 1750Hz Tone-burst, press the MONI/VOL key while holding down the PTT button. No further configuration is required. This function works even if the keypad lock is enabled.

Repeaters

Repeaters are automated transceivers that relay and amplify signals, extending communication range. To activate the relay function:

  1. Press MENU key.
  2. Navigate to NO.9 RELAYM using arrow keys.
  3. Press MENU to select.
  4. Use arrow keys to select the desired setting.
  5. Press MENU to save and confirm.
  6. Press SOS or PTT button to exit.

Note: RX and TX frequencies can only be programmed by software. For better encoding with CTCSS or DCS, the squelch level should be 5.

Programming

The BF-T1 features 20 memory channels to store frequently used frequencies, transmit power, group signaling information, and bandwidth. These can be easily retrieved later.

Factory Defaults Reset

To reset the radio to factory defaults, press and hold the ON/OFF + MONI/VOL buttons while switching on the radio. Default settings include: 400.025MHz, no CTCSS/DCS, low output power, battery save, volume level 5, width band, SQL 5, key tone ON, and other settings off.

Maintenance

  • Battery Care: Follow charging instructions. Do not expose to extreme temperatures or disassemble.
  • Cleaning: Keep the unit away from dusty, damp, and wet environments. Use a soft, dry cloth for cleaning.
  • Storage: Store the radio in a cool, dry place when not in use for extended periods.

Troubleshooting

Symptom Possible Cause Solution
The radio doesn't start.
  • The battery is too low.
  • The battery isn't correctly installed.
  • Change or recharge the battery.
  • Remove the battery and reinstall it.
The battery dies quickly.
  • The battery is dead.
  • The battery isn't fully charged.
  • Purchase a new battery.
  • Recharge the battery.
The LED indicates reception, but the speaker is silent.
  • Volume is too low.
  • CTCSS or DCS enabled.
  • Turn up the volume.
  • Change the CTCSS or DCS to match those you are trying to communicate.
  • Turn off your CTCSS or DCS.
Others can't hear your transmission.
  • Their CTCSS or DCS settings don't match yours.
  • You are too far apart.
  • Change your CTCSS or DCS settings to match your peers.
  • Move in closer.

Specifications

General Specifications

Frequency Range400.00-470.00 MHz
Storage Channel20
Step Frequency12.5/25KHz
Rated VoltageDC 3.7V
Frequency Stability±2.5ppm
Work Temperature-20°C to +60°C
Battery CapacityH-1500mAh (Li-ion Battery)
Battery LifeAbout 12 Hours
Antenna Impedance50Ω
Dimensions108x55x21 mm (Including Antenna)
Weight120g (Including battery)
MaterialPlastic
Display ScreenYes
Maximum Range3km-5km
Is Batteries IncludedYes
TypePortable, Mini
CertificationCE, Dot, EAC, EPA, FCC, GMP, RoHS, TGA, UL, KC, pse, weee

Transmitter Specifications

Output Power0.5W/1W
Modulation Mode (W/N Band)16KΦF3E/11KΦF3E
Maximum Frequency Deviation (W/N Band)<5KHz/≤2.5KHz
Spurious Power<7.5 μW
Adjacent Channel Power<-65dB/<-60dB
Audio Distortion<5%
SNR≥-45dB/≥-40dB
CTSCC/DCS Frequency Deviation (W/N Band)0.7±0.1KHz (W), 0.4±0.1KHz (N)
Modulation Sensitivity8-12mV
Transmitting Current<1000mA

Receiver Specifications

Sensitivity<0.25 μV (12dB SINAD)
Audio Power1W
Inter modulation Interference Resistance≥65dB (W), ≥60dB (N)
Adjacent Channel Selectivity (W/N Band)≥65dB (W), ≥55dB (N)
Audio Distortion5%
Receiving Current<380mA

CTCSS Table (50)

For a complete list of CTCSS tones, please refer to the full user manual PDF.

DCS Table (210)

For a complete list of DCS codes, please refer to the full user manual PDF.

Warranty and Support

For technical support, programming software, or to obtain a programming cable, please contact your dealer.

Any servicing or repairs should only be performed by qualified technicians. Unauthorized modifications may void your warranty and could lead to unsafe operation.

For detailed information, including full CTCSS and DCS tables, please refer to the official user manual PDF: Baofeng BF-T1 User Manual (PDF).

© 2016 Fujian Nan'an Baofeng Electronic Co., Ltd. All rights reserved.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.