1. Product Introduction
Thank you for choosing the INSE N3T Cordless Vacuum Cleaner. This manual provides important information for the safe and efficient use, maintenance, and troubleshooting of your new appliance. Please read it thoroughly before first use and keep it for future reference.
Key Features
- Powerful Suction: 20000Pa for effective cleaning.
- Long Runtime: Up to 40 minutes with a 2000mAh large capacity battery.
- Lightweight & Flexible: Ultra-lightweight design with a flexible LED motorized head for easy maneuverability.
- Advanced Filtration: Self-standing 5-stage HEPA filter system captures 99.99% of dirt.
- Versatile Cleaning: 6-in-1 design for various cleaning tasks on different surfaces.
Product Components
The following components are included with your INSE N3T Cordless Vacuum Cleaner:
Figure 1: INSE N3T Cordless Vacuum Cleaner and its main features.
| Item | Description | Quantity |
|---|---|---|
| ① | Main Motor | 1 |
| ② | Metal Tube | 1 |
| ③ | Floor Brush | 1 |
| ④ | 2-in-1 Brush | 1 |
| ⑤ | Clean Brush | 1 |
| ⑥ | Wall Bracket | 1 |
| ⑦ | Adaptor | 1 |
| ⑧ | Filter | 1 |
| ⑨ | HEPA | 1 |
2. Setup
2.1. Wall Mount Installation
To conveniently store and charge your vacuum, install the wall bracket:
- Choose a location near a power outlet, high enough to allow the telescopic wand and floor nozzle to hang freely.
- Place the wall mount against the wall and mark the drill holes with a pencil.
- Drill holes (with a 1/4" bit) and insert drywall anchors.
- Insert screws through the holes on the mount and tighten until firmly attached.
2.2. Assembly
Assemble the vacuum cleaner components as follows:
- Slide the telescopic tube onto the main motor until it clicks securely into place.
- Push the telescopic tube into the floor brush until it clicks.
- For cleaning high positions, accessories can be connected directly to the tube.
Figure 2: Assembly of the main components.
3. Operating Instructions
3.1. Charging the Battery
The battery is not fully charged upon delivery. Fully charge the battery before first use. General charging time is 4-5 hours.
Method 1: Wall-mounted Charging
- Place the main motor on the wall bracket.
- Connect the adapter to the main motor and plug it into a power outlet. The power indicator will flicker during charging.
Method 2: Flat Surface Charging
- Place the main motor on a flat surface.
- Connect the adapter to the main motor and plug it into a power outlet. The power indicator will flicker during charging.
Tip: To prevent the appliance from falling, it is recommended to remove the floor brush and telescopic tube and place the main motor horizontally on a flat surface for charging.
Figure 3: Wall-mounted and adapter charging methods.
3.2. Power On/Off and Cleaning Modes
- To start cleaning, press the "Power Switch" button.
- To switch between intense cleaning and energy-saving suction modes, press the "MAX" button.
- To stop cleaning, press the "Power Switch" button again.
3.3. Versatile Cleaning
The INSE N3T is designed for powerful cleaning on various surfaces and hard-to-reach areas:
- Floor Cleaning: Use the main floor brush for tile, low-pile carpets, rugs, and hardwood floors. The brush head supports 90° vertical rotation and features 4 LED lights to illuminate dust in dark areas.
- Handheld Cleaning: Detach the main motor and attach the 2-in-1 brush for cleaning furniture, car interiors, and other small areas.
- Extended Reach Cleaning: Use the telescopic tube with the 2-in-1 brush to clean high shelves, curtains, and ceilings.
Figure 4: Effective cleaning on various floor types.
Figure 5: Demonstrating the 3-in-1 multifunctionality for different cleaning needs.
3.4. Product Demonstration Video
Watch this video for a visual guide on how to use your INSE N3T Cordless Vacuum Cleaner:
Video 1: This video demonstrates the INSE N3T Cordless Vacuum Cleaner's features, including power-on, cleaning various surfaces like floors and carpets, using different attachments for sofas and keyboards, emptying the dustbin, washing the filter, and charging methods.
4. Maintenance
Regular maintenance is crucial to ensure optimal performance and longevity of your vacuum cleaner.
4.1. Daily Maintenance
Cleaning the Main Motor (Non-electrical parts):
- Turn off the vacuum cleaner before cleaning.
- Wipe the surface with a clean cloth.
- Be cautious not to get water into the inner part of the main motor.
Note: Do not place the vacuum cleaner under direct sunlight or in wet places after cleaning.
Cleaning the Detachable Roller Brush:
If the roller brush becomes tangled or stuck, an alert will appear on the LED display. Clean it promptly.
- Unlock the side lock on the bottom side of the cleaner head.
- Remove the side cover and take out the roller brush.
- Use the provided clean brush gadget to remove tangled hair and debris.
4.2. Product Maintenance
Emptying the Dustbin:
Empty the dustbin regularly to maintain constant suction. It is recommended to empty the dustbin after each use.
- Hold the cleaner over a waste basket. Press the lever to release the bottom lid of the dust cup to empty the contents.
- To remove the dust cup completely, twist it to the 'unlock' position, empty, then reattach and twist to 'lock' position.
Figure 6: Emptying the dustbin and washing filter components.
Cleaning the Plastic Filter Screen & Filter:
The advanced cyclonic filtration system efficiently captures and separates 99.99% of dirt. Regular cleaning is essential.
Figure 7: Diagram of the 5-stage cyclonic filtration system, showing High Density Sponge, Cyclone Filtration, High Efficient Filter Pad, Honeycomb Filter, and First Cyclone.
- Detach the main motor and dust cup. Remove the filter from the main motor and the filter component from the dust cup.
- Hold the strainer, rotate the filter holder, then take out the filter.
- If the filter screen and filter are dirty, wash them with cool water. Use the cleaning brush for thorough cleaning.
- Ensure all filter components are completely dry before reassembling.
Important Notes for Filter Maintenance:
- Check and clean the plastic filter screen and filter regularly.
- Clean the filter promptly if suction performance declines.
- Replace the filter if it is broken or cannot maintain suction performance.
- Do not bend or squeeze the filter.
- Do not wash the mechanical part of the dust box with water.
- Ensure the filter is correctly secured during assembly.
- Change the filter if damaged or if cleaning does not restore it to its pristine state.
5. Troubleshooting
If you encounter any issues with your vacuum cleaner, please refer to the table below for common problems and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Running time shortened | Battery life decreased. | Contact support for battery replacement. |
| Ambient temperature too high or too low. | Operate in a suitable ambient temperature. | |
| Battery not fully charged. | Charge the battery fully. | |
| No suction power | Dust cup is full. | Empty the dust cup. |
| Filter is blocked. | Clean the filter. | |
| Accessory or suction inlet is blocked. | Check for blockages and clear them. | |
| Parts not fully dried after cleaning. | Ensure all components are completely dry before reassembly. | |
| Cannot charge | Ambient charging temperature too high or too low. | Charge within the recommended temperature range (5°C-40°C). |
6. Safety Instructions
WARNING: To reduce the risk of fire, electric shock, or injury, read and follow all instructions carefully.
- Do not place the vacuum cleaner near heat sources, radiation, or burning cigarettes.
- Do not use the appliance to vacuum the following:
- All liquids such as water and solvents.
- Lime, cement, ash, and other construction dust and garbage.
- Hot objects, such as cigarette butts.
- Sharp debris, such as glass shards.
- Flammable and explosive materials, such as gasoline or alcohol products.
- Do not allow children to play with or operate the vacuum cleaner to prevent accidents.
- This vacuum cleaner is an electrical appliance; it must be used appropriately and never left unattended while operating.
- Always turn off the power during cleaning, maintenance, or when storing the vacuum cleaner.
- To disconnect power, do not pull the power cord. Grasp the plastic part of the plug to remove it from the power socket.
- Ensure the power supply voltage matches the charging voltage of the vacuum cleaner.
- Keep the power cord away from sharp objects to prevent damage.
- To prevent fires, do not immerse the vacuum cleaner in water or expose it to heating appliances or direct sunlight.
- Do not drag the power cord to move the charging station.
- If the vacuum cleaner falls and is visibly damaged, or if the power cord is damaged, do not use it. Send it immediately to an approved maintenance facility for inspection and repair.
- Stop operating the vacuum cleaner if the suction inlet is blocked to prevent damage (such as overheating) to the motor or deformation of the plastic parts due to overheating.
7. Product Specifications
Below are the technical specifications for the INSE N3T Cordless Vacuum Cleaner:
| Parameter | Value |
|---|---|
| Product Category | N3K, N3X, N3E, N3P, N3T |
| Weight (All Accessories Included) | 1.8 KG |
| Net Weight | 1.1 KG |
| Nominal Voltage | 18V |
| Nominal Power | 180W |
| Adaptor Input | 100V-240V ~ 50/60Hz |
| Battery Capacity | 2000 mAh (Li-ion) |
| Adaptor Output | 22V |
| Retractable Tube | 47/77 cm |
| Size | 43.5*28.5*18.0 cm |
| Filter Type | HEPA |
| Dust Box Capacity | 1-2 L |
| Battery Life | 40 minutes |
| Installation | Hand Held |
| Certification | CE |
8. User Tips
- For optimal performance, ensure the dustbin is emptied and filters are cleaned regularly, especially after heavy use.
- Always fully charge the battery before each use to maximize runtime.
- Utilize the different attachments for their intended purposes to achieve the best cleaning results on various surfaces.
- When cleaning under furniture, the LED lights on the floor brush are very helpful for spotting hidden dust.
9. Warranty & Support
Warranty Information:
This product comes with a 24-month warranty and lifetime customer support. The warranty applies to eligible purchases made directly from authorized distributors and covers the original owner and product. It is not transferable.
How to Initiate a Warranty Claim:
If your appliance operates improperly under normal household conditions within the warranty period, please contact customer support at support@vacservice.vip to fill out the warranty form and initiate a claim.
For additional information and detailed instructions, you may also refer to the official user manual PDF available at: User Manual (PDF).
Scan the QR code for more services and benefits.