SWEVY SW6016

Contents

SWEVY SW6016 Handheld Digital Anemometer User Manual

High Precision Wind Speed and Temperature Measurement

1. Introduction

Thank you for choosing the SWEVY SW6016 Handheld Digital Anemometer. This device is designed for precise measurement of wind speed and environmental temperature. Its high-precision probe and multiple measurement modes make it suitable for various applications, including outdoor activities, HVAC system checks, and environmental monitoring. Please read this manual thoroughly before using the device to ensure safe and optimal performance.

2. Package Contents

  • SWEVY SW6016 Handheld Digital Anemometer
  • User Manual (this document)

Note: Batteries are not included and must be purchased separately.

3. Product Overview

The SWEVY SW6016 features a compact design with an easy-to-read LCD and intuitive controls.

SWEVY SW6016 Anemometer with labeled components and dimensions

Figure 1: SW6016 Anemometer Components and Dimensions

3.1. Device Components

  1. Wind Speed Sensor: Six-blade impeller for accurate wind speed detection. Rotates 180 degrees.
  2. LCD Display: Digital screen showing wind speed, temperature, battery status, and mode indicators.
  3. Power Button (⏻): Turns the device ON or OFF.
  4. Mode Button (MODE): Cycles through different measurement modes (Lock, MAX, MIN, Average).
  5. Backlight Lamp Button (💡): Toggles the display backlight ON or OFF.
  6. Unit Switch Key (UNIT): Changes the wind speed measurement units.

4. Setup

4.1. Battery Installation

The SWEVY SW6016 requires user-supplied batteries. Locate the battery compartment (typically on the rear or bottom of the device). Open the cover, insert the required batteries (e.g., AAA, specific type not provided in product details, please check device markings if present) according to the polarity indicators (+/-), and then securely close the battery compartment cover.

5. Operating Instructions

SWEVY SW6016 Anemometer displaying wind speed and temperature, highlighting range and resolution

Figure 2: High Precision Measurement Capabilities

5.1. Powering On/Off

  • To Power On: Press the Power Button (⏻). The LCD will illuminate and display current readings.
  • To Power Off: Press and hold the Power Button (⏻) for a few seconds until the display turns off.

5.2. Taking Measurements

Once powered on, hold the anemometer so that the wind speed sensor (impeller) is facing the airflow you wish to measure. The device will instantly display the current wind speed and environmental temperature on the LCD.

5.3. Switching Measurement Modes

The SW6016 offers various measurement modes for different needs. Press the MODE button to cycle through them:

SWEVY SW6016 Anemometer showing AVG, HOLD, MIN, MAX modes

Figure 3: One-Click Switch Function for Measurement Modes

  • Real-time (Default): Displays the current wind speed.
  • HOLD: Freezes the current reading on the display. Press MODE again to release.
  • MAX: Displays the maximum wind speed recorded since the device was powered on or reset.
  • MIN: Displays the minimum wind speed recorded since the device was powered on or reset.
  • AVG (Average): Displays the average wind speed over a period.

5.4. Changing Wind Speed Units

The device supports four common wind speed units. Press the UNIT button to switch between them:

SWEVY SW6016 Anemometer showing m/s, Knots, Km/h, MPh units

Figure 4: Freely Switchable Wind Speed Units

  • Meters per second (m/s)
  • Knots
  • Kilometers per hour (Km/h)
  • Miles per hour (MPh)

5.5. Using the Backlight

In low-light conditions, press the Backlight Lamp Button (💡) to turn the LCD backlight ON. Press it again to turn the backlight OFF.

6. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the device. Do not use abrasive cleaners or solvents. Ensure the wind speed sensor is free from dust and debris for accurate readings.
  • Storage: When not in use for extended periods, remove the batteries to prevent leakage. Store the device in a cool, dry place away from direct sunlight and extreme temperatures.

7. Troubleshooting

  • Device does not turn on: Check if batteries are installed correctly and have sufficient charge. Replace batteries if necessary.
  • Inaccurate readings: Ensure the wind speed sensor is clean and unobstructed. Make sure the device is held correctly in the airflow.
  • Display issues: If the display is dim or flickering, replace the batteries.

If you encounter persistent issues, please contact customer support.

8. Specifications

SWEVY SW6016 Anemometer high-precision six-blade probe

Figure 5: High-Precision Six-Blade Probe Design

FeatureSpecification
ModelSW6016
TypeHandheld Digital Anemometer
Wind Speed Range0.3 ~ 30 m/s
Wind Speed Resolution0.1 m/s
Wind Speed Unitsm/s, Knots, Km/h, MPh
Temperature MeasurementYes (Environmental Temperature)
DisplayDigital LCD with Backlight
Probe TypeIntegrated Six-blade, 180° Rotatable
Dimensions (H x W x D)163mm x 50mm x 26mm (6.42in x 1.97in x 1.02in)
BatteryUser-supplied (Not Included)
CertificationsCE, RoHS
OriginMainland China

9. User Tips

  • For the most accurate wind speed readings, ensure the anemometer's impeller is directly facing the wind source.
  • Avoid blocking the temperature sensor (if visible) to ensure accurate ambient temperature readings.
  • Regularly check battery levels, especially before critical measurements, to prevent unexpected power loss.

10. Safety Information

  • Do not attempt to disassemble or modify the device. This may cause damage and void any warranty.
  • Keep the device away from water and high humidity to prevent electrical damage.
  • Do not expose the device to extreme temperatures or direct sunlight for prolonged periods.
  • Keep out of reach of children.

11. Warranty and Support

SWEVY products are manufactured to high-quality standards. For warranty information, technical support, or service inquiries, please refer to the documentation provided at the time of purchase or contact your retailer. Please retain your proof of purchase for warranty claims.

© 2023 SWEVY. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.