INSE VM6

Contents

INSE VM6 Steam Mop Cleaner User Manual

Model: VM6 | Brand: INSE

INSE VM6 Steam Mop Cleaner

The INSE VM6 Steam Mop Cleaner, a versatile 10-in-1 cleaning solution.

1. Introduction

Thank you for purchasing the INSE VM6 Steam Mop Cleaner. This manual provides important safety instructions, setup guides, operating procedures, maintenance tips, and troubleshooting information to ensure safe and effective use of your appliance. Please read this manual thoroughly before first use and keep it for future reference.

Official product video demonstrating the INSE VM6 Steam Mop Cleaner's features and cleaning capabilities.

2. Important Safety Instructions

Only suitable for home use. Please read all instructions carefully before using this steam floor washer. When using the steam floor washer, the basic safety precautions should always be followed, including: Read all instructions carefully before using the steam floor washer.

⚠️ Warning

To reduce fire, electric shock or personal injury:

  • After the steam floor washer is powered on, be sure to take care of it. When the floor washer is not in use and before maintenance, the power cord must be pulled of the power socket.
  • Do not use damaged power cord or power plug. If the steam floor washer fails to work normally or falls, damages, stays outdoors for a long time or is soaked in water, please return the product to the manufacturer for after-sales inspection and maintenance. When using the steam floor washer, improper reassembly or maintenance may cause electric shock or personal injury.
  • To prevent electric shock, do not immerse the steam floor washer in water or any other liquid.
  • Do not touch the power plug or the steam floor washer with wet hands, or operate the steam floor washer with bare feet.
  • Do not use the power cord to pull the floor washer, use the power cord as a handle, clamp the power cord in the door crack or pull the power cord along the sharp edge or corner. Do not roll the steam floor washer over the power line. Make sure that the power cord is away from the heating surface.
  • Do not pull out the power plug by pulling the power cord. To unplug the power plug, grasp the power plug instead of pulling the power cord. Do not use extension wires or sockets with insufficient current carrying capacity.
  • Please unplug before maintenance.
  • Be sure to unplug the power plug when the steam floor washer is not in use.
  • When the power cord of the steam floor washer is not pulled out of the power socket, do not add water to the water tank or install the mop head of the floor washer. Pull out the power plug from the socket, wait for the machine cools down, and then add water to the steam floor washer, or disassemble the mop head of the steam floor washer.
  • Before cleaning the outside of the steam floor washer, please unplug its power cord from the power socket, and then clean the floor washer with a dry cloth. Do not spill water on the steam floor washer, or use alcohol, benzene or paint thinner to clean the steam floor washer.
  • In order to avoid circuit overload, do not operate other equipment on the socket (circuit) used by the steam floor washer at the same time.
  • To avoid scalding, please unplug the power plug of the steam floor washer and let it cool before removing or replacing the accessories of the floor washer.
  • When using, do not turn over the steam floor washer or spray steam toward people, pets or plants.
  • Do not use the product as a heating facility.
  • Be careful when using near children, pets or plants.
  • Do not add detergent, perfume, oil or other chemicals to the water used by the steam floor washer, which may damage the steam floor washer or cause unsafe use. It is recommended to use purified water as water for the steam floor washer.
  • Only use accessories recommended by merchants.
  • Do not put any foreign matter into the steam nozzle. Do not use if the steam nozzle is blocked.
  • Do not put your hands or feet under the steam floor washer. The steam will make the machine very hot.
  • Only use this product on horizontal and flat ground. Do not use on walls, counters or windows.
  • Do not use on leather, waxed furniture, synthetic fiber, velvet or other delicate, steam-sensitive materials.
  • Do not store or place the steam floor washer in a place for too long without removing the mop pad, as this may damage the ground.
  • Before removing the mop pad, pull out the power plug of the machine and let it cool.
  • Do not use the steam floor washer without a mop pad.
  • Keep the work area well lit.
  • Store the steam floor washer indoors in a cool and dry place.
  • Do not lift the steam floor washer when using it.
  • The steam ejected by the steam washer is very hot, which may cause burns. Be careful when using the steam floor washer.
  • Do not scrub any area for a long time.
  • Please do not use it on the wood floor without wax sealing or unglazed tile floor. And using a steam floor washer on the waxed floor or some floors may cause the floor to lose luster. Before starting cleaning, select an area of the surface to be cleaned for testing. Check the use and maintenance instructions provided by the floor manufacturer.
  • Be sure to select a separate area on the surface to be cleaned for testing before starting a large-scale cleaning operation. At the same time, we also recommend that you check the use and maintenance instructions provided by the floor manufacturer. the use and maintenance instructions provided by the floor manufacturer.
  • Do not use the steam floor washer without a mop pad or without adding water to the water tank. Under normal circumstances, it takes 30 seconds to generate steam. When the steam floor washer is used for the first time, the time to generate steam may be longer.
  • In order to prolong the service life of the steam floor washer, it is recommended to use pure water.

Please keep the instruction manual properly.

3. Product Overview

The INSE VM6 Steam Mop Cleaner is designed for efficient and versatile cleaning. It features a 10-in-1 design, allowing it to be used as a floor steamer and a handheld unit with various attachments. The rotating mop pads and powerful steam ensure thorough cleaning and sanitization.

Steam mop cleaning a floor, safe for family

The steam mop effectively removes germs and bacteria with super heated steam, providing a chemical-free cleaning solution.

Steam mop cleaning various floor types

Gentle on all sealed floors, tough on dirt and stubborn stains. Features washable and reusable mop pads.

Steam mop free-standing design with dimensions

Free-standing design for easy storage. Dimensions: 43.3 inches (height), 12.2 inches (width), 6.3 inches (depth).

Steam mop converts to handheld with multiple attachments

The unit converts to a handheld steamer for multi-purpose cleaning with various attachments including curved nozzle, crevice brush, small round brush, scraper head, window scraper, and big round brush.

Parts List

Diagram of INSE VM6 Steam Mop parts

Detailed diagram of the steam mop and its accessories.

  1. Handle
  2. Winding hook
  3. Telescopic rod adjustment switch
  4. Telescopic aluminum rod
  5. Steam switch
  6. Motor button
  7. Motor indicator light
  8. Steam indicator light
  9. Water tank
  10. Handle
  11. Electric rotating mop head
  12. Circular dual material mop pad
  13. Curved nozzle
  14. Big round brush
  15. Crevice brush
  16. Window scraper
  17. Scraper head
  18. Small round brush
  19. Towel set
  20. Direct nozzle
  21. Measuring cup

4. Setup and Installation

4.1. Installation of Floor Washer Handle and Telescopic Aluminum Rod

Align the semicircular notch of the aluminum rod mouth with the semicircular protrusion of the handle connector. Press the upper and lower buckles of the handle connector, align the aluminum rod mouth, and insert the circular buckles of the handle connector into the upper and lower circular holes of the aluminum rod. Press the button to pull out the handle during disassembly.

Diagram for installing handle and telescopic rod

Step-by-step guide for assembling the handle and telescopic rod.

4.2. Installation of Electric Rotary Mop Head and Circular Dual Material Mop Pad

Align the two circular mop pads with the left and right wheels respectively, and gently press them on the left and right wheels to firmly adhere.

Diagram for installing mop head and pads

Instructions for attaching the mop pads to the rotary mop head.

4.3. Connection / Disassembly of Telescopic Aluminum Rod and Main Body

Insert the snap of the telescopic aluminum rod into the fixing hole of the telescopic rod of the fuselage until a click is heard; Press the telescopic rod removal switch in the direction of the arrow in the right figure below, and pull out the telescopic aluminum rod upward to remove the telescopic aluminum rod.

Diagram for connecting/disassembling telescopic rod and main body

Guide for connecting and disconnecting the telescopic rod from the main unit.

4.4. Adjustable Product Height

The product height is adjustable from 1m to 1.2m. Pull the telescopic lever switch clockwise and release the fixing block to adjust between 1m and 1.2m at will; When it is adjusted to the ideal height for personal use, pull the telescopic lever switch anticlockwise and fasten the fixing block, then it can be used normally.

4.5. Adding Water to the Water Tank

Push the water tank push button upward to take out the water tank, unscrew the water tank cover, fill the measuring cup with water, cover the water tank cover, and install it on the main body.

Diagram for filling the water tank

Instructions for removing, filling, and reattaching the water tank.

4.6. Installation and Use of Steam Floor Washer Accessories

Align the snap of the straight nozzle with the snap hole of the main engine and insert it into the interface of the main engine. To connect other accessories, please refer to the diagram below.

Diagram for installing accessories

Visual guide for attaching various cleaning accessories.

5. Operating Instructions

5.1. Ready to Use

After the power cord is plugged in, the panel light flashes once, and the whole machine enters the standby state.

Close-up of the control panel with steam and rotation buttons

Control panel showing Steam Power Mode (Less, Normal, Large) and Rotating On/Off button.

5.2. Functional Operation Description

  1. Plug on the power supply, press the steam switch, the product starts to heat, the green light of steam selection key flashes, and the green light of the steam selection key flashes is always on after the heating is completed.
  2. Steam switch: press the steam selection key once to select the first gear steam, and the steam indicator lights green; Press twice to select the second gear steam, and the steam indicator light will be blue; Press three times to select the third gear steam, and the steam indicator lights red; Press four times to close the steam; cycle in sequence.
  3. Motor button start/stop switch: press once to start the motor, and then press one more time to turn off the motor, and cycle in sequence.
  4. The motor light is always on when the motor is working.
  5. Water shortage protection: when the PCB detects that the water tank is short of water, the heating indicator light and the steam indicator light flash 6 times in turn, and then turn off the power supply of the heater and the water pump.
  6. Press and hold the steam button for 3 seconds or press the On/Off button, and then the steam function and motor function will turn off at the same time.

Important Usage Notes:

  • HOUSEHOLD USE ONLY
  • DO NOT use outdoors or on wet surfaces
  • DO NOT immerse in water

6. Maintenance

  • Always unplug the power cord from the socket before performing any maintenance.
  • Allow the machine to cool down completely before adding water, installing/disassembling the mop head, or changing accessories to avoid scalding.
  • Clean the outside of the steam floor washer with a dry cloth. Do not spill water on the steam floor washer, or use alcohol, benzene, or paint thinner to clean it.
  • Regularly replace or clean the mop pads. If mop pads are washed with detergent, they may be damaged and need replacement.
  • Store the steam floor washer indoors in a cool and dry place.
  • To prolong the service life, it is recommended to use pure water in the water tank.
  • When storing the steam mop for a long time, remove the mop pad to prevent damage to the floor.
  • The winding hook (Part 2) easily stores the power cord.

7. Common Troubleshooting

7.1. The steam floor washer does not generate steam

  • The power plug of the steam floor washer shall be firmly inserted into the power socket.
  • Make sure the water tank is full, the power supply of the steam floor washer is connected, and the mode button is on.
  • If the indicator light is not on, try using another power outlet.
  • If the indicator light flashes, press the mode button to select the cleaning gear.
  • If the indicator light is always on, please wait 30 seconds for the steam floor washer to complete preheating.
  • If the steam floor washer still cannot generate steam after the above operation, please contact customer service.

7.2. The steam floor washer generates steam intermittently

  • If more steam is required, select the "high" mode. Please also confirm that the water tank is full.

7.3. Cleaning gear cannot be selected

  • Please ensure that the power plug of the steam floor washer is plugged into the socket and the indicator light flashes.
  • If your steam floor washer is generating steam, but the indicator light is not on, please contact customer service.

7.4. After cleaning with steam floor washer, the floor surface is dirty, with traces or spots

  • Please replace the clean mop pad. If you wash the mop pads with detergent, they may be damaged and need to be replaced.
  • Before using this product, please refer to the floor manufacturer's maintenance and repair instructions.

7.5. It is difficult to push and pull the floor washer

  • If the mop pad is not wet enough, it may be difficult to push and pull the floor washer. After a few minutes of operation, it becomes easier to push and pull the floor washer on the floor.
  • The overly dirty pad may also make the steam floor washer more difficult to push and pull. It is recommended to use a clean mop pad.

7.6. The rotating disk does not rotate or sway

  • The steam floor washer may be in an upright position. Tilt the handle down to use the washer.
  • The mop pad may be misaligned. Turn off the power, unplug the steam floor washer, wait for a while to cool the mop pad, and then reinstall the mop pad.

7.7. Vibration or swing of steam floor washer

  • The mop pad is not centered on the rotating disk. Turn off the power and unplug the floor washer, then wait for the mop pad to cool. Please follow the steps in the chapter "installation of steam floor washer" to reinstall.

8. Product Specifications

Parameter Value
Product Model VM6
Rated Voltage 120V
Rated Frequency 50/60Hz
Rated Power 1300W
Water Tank Capacity 330mL
Rotating Speed of Rotary Table 110-130 RPM
Steam Volume 16-28g/min

Hazardous Substance Restriction Identification

Name and content of hazardous substances:

Part name Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent chromium (Cr (VI)) Polybrominated biphenyls (PBB) Polybrominated diphenyl ether (PBDE)
Rubber parts (sealing gasket, rubber tube, etc.) Ο Ο Ο Ο Ο Ο
Metal structures in contact with water (boiler) Ο Ο Ο Ο Ο Ο
Heater Ο Ο Ο Ο Ο Ο
Thermal Fuse Ο Ο Ο Ο Ο Ο
Temperature controller (thermal protector) Ο Ο Ο Ο Ο Ο
Non flame retardant plastic structure (shell) Ο Ο Ο Ο X Ο
Other metal structural parts (shell, support, etc.) Ο Ο X Ο Ο Ο
Standard parts Ο Ο Ο X Ο Ο
Printed circuit board assembly (PCB board, harness, etc.) X Ο Ο Ο X Ο
  • Ο: Indicates that the content of the hazardous substance in all homogeneous materials of the component is below the limit specified in GB/T26572.
  • X: Indicates that the content of the hazardous substance in at least one homogeneous material of the component exceeds the limit specified in GB/T26572. The "X" part indicates that due to the current global technical and technological level restrictions, it is impossible to achieve a complete replacement of non-environmental substances or elements, and will be gradually improved with subsequent technical updates.
  • *: Indicates that only certain models contain such parts.

9. User Tips

Based on user feedback, here are some helpful tips for using your INSE VM6 Steam Mop Cleaner:

  • Consider Extra Mop Pads: Many users recommend purchasing additional mop pads as spares, as the included set may not be sufficient for extensive cleaning or if they wear out over time.
  • Utilize Steam Modes and Accessories: The mop offers 3 levels of steam intensity and can steam alone, rotate alone, or both. Experiment with these settings and the various attachments for different cleaning tasks and surfaces.
  • Laminate Floor Use: The mop is generally safe for laminate floors and does not leave them excessively wet. However, always perform a test on a small, inconspicuous area first, and refer to your floor manufacturer's guidelines.
  • Water Tank Capacity: The water tank has a capacity of 330ml. For larger cleaning areas, be prepared to refill the tank as needed.
  • Power Cord Length: The power cord is approximately 5 meters. For larger rooms or areas, an appropriate extension cord may be beneficial.

10. Frequently Asked Questions (FAQ)

10.1. Can I use the steam floor washer on the carpet?

No, the steam floor washer is not recommended for carpet cleaning.

10.2. What surfaces can I use the steam floor washer?

The steam floor washer is designed for all sealed hard floor surfaces. It is recommended that you first test an area on the floor to be cleaned and read the use and maintenance instructions of the floor manufacturer.

⚠️ Warning: Do not use on leather, waxed furniture, synthetic fiber, velvet or other fine materials sensitive to steam.

10.3. Can I add anything other than water to the water tank of the steam floor washer?

Do not add any cleaning solution, perfume, oil or other chemical substances to the water used for this product, as this may damage the product or make it unsafe to use. It is recommended that you use pure water in the steam floor washer.

10.4. Can I use this mop without steam and water?

The INSE VM6 is primarily designed as a steam mop. While the rotating pads can be used, its primary function and effectiveness rely on steam generation. Using it without water or steam may not yield optimal cleaning results and could potentially damage the unit if operated dry for extended periods.

10.5. Where can I find replacement mop pads or accessories?

For replacement mop pads or other accessories, please contact INSE customer support directly via email or visit their official website for authorized distributors and parts. The mop pads measure approximately 16 cm.

11. Warranty & Support

11.1. Warranty Information

This warranty term gives you specific legal rights, and you may also have other rights which vary from state to state.

12-month Warranty & Lifetime Customer Support: Only applies to eligible purchases made directly from the YOMA authorized distributors. Warranty coverage applies to the original owner and to the original product only and is not transferable.

11.2. How to Initiate a Warranty Claim

If your appliance operates improperly while in use under normal household conditions within the warranty period, please contact our customer support or visit www.yoma-lab.com to fill out the warranty form to initiate a warranty claim.

For more warranty details, please refer to www.yoma-lab.com. All rights are reserved by YOMA official website.

11.3. Activating Your 1-Year Warranty

Activate your 1 Year Warranty within one month of purchase! To activate, please send an email to support@yoma-lab.com. The email subject line should be: VM6 Warranty-US

11.4. YOMA Customer Care & Contact Details

Thank you for choosing to buy a YOMA appliance. After activating your 1 year guarantee, your YOMA appliance will be covered for parts and labour for 1 year from the date of purchase, subject to the terms of the guarantee.

If you have any queries regarding your YOMA appliance, please visit www.yoma-lab.com for online help, general tips and useful information about YOMA.

Alternatively, you can contact us by email address: support@yoma-lab.com, with details of where/when you bought the appliance.

Most questions can be solved over the email by our trained YOMA Aftersales Service staff.

Website: www.yoma-lab.com

Email: support@yoma-lab.com

A user manual in PDF format is also available for download: View User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.