SWEVY SW93S/SW55S

Contents

SWEVY Digital Brix Refractometer User Manual

Models: SW93S, SW55S

Introduction

This manual provides instructions for the operation and maintenance of your SWEVY Digital Brix Refractometer (Models SW93S and SW55S). This high-precision instrument is designed for measuring sugar content (Brix), temperature, and refractive index in various liquids such as juice, milk, and tea. Please read this manual thoroughly before use to ensure proper and safe operation.

SWEVY Digital Brix Refractometer SW-93S showing 10.0% Brix reading

Figure 1: SWEVY Digital Brix Refractometer (SW-93S model)

Parts Overview

Familiarize yourself with the components of your refractometer:

Diagram showing parts of the SWEVY Digital Brix Refractometer including measurement slot, optical prism, LCD screen, power button, reset button, measuring key, and battery compartment.

Figure 2: Key components of the refractometer

  • Measurement Slot / Optical Prism: Where the sample is placed for measurement.
  • LCD Screen: Displays measurement results, temperature, and battery status.
  • Power Button / Reset Button: Press to switch on/off. Hold for 1 second to reset.
  • Measuring Key: Initiates the measurement process.
  • Zero Key: Used for zero-setting the instrument.
  • Battery Compartment (bottom): Houses the AAA batteries.
  • USB Charging Interface: For charging the built-in lithium battery (if applicable to model).

Setup

1. Battery Installation

The device uses AAA batteries for power. To install or replace batteries:

  1. Locate the battery compartment at the bottom of the device.
  2. Open the battery compartment cover.
  3. Insert two AAA batteries, ensuring correct polarity.
  4. Close the battery compartment cover securely.

Video 1: Product demonstration including battery installation and basic operation.

2. Language Switch (Chinese/English)

To switch the display language:

  • When the device is powered on, simultaneously hold down the Power button and the Zero button.
  • The interface will switch between Chinese and English.
Image showing the refractometer display with text 'Chinese-English Language Switch' and instructions to hold Power and Reset buttons simultaneously.

Figure 3: Switching between Chinese and English language interface.

3. Zero-Setting

Before each use, or if accuracy is in doubt, perform a zero-setting with clean water to ensure precise measurements.

  1. Ensure the measurement slot is clean and dry.
  2. Drip approximately 0.3 ml of clean water (or pure water) onto the optical prism, ensuring it covers the entire surface. The water layer should be about 1 mm thick.
  3. Press the "Zero" key (清零). The display will show "Clearing" and then "0.0%".
  4. If the measured value is not 0.0%, press the "Zero" key again to reset.
Diagram illustrating the zero-setting process using clean water on the refractometer's prism.

Figure 4: Zero-setting procedure with clean water.

Operating Instructions

Measurement Steps

  1. Preparation: Ensure the instrument is clean and zero-set. Check precautions before measurement.
  2. Add Sample: Add at least half the volume of the cuvette (approximately 0.3 ml) of the detection sample onto the optical prism. Ensure the sample covers the entire surface.
  3. Measure: Press the "MEAS" key (测量) to aspirate the solution and initiate measurement.
  4. Read Result: The result (Brix, temperature, refractive index) will be displayed on the LCD screen within 3 seconds.
  5. Repeat for Accuracy: For best accuracy, repeat the measurement several times to ensure data consistency.
  6. Clean Up: After measurement, thoroughly clean the sample slot with clean water and wipe with paper towels. Proceed to the next measurement.
Four-step diagram showing the measurement process: checking precautions, adding sample, pressing measure key, and cleaning the slot.

Figure 5: Step-by-step measurement operation.

Image showing quick measurement result display on the refractometer screen.

Figure 6: Fast measurement results in under 3 seconds.

Cautions During Measurement

  • Cold or Hot Measuring Solution: Drop the measuring solution and wait 20 seconds before measuring. The instrument performs temperature compensation, requiring the instrument and solution to maintain the same temperature for accurate results.
  • Measuring Solution Containing Suspended Substances:
    1. Step 1: Remove suspended solids from the measuring solution with a filter spoon or gauze as much as possible.
    2. Step 2: Mix the measuring solution evenly (do not use metal or hard objects, and avoid scratching the optical prism). Uneven solutions or suspended solids can lead to instrumental uncertainty.

Maintenance

Cleaning

Regular cleaning ensures accuracy and extends the life of your refractometer.

  • If there is dirt in the measuring slot or if the instrument has not been used for a long time, it should be cleaned first.
  • If the measuring slot contains oiliness or is difficult to clean, use ethanol or soapy water.
  • Drip clean water onto the prism and wash with paper towels more than three times. Dispose of used towels after wiping.
Diagram illustrating the cleaning process of the refractometer's prism using water and paper towels.

Figure 7: Cleaning the measurement slot.

Storage

  • This instrument is a precise optical device. Prevent it from collision and falling.
  • Do not use hard objects to scratch the optical prism in the measuring slot.
  • When not in use, store the device in a dry place.
  • USB charging voltage should not exceed DC6V limit.

Troubleshooting

Refer to the table below for common issues and their solutions:

Error Message / Status NoticeReasonSolution
Cover with handExternal light is too strong to measure.Perform measurement in a less brightly lit area or shield the prism from direct light.
High temperature / Low temperatureTemperature excess in measuring slot.Allow the instrument and sample to stabilize within the operating temperature range (10-40°C).
Re zeroZero-clearing step needs to be repeated.Follow the zero-setting procedure again with clean water.
Less solution / Less waterToo little solution/clean water in measuring slot.Ensure at least 0.3 ml of sample/water is applied, covering the entire prism surface.
Out of rangeExcessive concentration.The sample's concentration is outside the measurement range. Dilute the sample if necessary.
Low voltageBattery is low.Charge the device using a 5V charger or computer USB.
Call maintenancePossible damage to components.Contact customer support for assistance.

Specifications

FeatureDetail
Measurement Range0-93% Brix (SW93S), 0-55% Brix (SW55S)
Brix Min. Div. / Resolution0.1% Brix
Measurement Accuracy±0.2% Brix / ±1°C
Temperature Compensation10-40°C (Automatic)
Ambient Temperature10-40°C
BatteryBuilt-in lithium battery (600mA) or AAA batteries (depending on model)
Battery Life (Full charge)About 20,000 times measurements
Weight127g
Size114*58*31mm
UseSugar content measurement (Juice, Milk, Tea, etc.)
CertificationCE, RoHS
Image detailing product functions for SWEVY SW55S model, including 0-55% Brix range, 0.1% resolution, +/-0.2% accuracy, Chinese/English interface, HD large screen, temperature/sugar concentration/refractive index display, low battery indication, high/low temperature alert, and 2x AA battery power supply.

Figure 8: Product functions and features for SW55S model.

Image showing the refractometer with automatic temperature compensation feature, indicating operation between 10°C and 40°C for more accurate data.

Figure 9: Automatic temperature compensation for accurate data.

Warranty and Support

Service Voucher

  • The company provides a one-year warranty service for non-man-made damage from the date of purchase.
  • The warranty does not cover:
    • Artificial damage or damage caused by improper use and custody.
    • Failure or damage caused by dismantling and assembling without authorization.
    • Instruments purchased through informal channels.

Additional Resources

A detailed user manual in PDF format is available for download. You can access it here: User Manual (PDF)

User Tips

  • For consistent and accurate results, always perform zero-setting with clean water before each measurement session.
  • Ensure the sample slot is thoroughly cleaned after each use to prevent residue buildup, which can affect future readings.
  • When measuring, ensure the sample completely covers the optical prism for reliable results.
  • If measuring very hot or cold liquids, allow the sample to reach room temperature or within the device's operating range (10-40°C) for optimal temperature compensation.

Frequently Asked Questions (FAQ)

Q: Is this refractometer suitable for measuring water content in honey?
A: The SWEVY Digital Brix Refractometer measures Brix (sugar content). While honey's sugar content is related to its water content, this specific model is primarily designed for Brix measurement. For precise water content in honey, a specialized honey refractometer might be more appropriate.

Safety Warnings

  • This instrument is a precise optical device. Handle with care to prevent collision and falls.
  • Do not use hard objects to scratch the optical prism in the measuring slot.
  • Ensure the USB charging voltage does not exceed DC6V.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.