RACBOX LED License Plate Light Round Ground Lamp

Contents

RACBOX Universal LED License Plate Tag Lights Lamp User Manual

Model: LED License Plate Light Round Ground Lamp

1. Product Information

This manual provides instructions for the RACBOX Universal LED License Plate Tag Lights Lamp, designed for various vehicle applications.

Product Overview

The RACBOX LED License Plate Tag Light is an auxiliary accessory for automotive lighting, intended for normal replacement and upgrade of original car lights. It is suitable for a wide range of vehicles and operates on both 12V and 24V systems.

RACBOX LED License Plate Tag Lights installed on a vehicle
RACBOX LED License Plate Tag Lights installed on a vehicle, illuminating the license plate.

2. Specifications

Feature Specification
Brand Name RACBOX
Model Name LED License Plate Light Round Ground Lamp
Item Type License Plate Lights Assembly
Voltage 12 V / 24 V (10-30V)
Light Source LED
Material ABS
Case Color Black
Light Color White / Red+White
Lens Color Clear
Fitment Universal for truck, trailer, car, SUV, lorry, bus, tractor, van
Dimensions (Approx.) Length: 65mm, Width: 51mm, Height: 24mm, Thickness: 3mm
Product dimensions diagram showing length 65mm, width 51mm, height 24mm, and thickness 3mm
Product dimensions diagram.

3. Safety & Warnings

Important Safety Information: Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.
  • This product is an auxiliary accessory for automotive lighting and is only used for the normal replacement and upgrade of the original car lights, not for illegal modification or illegal use.
  • The products meet relevant national automotive lighting industry standards and have undergone strict quality testing.

4. Installation Instructions

Follow these steps carefully to install your LED License Plate Tag Lights:

  1. Turn off the vehicle engine and disconnect the power supply to avoid short circuit.
  2. Locate the mounting position of the original license plate lights assembly.
  3. Remove the fixing screws or clips that hold the stock light assembly.
  4. Unplug the power connector and take off the original license plate lights assembly.
  5. Install the new license plate lights assembly into the mounting position.
  6. Secure the light assembly with screws or clips to ensure stable installation.
  7. Connect the power plug correctly. If the light does not work, reverse the plug polarity.

Wiring Diagrams

Ensure correct wiring based on your specific light model (2-pin or 3-pin configuration).

2-pin wiring diagram showing red wire for positive and black wire for negative
2-Pin Wiring: Red wire for Positive (+), Black wire for Negative (-).
3-pin wiring diagram showing black wire for negative, yellow wire for white light, and red wire for red light
3-Pin Wiring: Black wire for Negative (-), Yellow wire for White Light, Red wire for Red Light.

5. Operating Instructions

  1. After installation, turn on the vehicle's power supply.
  2. Test all light functions to ensure normal operation (e.g., white light for license plate illumination, red light if applicable).
  3. Recheck all screws and connections to make sure they are firm and reliable.
Image showing the bright white light output of the LED license plate lamp
Bright white light output for clear visibility.
Image showing the red and white light output of the LED license plate lamp
Combined red and white light output (for models with both functions).

6. Maintenance

The RACBOX LED License Plate Tag Lights are designed for durability and require minimal maintenance. Periodically inspect the lights for any physical damage or loose connections. Clean the lens with a soft, damp cloth if dirt or grime accumulates to ensure optimal light output.

7. Troubleshooting

  • Light does not turn on:
    • Check all wiring connections to ensure they are secure.
    • Verify that the power supply is active.
    • If the light still does not work, reverse the plug polarity. LEDs are polarity sensitive and may not illuminate if connected incorrectly.
  • Light flickers or is dim:
    • Ensure stable voltage supply (10-30V).
    • Check for loose connections or damaged wires.

8. User Tips

No specific user tips were available from reviews or Q&A for this product at the time of manual creation.

9. Manufacturer & Support Information

Manufacturer

Guangzhou Bai Ji Tun Trading Co., Ltd, C116, No.1489, Fanghua Road Baiyun Guangzhou, China

Email: tdlaccount@126.com

EU Authorized Representative

APEX CE SPECIALISTS LIMITED, UNIT 3D NORTH POINT HOUSE, NORTH POINT BUSINESS PARK, NEW MALLOW ROAD, CORK, T23 AT2P, IRELAND

Email: info@apex-ce.com

Additional Resources

A detailed user manual in PDF format is available for download. You can view it here: User manual (PDF)

For any issues with delivery or product damage, a refund policy is in place. Please refer to the seller's terms for details.

© 2024 RACBOX. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.