1. Introduction
The HIROYASU IC-980Pro is a compact and powerful 144/430 VHF/UHF Dual Band FM Mobile Transceiver designed for reliable communication. This manual provides detailed instructions for setting up, operating, and maintaining your device to ensure optimal performance.
Key Features:
- VHF: 136-174MHz (Tx&Rx)
- UHF: 400-470MHz (Tx&Rx)
- FM Radio: 76-108MHz (Rx)
- Output Power: 10W-25W
- Storage Channels: 200
- Dual Watch Functionality
- Denoise Feature
- Name Display
- Compact Design
2. Safety Information
- Do not attempt to configure your transceiver while driving.
- This transceiver is designed for use with a 13.8V DC power supply or a standard vehicle battery. Do not use with a 24V battery.
- Keep away from interferential devices, such as TVs, generators, etc.
- Do not expose the transceiver to long periods of direct sunlight or place it close to heating appliances.
- If an abnormal odor or smoke is detected coming from the transceiver, turn the power off immediately and contact your dealer.
- Do not transmit on high power for extended periods, or the transceiver may overheat.
3. Setup
3.1. Unpack and Inspect Contents
Carefully unpack the box and verify that all items are present and undamaged:
- HIROYASU IC-980Pro Mobile Transceiver
- MH-18 Microphone, clip, and screws
- Mounting bracket, washers, and screws
- Power cable with cigarette lighter plug and spare fuse
- User Manual (PDF available for download)
If any items are missing or damaged, please contact your dealer immediately.
Video: Unboxing and basic setup demonstration of the HIROYASU IC-980Pro Mobile Transceiver.
3.2. Physical Installation
Mount the unit in a vehicle or other suitable enclosure. Ensure proper ventilation around the unit.
Rear Panel Connections:
- Antenna Connector (UHF SO-239): Connect a suitable dual-band antenna. Attempting to transmit without an antenna may cause damage to the internal circuitry.
- Fan: The integrated fan will turn on when the internal circuitry becomes hot during extended transmission (e.g., over 5 minutes at high power output). It will turn off when cooled.
- Data Connector (Type C USB): Used to program radio memory channels via software.
- Power Cable: Connect the supplied power cable (red wire to positive, black wire to negative) to a 13.8V DC power supply or vehicle battery. The supplied cable includes a cigarette lighter plug for convenience. Warning: Never remove the fuse holders from the DC cable.
- Speaker Connector (SP): This 1/8" (3.5mm) monoaural connector accepts a cable to an external speaker. The internal speaker is disabled when an external speaker is plugged in.

Image: HIROYASU IC-980Pro Mobile Transceiver mounted in a vehicle, showing the microphone.
4. Operating Instructions
4.1. Front Panel Controls
The front panel features two knobs, five buttons, a microphone connector, and a colored display screen.
- Volume Knob and Power On/Off Button: Push and hold for 2 seconds to turn the radio On or Off. Turn clockwise to increase volume, counterclockwise to decrease.
- V/M Button: Switches the currently selected VFO (A or B) between VFO mode and Memory mode.
- Channel/Menu Selection Knob and Enter Button: Pushing this button initiates Settings editing or confirms changes. Turning the knob changes the selected Channel, Frequency, or choice during editing.
- Monitor Button (MONI): Opens the receiver squelch to hear weak transmissions.
- Colored Display Screen: Shows Channel Name, Channel Number, Channel Frequency, CTCSS/DCS status, Input Voltage, Signal Strength, VOX status, and Keypad Lock status.
- MENU Button: Enters Settings editing mode. Confirms new values during setting selection.
- EXIT Button: Closes the current Settings editing screen and moves to the previous screen. Cancels changes if a setting is being changed.
- PTT Button: Push-To-Talk button for transmission.
- Microphone Connector: Connects the supplied MH-18 microphone.
- Mic in the Front Panel: Built-in microphone for talking if selected as the active microphone.

Image: HIROYASU IC-980Pro Mobile Transceiver displaying VHF and UHF frequencies, with the microphone.
4.2. Microphone Controls (MH-18)
The MH-18 microphone has buttons on the top, a PTT button on the side, and a keypad on the front, along with two status lights.
- A/B Buttons: Used to switch which VFO (A or B) is the MAIN. Only the MAIN VFO can be changed.
- RX/TX Lights: Green light indicates signal reception, Red light indicates transmission.
- PTT Button: Push to transmit, release to stop. Wait 1-2 seconds after pushing before speaking for repeater networks.
- Keypad: Used to enter frequency values and activate functions.
4.3. Basic Operation
The transceiver operates in two RF modes: VFO mode and Memory mode. The front panel display shows two frequencies or channels (Main and Sub).
- Receiving: When a signal is received, the Green RX light on the Microphone will turn on. Audio will be heard from the speaker. Signal strength is shown at the bottom of the display.
- Transmitting: Push the PTT button. Ensure Power, CTCSS, SFT-D, and SFT Frequency settings are correct. Hold the microphone 1-2 inches from your lips and speak normally. The Red TX light will turn on.
4.4. Scanning
To activate scanning, press FUN + 9 on the microphone.
- VFO Mode: Scans frequencies starting from your input frequency.
- Memory Channel Mode: Scans channels starting from your selected channels.
- Use the microphone's
Akey for upward scanning andBkey for downward scanning. - The scanner will stop on a frequency or channel when a signal is detected and is strong enough to activate the squelch.
4.5. VFO Mode
In VFO mode, you can change the frequency by entering a 6-digit frequency using the microphone keypad. Alternatively, use the Channel knob on the front panel or the Up and Down arrows on the microphone keypad. If the displayed frequency is not as expected, check the 'Step' setting.
4.6. Memory Mode
In Memory mode, the radio uses stored channel settings. Select the desired channel by turning the channel knob or entering the channel number (001 to 200) using the microphone keypad. The display can show either the channel number (e.g., CH-001) or a custom channel name.
4.7. Settings Menu
Access the Settings menu by pushing the Front Panel MENU button, pushing the button on the Front Panel Channel/Menu selection knob, or pushing the FUN button on the microphone. Exit the menu using the Front Panel EXIT button or the microphone EXIT button.
4.7.1. RF Function (Menu Option 1)
- 1.1 SQL (Squelch): Silences receiver audio when no signal is received. Range: 0-9.
- 1.2 Power: Transmitter power output. Choices: High (25W), Low (10W).
- 1.3 Compandor: Enhances voice quality by suppressing noise. Choices: On, Off.
- 1.4 Scramble: Encrypts speech signals. Choices: Off, Scramble 1-8.
- 1.5 Bandwidth: Transmitted signal bandwidth. Choices: Wide, Narrow.
- 1.6 BCLO (Busy Channel Lock): Prevents transmission if a signal is being received. Choices: Off, QDT, CAT.
- 1.7 TOT (Time Out Timer): Limits transmission time. Range: 30s-270s.
- 1.8 TOA (Time Of Arrival): Prompt tone before PTT transmission ends. Choices: Off, 1s-10s.
- 1.9 SFT-D (Shift Direction): Sets whether transmit frequency is higher (+) or lower (-) than receive frequency for repeaters. Choices: Off, +, -.
- 1.10 SFT Frequency: Difference between TX and RX frequencies. Default: 0.00000 MHz.
- 1.11 Tx Frequency: Shows resultant TX frequency (not user-changeable).
- 1.12 Step: Sets the value of the last digit in the frequency. Choices: 2.5K, 5K, 6.25K, 10K, 12.5K, 20K, 25K, 30K, 50K.
4.7.2. CTCSS/DCS (Menu Option 2)
- 2.2 R-CTC/DCS: Selects CTCSS or DCS for the receiver. Choices: OFF, CTCSS, DCS, IDCS.
- 2.3 T-CTC/DCS: Selects CTCSS or DCS for the transmitter.
- 2.4 Special DCS: Special encryption codes. Choices: Off, Special DCS 1-3.
4.7.3. SET (Menu Option 3)
- 3.1 Work Mode: Current mode of the selected VFO. Choices: Frequency, Channel, Memory.
- 3.2 ROG Beep: Transmits a sequence of tones at the end of transmission. Choices: Off, 1, 2, 3.
- 3.3 Home Channel: Selects which saved channel is the Home Channel.
- 3.4 A/B Switch: Enables automatic switching to the VFO with a received signal. Choices: Off, Auto, On.
- 3.5 Double Watch: Allows receiving signals from both Band A and Band B simultaneously. Choices: Off, On.
- 3.6 VOX Gain: Initiates transmission when microphone senses audio input. Choices: Off, 1-9.
- 3.7 VOX Delay: Delay at the end of VOX transmission. Choices: 0.3s-3.0s.
- 3.8 Key Tone: Enables a tone for each button press. Choices: On, Off.
- 3.9 1750Hz tone: Access tone for repeaters. Choices: Off, 1/2/3/4/5s.
- 3.10 Mic: Selects active microphone (hand microphone or front panel). Choices: in hand, device host.
- 3.11 Denoise: Background noise canceling. Choices: On, Off.
- 3.12 Key Lock: Manual or automatic keypad lock. Choices: Manu, Auto.
- 3.13 Lamp Control: Controls how long the display and microphone lights stay lit. Choices: 5s, 10s, 15s, 20s, On.
- 3.14 Language: Sets the language for settings screens. Choices: English, Chinese.
- 3.15 APO (Automatic Power Off): Turns radio off after a set period of inactivity. Choices: Off, 10m, 30m, 1h-12h.
- 3.16 Power on mode: Determines radio behavior when power is applied. Choices: OFF, ON, AUTO.
- 3.17 Reset: Performs a reset to factory defaults. Choices: VFO (clears VFO frequencies), ALL (clears all memories and settings).
- 3.18 Scan Resume: How the scanner resumes after halting on a signal. Choices: Carrier, Time, Seek.
- 3.19 PriScan (Memory Channel Priority Scan): Choices: OFF, memory channels.
- 3.20 Scan Add: Adds or deletes a channel for scan. Choices: Add, Del.
- 3.21 Delete Ch: Deletes an existing channel from Memory.
- 3.22 Name Edit: Adds or changes an alphanumeric name for each channel.
- 3.23 Name Display: Determines if the channel name should be displayed. Choices: Off, On.
4.8. Saving a Memory Channel
The radio has memory for 200 channels. To save a new Memory Channel:
- Put the desired VFO (A or B) into VFO mode.
- Enter the receive frequency using the microphone keypad or Channel Select knob.
- Set other necessary parameters: Power, SFT-D, SFT Frequency, and DCS/CTCSS tone.
- Enter the Edit Menu by pushing the button on the Channel Select knob or the microphone
FUNbutton, then press the0key on the microphone. - The display will show 'SAVE->' or 'Cover->' followed by a three-digit channel number.
- Use Up/Down arrows or the Channel Select knob to choose the desired channel number.
- Push
FUNorMENUto confirm. The word 'OK' will be displayed upon successful saving. - To cancel storing, push the PTT button.
4.9. Programming Channel Data
You can program the transceiver using a certified Android USB-C cable and dedicated software. Please consult your dealer for programming software sharing.
Quick-Access Menu Settings (Microphone Keypad):
| Key Combination | Function |
|---|---|
FUN + 0 | Save a memory channel (in VFO Mode) |
FUN + 1 | For SQL setting |
FUN + 2 | For Power output selection |
FUN + 3 | For Dual Watch setting |
FUN + 4 | For C-CTC/DCS settings |
FUN + 5 | For R-CTC/DCS settings |
FUN + 6 | For T-CTC/DCS settings |
FUN + 7 | Enable/disable FM radio |
FUN + 8 | Offset frequency |
FUN + 9 | Scan |

Image: HIROYASU IC-980Pro Mobile Transceiver displaying FM radio frequency in a car dashboard.

Image: HIROYASU IC-980Pro Mobile Transceiver displaying 'Denoise On' feature, with a person driving.

Image: HIROYASU IC-980Pro Mobile Transceiver displaying 'Name Display On' feature in a car dashboard.
5. Maintenance
- Cleaning: Use a soft, dry cloth to clean the exterior of the transceiver. Avoid using harsh chemicals or abrasive cleaners.
- Fuse Replacement: The power cable includes fuse holders. If a fuse blows, replace it with a fuse of the same rating. Never remove the fuse holders.
- Antenna Care: Ensure your antenna is properly connected and maintained. A damaged or improperly connected antenna can affect performance and potentially damage the transceiver.
- Environmental Conditions: Avoid exposing the transceiver to extreme temperatures, direct sunlight, or high humidity.
6. Troubleshooting
- No Power: Ensure the power cable is securely connected to a 13.8V DC source. Check the fuse in the power cable.
- No Transmission/Reception: Verify antenna connection. Check Power, CTCSS, SFT-D, and SFT Frequency settings. Ensure you are in the correct VFO or Memory mode.
- Overheating: If the transceiver overheats, reduce transmission time or output power. Ensure adequate ventilation.
- Abnormal Noise/Smoke: Immediately turn off the power and disconnect the device. Contact your dealer for assistance.
- Unexpected Frequency Display: Check the 'Step' setting in the RF Function menu (1.12). Adjust if necessary.
- Weak Signals/Noise: Adjust the SQL (Squelch) setting (1.1). A value too low results in noise, too high may miss weak signals.
- Communication Issues with Other Radios: If using scrambling, ensure all radios have the same scrambling settings.
- Constant Clicking Sound: If experiencing constant clicking, especially with Dual Watch enabled, try disabling the Double Watch feature (3.5).
- Scanner Resumes Unexpectedly: Check the Scan Resume setting (3.18). If set to 'Time', it will resume after 5 seconds if no action is taken.
7. Specifications
| Feature | Specification |
|---|---|
| Tuner Technology | VHF, UHF |
| Dimensions | 108mm x 40mm x 102mm |
| Storage Channels | 200 |
| Battery Capacity (mAh) | 0 (External Power Required) |
| Display Screen | Yes |
| Maximum Range | 5km-10km |
| Is Batteries Included | No |
| Type | Car Mobile Radio |
| Output Power (w) | 10w-25w |
| Frequency Range | VHF: 136-174MHz, UHF: 400-470MHz, FM: 76-108MHz (Rx) |
| Waterproof | No |
| Material | Metal |
| Origin | Mainland China |
| Item Type | Mobile Radio |
| Certification | CE, FCC |
| Current Consumption (Receive) | 0.6A |
| Current Consumption (Low Power TX) | 1.6A |
| Current Consumption (High Power TX) | 4A |
| Current Consumption (Standby) | 0.18A |
| Current Consumption (Power-off) | 0.08A |
| Input Power | 10V (min) - 13.8V (nominal) - 15V (max) DC |
| Weight (radio body only) | 450g |
8. User Tips
- Car Installation: The compact size and included mounting bracket make this radio ideal for installation in a car.
- Power Supply: Ensure you use a stable 13.8V DC power supply. Some users have noted that a weak power supply can affect performance.
- Programming: While basic operation is straightforward, consider using the PC software for more efficient channel programming, although the software may be basic.
- Antenna & Portable Power: Note that the antenna and portable power sources are typically sold separately. Ensure you acquire compatible accessories for your needs.
- Signal Clarity: For clear modulation and long range, ensure your antenna system is efficient and your coaxial cable is of good quality.
- Dual Watch: If you experience constant clicking sounds, especially when using the Dual Watch feature, try disabling it in the settings (3.5 Double Watch).
9. Warranty and Support
For detailed warranty information and technical support, please refer to the official user manual PDF or contact the manufacturer/seller directly.
Manufacturer: Shenzhen Esma Electronics Co., Ltd
EU Representative: MARWAY Consulting UG
User Manual (PDF): A comprehensive user manual is available in PDF format. You can reference it for more in-depth instructions and diagrams. (Referenced in product details as: User manual (PDF))
9.1. FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 100 cm between the radiator and your body.
If interference occurs, try the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.