RACBOX Motorcycle Signal Lamp

Contents

RACBOX Motorcycle LED Turn Signal Light Instruction Manual

Model: Motorcycle Signal Lamp

1. Product Overview

This RACBOX Motorcycle LED Turn Signal Light is an auxiliary accessory designed for motorcycle lighting. It functions as a turn signal, brake light, and daytime running light (DRL), enhancing visibility and safety. The lights feature a high-brightness COB chip and are E24 certified, ensuring compliance with relevant automotive lighting industry standards.

Motorcycle LED Turn Signal Light with Red Brake/DRL and Amber Turn Signal Illumination

Figure 1: Motorcycle LED Turn Signal Light showcasing red brake/DRL and amber turn signal illumination.

Close-up of the LED light showing E24 certification and High-brightness COB chip

Figure 2: Close-up view highlighting the E24 certification and high-brightness COB chip.

2. Safety & Warnings

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.

3. Setup and Installation

This product features a 4-wire design for multi-functionality. LED lights require dedicated flashers for proper operation.

Installation Steps:

  1. Power Off: Turn off the motorcycle's power switch and unplug the negative terminal of the battery to prevent short circuits.
  2. Dismantle Old Lights: Carefully remove the original turn signal lights and disconnect or cut the corresponding wiring harness.
  3. Install New Lights: Align the fixed bracket of the new LED lights with the original mounting hole on your motorcycle. Securely tighten the turn signal screw (M8 / 8mm mounting bolt thread).
  4. Wiring: Connect the wires according to the diagram below. Ensure all connections are insulated and waterproofed. Note that LED lights require a dedicated flasher relay (not included) for correct turn signal function.

Wiring Diagram:

4-wire design wiring diagram for the LED turn signal light

Figure 3: Wiring connections for the 4-wire LED turn signal light.

  • Black Wire: Negative (-)
  • Red Wire: High Brightness (Brake Light)
  • White Wire: Low Brightness (DRL / Running Light)
  • Yellow Wire: Turn Signal

4. Operating Instructions

Functionality:

  • Turn Signal: The yellow wire activates the amber light for turn indication.
  • Brake Light: The red wire activates the high-brightness red light when braking.
  • DRL / Running Light: The white wire activates the low-brightness red light for continuous running light.
Visual comparison of high brightness red, low brightness red, and amber turn signal illumination

Figure 4: Illumination modes: high brightness red (brake), low brightness red (DRL), and amber (turn signal).

Testing Function:

After installation, reconnect the battery. Test the left and right turn signals, brake light, and running light functions to confirm they flash and illuminate normally. Then, reinstall any removed casings.

5. Maintenance

  • Regularly check all wiring connections to ensure they are secure and free from corrosion.
  • Keep the light lenses clean from dirt and debris to maintain optimal brightness and visibility. Use a soft cloth and mild cleaner.
  • Periodically inspect the mounting bolts for tightness to prevent loosening due to vibration.

6. Troubleshooting

  • Light Does Not Turn On: If the light does not illuminate, first check the wiring connections for proper polarity. Reverse the plug polarity if necessary. Ensure the motorcycle's power is on and the battery is charged.
  • Turn Signal Flashes Too Fast/Slow: This indicates an issue with the flasher relay. Ensure you are using a dedicated LED flasher relay, as standard relays may not be compatible with LED loads.
  • Intermittent Operation: Check for loose wiring connections or damaged insulation. Ensure waterproofing is intact to prevent moisture ingress.

7. Specifications

FeatureDetail
Brand NameRACBOX
Item TypeTurn Signal Light
Bulb TypeLED (High-brightness COB chip)
Voltage12V
MaterialAluminium + PC Lens
Housing ColorBlack
Light ColorAmber (Turn Signal), Red (Brake/DRL - High/Low Brightness)
Mounting Bolt ThreadM8 (8mm)
Dimensions (Light Body)Diameter: 21mm, Length: 34mm
Thread Length20mm
Cable Length270mm
CertificationE24 Mark
FitmentUniversal for most Dirt Bike, Street Bike, dual sport applications (e.g., Honda, Suzuki, Kawasaki, Yamaha, Hyosung, Aprilia, Buell)
Battery IncludedNo
High-concerned chemicalNone
Product dimensions diagram including light body diameter, length, thread length, and cable length

Figure 5: Detailed product dimensions.

8. User Tips

  • Many users report these lights are very good and bright, providing excellent visibility.
  • The combination of stop and turn signal functions in a single light makes them suitable for motorcycles like BMWs that use combined rear lights.
  • For regions requiring specific certifications, the E24 mark indicates compliance with European standards.

9. Warranty and Support

For any support inquiries, please contact the manufacturer or seller. The manufacturer information is as follows:

  • Manufacturer: Guangzhou Bai Ji Tun Trading Co., Ltd, C116, No. 1489, Fanghua Road Baiyun Guangzhou, tdlaccount@126.com
  • EU Authorized Representative: APEX CE SPECIALISTS LIMITED, UNIT 3D NORTH POINT HOUSE, NORTH POINT BUSINESS PARK, NEW MALLOW ROAD, CORK, T23 AT2P, IRELAND, info@apex-ce.com

An electronic version of this user manual is available for download: User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.