1. Introduction
The YSRSAI V5-SP is a versatile 5-in-1 LED strip controller designed for single color, color temperature (CCT), RGB, RGBW, and RGB+CCT LED strips. It offers smart control via Tuya APP, RF 2.4GHz remote, voice commands through Alexa and Google Home, and external push switches. This manual provides detailed instructions for installation, operation, and troubleshooting to ensure optimal performance of your LED lighting system.
2. Product Overview & Features
The V5-SP controller supports a wide range of LED strip types and offers multiple control methods for a flexible lighting experience.
Key Features:
- 5-in-1 Functionality: Compatible with DIM (single color), CCT (dual color), RGB, RGBW, and RGB+CCT LED strips.
- Smart Control: Tuya APP (Smart Life APP) for remote control, scheduling, and scene management.
- Voice Control: Works with Amazon Alexa and Google Home for hands-free operation.
- RF 2.4GHz Control: Supports RF 2.4GHz remotes for local control (up to 10 remotes per controller).
- Push Switch Input: Connect an external push switch for on/off, brightness, and color adjustments.
- Dynamic Modes: Built-in 10 dynamic modes for RGB/RGBW/RGB+CCT lights (jump or gradual change).
- Auto-Transmitting Function: Extends remote control distance by transmitting signals between controllers.
- Smooth Dimming: 4096 levels of 0-100% dimming without flicker.
- Safety Features: Reverse polarity and over-heat protection.

Figure 1: Overview of V5-SP (RF) and V5-SP(WT) (WiFi & RF) LED Controllers with smart home compatibility.
3. Setup
3.1 Wiring Diagram
Ensure all power is disconnected before performing any wiring. Connect the LED controller to your LED strips and power supply as shown in the diagrams below. The V5-SP(WT) model includes WiFi functionality in addition to RF.

Figure 2: V5-SP(WT) Controller with labeled components and dimensions. Note: Mounting ears can be broken along the indentation to suit mounting needs.
Component Labels:
- LED indicator: Shows status and light type setting.
- RF antenna: For 2.4GHz remote communication.
- Installation rack: For mounting.
- Push switch input (P, GND): For external push button control.
- Power input (V-, V+): Connect to 12-24VDC power supply.
- LED output (V+, R, G, B, W, C): Connect to LED strip.
- Match/Set key: For pairing remotes and setting light type.
Wiring Examples:
Below are common wiring configurations for different LED strip types. Always ensure correct polarity (V+ to V+, V- to corresponding color channel).
For RGB+CCT Light (LED indicator: Blue)
Connect the RGB+CCT LED strip to the controller's V+, R, G, B, W, and C terminals. Power the controller with a 12-24VDC constant voltage power supply. An optional push switch can be connected to the P and GND terminals.

Figure 3: Wiring for RGB+CCT LED strip with push switch and power supply.
For RGBW Light (LED indicator: Green)
Connect the RGBW LED strip to the controller's V+, R, G, B, and W terminals. Power the controller with a 12-24VDC constant voltage power supply. An optional push switch can be connected.

Figure 4: Wiring for RGBW LED strip with push switch and power supply.
For RGB Light (LED indicator: Red)
Connect the RGB LED strip to the controller's V+, R, G, and B terminals.

Figure 5: Wiring for RGB LED strip.
For CCT Light (LED indicator: Yellow)
Connect the CCT LED strip to the controller's V+, W (Warm White), and C (Cool White) terminals.

Figure 6: Wiring for CCT LED strip.
For DIM Light (LED indicator: White)
Connect the single color LED strip to the controller's V+ and V- terminals (or the designated single color output).

Figure 7: Wiring for single color (DIM) LED strip.
3.2 Wire Preparation
- Wire Type: Use solid or stranded wires with a cross-sectional area of 0.5 to 2.0 mm². Conventional 1mm² can withstand 10A output current.
- Terminal Tightening: Ensure all terminals are tightened securely. Loose connections can cause high contact resistance, leading to overheating and potential damage, especially under full load.
- Power Supply Sizing: The output power of your constant voltage power supply should be at least 1.2 times the total output load (LED strip power). Insufficient power can cause flickering or unstable light operation.
3.3 Light Type Setting
Before matching with an RF remote control, you need to set the correct light type on the controller using the SET key.
- Press and Hold: Long press the SET key for 2 seconds to switch to the next light type.
- Sequential Switching: The controller cycles through 5 light types sequentially with each 2-second press.
- LED Indicator: The LED indicator on the controller will change color to correspond to the selected light type:
| Light Type | LED Indicator Color |
|---|---|
| DIM | White |
| CCT | Yellow |
| RGB | Red |
| RGBW | Green |
| RGB+CCT | Blue |
Note: For RGBW light type, RGB channels and W channel cannot be turned on simultaneously. For RGB+CCT light type, RGB channels and CCT channels cannot be turned on simultaneously.
3.4 Installation Precautions
- Heat Dissipation: Do not stack products. Maintain a distance of at least 20cm between units to ensure proper heat dissipation and extend product lifespan.
- Electromagnetic Interference: Do not install the product closer than 20cm to switching power supplies to avoid radiation interference.
- Remote Control Range: Install the controller at least 1 meter from the floor to avoid shortening the remote control distance due to weak reception signals.
- Obstructions: Keep the product at least 20cm away from or uncovered by metal objects to prevent signal attenuation and reduced remote distance.
- Location: Avoid installation in wall corners or beam corners, maintaining a distance of at least 20cm to prevent signal interference.
4. Operating Instructions
4.1 Matching with RF Remote Control
You can match or delete RF remote controls using two methods:
Method 1: Use Match Key
- To Match: Short press the Match key on the controller. Immediately press the on/off key (for single zone remotes) or a zone key (for multiple zone remotes) on your RF remote. The LED indicator will blink to confirm successful matching.
- To Delete: Press and hold the Match/Set key for 5 seconds on the controller. The LED indicator will blink to confirm all matched remotes have been deleted.
Method 2: Use Power Restart
- To Match: Switch off the power to the controller, then switch it back on. Repeat this power cycle. Immediately short press the on/off key (or zone key) on your RF remote 3 times. The LED indicator will blink 3 times to confirm successful matching.
- To Delete: Switch off the power to the controller, then switch it back on. Repeat this power cycle. Immediately short press the on/off key (or zone key) on your RF remote 5 times. The LED indicator will blink 5 times to confirm all matched remotes have been deleted.
4.2 Push Switch Dimming
The push switch interface (P, GND) can be connected to a standard push panel switch or push button for dimming control. It is recommended that no more than 25 controllers are connected to the same push switch, and the connecting wire length should not exceed 20m.
- DIM Light (Single Color):
- Short press: Turn the light on or off.
- Long press (1-6s): Continuously increase or decrease brightness (1%-100%). Release and long press again to change direction.
- Double-click: Switch between 10% and 100% brightness.
- CCT Light (Color Temperature):
- Short press: Turn the light on or off.
- Long press (1-6s): Adjust brightness (1%-100%). Release and long press again to change direction.
- Double-click: Cycle through three color temperatures (warm white, neutral white, cool white). Long press after double-click to fine-tune color temperature. Exits adjustment after 5s of inactivity.
- RGB Light:
- Short press: Turn the light on or off.
- Long press (1-6s): Adjust brightness (1%-100%). Release and long press again to change direction.
- Double-click: Switch between color light (RGB) and mixed white light (50% saturation). Long press after double-click to fine-tune color or saturation. Exits adjustment after 5s of inactivity.
- RGBW Light:
- Short press: Turn the light on or off.
- Long press (1-6s): Adjust brightness (1%-100%). Release and long press again to change direction.
- Double-click: Switch between color light (RGB) and white light. Long press after double-click to fine-tune color or white light brightness. Exits adjustment after 5s of inactivity.
- RGB+CCT Light:
- Short press: Turn the light on or off.
- Long press (1-6s): Adjust brightness (1%-100%). Release and long press again to change direction.
- Double-click: Switch between color light (RGB) and color temperature. Long press after double-click to fine-tune color or color temperature. Exits adjustment after 5s of inactivity.
4.3 On/Off Fade Time Setting
- Restore Default Parameters: Press and hold the SET key for 10 seconds. Factory defaults are: RGB+CCT light type, 100% brightness, and 0.5s light on/off fade time.
- Set Fade Time to 3s: Press and hold the SET key for 15 seconds to set the light on/off fade time to 3 seconds.
4.4 Dynamic Change Mode (Recalled by RF Remote Control)
The controller supports various dynamic modes that can be recalled via the RF remote control.
For RGB/RGB+W:
| No. | Name | No. | Name |
|---|---|---|---|
| 1 | RGB jump | 6 | RGB fade in and out |
| 2 | RGB smooth | 7 | Red fade in and out |
| 3 | 6 color jump | 8 | Green fade in and out |
| 4 | 6 color smooth | 9 | Blue fade in and out |
| 5 | Yellow cyan purple smooth | 10 | White fade in and out |
For RGB+CCT:
| No. | Name | No. | Name |
|---|---|---|---|
| 1 | RGB jump | 6 | RGB fade in and out |
| 2 | RGB smooth | 7 | Red fade in and out |
| 3 | 6 color jump | 8 | Green fade in and out |
| 4 | 6 color smooth | 9 | Blue fade in and out |
| 5 | Color temperature smooth | 10 | White fade in and out |
4.5 App Control (Tuya Smart APP)
The V5-SP(WT) controller integrates with the Tuya Smart APP (also known as Smart Life APP) for advanced control features.
- Remote Control: Control your lights from anywhere using cloud data support.
- Color & Scene Selection: Access a full-color spectrum, pre-set scenes, and music sync modes.
- Timer & Schedule: Set schedules to automatically turn your lights on/off at specific times.

Figure 8: Examples of the Tuya Smart APP interface for LED control.

Figure 9: Cloud data enables long-distance control, and the app features timer and schedule functions.
4.6 Voice Control (Alexa, Google Home)
Integrate your V5-SP(WT) controller with Amazon Alexa or Google Home for convenient voice control.
- Basic Commands: Use commands like