Yinuogo YNG128

Contents

Yinuogo AVIDSEN Garage Door Remote Control User Manual

Model: YNG128

1. Product Overview

The Yinuogo YNG128 is a 4-button rolling code remote control designed for garage doors and gates, operating at a frequency of 433.92MHz. It is compatible with various AVIDSEN systems, offering a reliable solution for remote access.

Two Yinuogo remote controls, one showing the back label with model and frequency, the other showing the four control buttons.
Figure 1: Yinuogo YNG128 Remote Control. The back label indicates model Ref: 114253, frequency 433.92MHz, and CE certification.
Image showing the Yinuogo remote control alongside various Avidsen remote models it is compatible with, including 104250, 114253, 104251, 614701, 104257, 654100, 104350, 654250, 104700, 654300.
Figure 2: Compatibility with AVIDSEN models.

2. Setup and Programming

Programming this remote control requires access to your existing garage door or gate receiver unit. Ensure you can physically access the receiver before starting the programming process.

2.1 General Programming Steps (Refer to your receiver's manual for specific button names)

  1. Access the Receiver: Open the casing of your garage door/gate receiver unit. This unit is typically located near the motor.
  2. Activate Programming Mode: On the receiver's circuit board, locate and press the programming button (it might be labeled ENR, MEMO, PROG, REC, or similar). Release the button. The LED light on the receiver should illuminate or blink, indicating it's in programming mode.
  3. Program the Remote: While the receiver's LED is active, press one of the buttons on your new Yinuogo remote control for approximately 1 second. Then release the button.
  4. Confirmation: The LED light on the receiver will typically turn off immediately or within 10 seconds, confirming that your new remote control button has been successfully programmed.

2.2 Visual Programming Guide

Four-panel diagram illustrating different programming methods for garage door remotes. Each panel shows a different receiver board layout and the sequence of pressing buttons on the receiver and then the remote.
Figure 3: Various receiver programming interfaces. Follow the sequence: press receiver button, then press remote button.

2.3 Video Programming Demonstration (Avidsen Receiver Example)

Video 1: Programming an Avidsen receiver for Channel 1 and Channel 2.

  1. Programming Channel 1:
    • Open the Avidsen receiver box.
    • Press the programming button on the receiver. The Channel 1 light will illuminate.
    • Press the desired button on your new remote control.
    • The receiver's light will blink, indicating successful programming.
  2. Programming Channel 2:
    • To program Channel 2, press the receiver's programming button twice. The Channel 2 light will illuminate.
    • Press and hold the desired button on your new remote control.
    • The receiver's light will blink, indicating successful programming.

3. Operating Instructions

Once programmed, operating your garage door or gate is straightforward:

  1. Point the remote control towards your garage door or gate.
  2. Press the programmed button on the remote control.
  3. The garage door or gate will activate (open or close). Pressing the button again will typically stop or reverse the action.

4. Maintenance

4.1 Battery Replacement

The remote control comes with a battery included. When the remote's range decreases significantly or it stops responding, the battery may need replacement.

  • Battery Type: This remote typically uses a CR2032 3V coin cell battery or an A27 12V battery, depending on the specific batch. Please open the remote carefully to verify the battery type before purchasing a replacement.
  • Procedure: Carefully open the remote control casing (usually by prying it open with a small flat-head screwdriver). Remove the old battery and insert the new one, ensuring correct polarity (+/-). Close the casing securely.

4.2 Cleaning

Wipe the remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these can damage the casing or internal components.

5. Troubleshooting

  • Remote Not Responding:
    • Check if the battery is dead. Replace it if necessary.
    • Ensure the remote is within range of the receiver.
    • Verify that the remote is correctly programmed to your receiver. If unsure, repeat the programming steps.
    • Check for any obstructions between the remote and the receiver.
  • Reduced Range:
    • The battery might be low. Replace it.
    • Ensure there are no new sources of radio interference near your receiver or remote.
  • Door/Gate Opens/Closes Randomly:
    • This is rare with rolling code remotes but can indicate interference or a faulty receiver. Consult your garage door opener's manual or a professional.

6. Specifications

Brand NameYinuogo
Model NumberYNG128
Frequency433.92MHz
Encoding MethodRolling Code
Number of Buttons4
BatteryIncluded (Type: CR2032 3V or A27 12V - verify inside unit)
CertificationCE, FCC, RoHS, WEEE
OriginMainland China
Package Dimensions8cm x 8cm x 8cm (approx.)
Package Weight0.06 kg (approx.)

7. User Tips

  • Easy Programming: Many users find the programming process straightforward. Follow the steps carefully, and refer to the video demonstration if needed.
  • Verify Battery Type: Before purchasing a replacement battery, always open your remote to confirm whether it uses a CR2032 3V or an A27 12V battery.
  • Keep Receiver Accessible: For future programming or troubleshooting, ensure your garage door/gate receiver unit remains accessible.

8. Warranty and Support

For warranty information or technical support, please refer to the seller's policies or contact the point of purchase. Keep your purchase records for any warranty claims.

© 2024 Yinuogo. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.