1. Introduction
The Launch RF-Sensor (LTR-03 and LTR-05) is a universal replacement for Original Equipment (OE) TPMS sensors. These radio frequency sensors are designed to be programmed by Launch TPMS tools such as i-TPMS, X-431 TSGUN TPMS, CRT5011E TPMS, and Creader TPMS 5011 V2. They offer broad vehicle coverage, replacing up to 95% of OE sensors on the market, providing a convenient, economic, and powerful solution for tire workshops and individual users.
The LTR-03 and LTR-05 sensors combine both 315MHz and 433MHz frequencies into a single sensor. They feature an international leading automotive-grade chip, ensuring pressure readings are accurate to 0.1 BAR. The high-precision air valve effectively prevents air leakage, ensuring durability and stability.
LTR-05S vs. LTR-05 (Standard Version)
The LTR-05S offers several enhancements over the standard LTR-05:
- Chip Upgrade: The LTR-05S utilizes a more advanced high-performance chip, resulting in a 60% increase in programming speed.
- Programming Capability: LTR-05S supports creating up to 8 sensor IDs at once with simultaneous programming, whereas LTR-05 supports only a single sensor at a time.
- Packaging Process: LTR-05S uses a potting process for enhanced shockproof and waterproof performance, while LTR-05 uses laser welding.
- Application Scenarios: LTR-05S is better suited for large-scale repair shops, professional tire shops, and fleet management. LTR-05 is suitable for general repair shops and DIY users.
Video: Overview of Launch TPMS Sensors, highlighting features and benefits.
2. Safety Instructions
- Any maintenance or repair work must be carried out by trained experts. Incorrect installation can lead to sensor failure.
- When mounting or dismounting wheels, strictly follow the wheel changer manufacturer's operation guidelines.
- Do not exceed a drive speed of 240 km/h with the LTR-01 RF sensor mounted.
- For optimal performance, sensors must only be installed with original valves and accessories provided by LAUNCH.
- Always program the sensors using a LAUNCH-specific TPMS tool prior to installation.
- Do not install programmed TPMS sensors in damaged wheels.
- After installation, test the vehicle's TPMS according to the original manufacturer's user manual to confirm proper installation.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment generates and radiates radio frequency energy; if not installed and used according to instructions, it may cause harmful interference to radio communications. If interference occurs, try reorienting the receiving antenna, increasing separation between equipment and receiver, or connecting the equipment to a different circuit.
Battery Safety Warning
Please be aware of potential fire risks associated with the lithium-ion battery. Strictly follow the instruction manual for charging and storage. For disposal, consult your local authority's website for information on safe disposal in accordance with applicable legal requirements.
3. Setup and Installation
Components & Controls

Figure 1: LTR-05 Sensor Structure (Sensor body, Valve stem, Washer & nut, Screw, Cap)

Figure 2: LTR-05 Components (Screw, Sensor body, Valve stem rubber grommet and valve core assembly, Washer & nut, Cap)
Installation Steps
The following steps outline the process for installing the TPMS sensor. Refer to Figure 3 for a visual guide.
- Loosening the Tire: Remove the valve cap and nut, then deflate the tire. Use a bead loosener to break the tire bead. Ensure the bead loosener faces the valve.
- Dismounting the Tire: Clamp the tire on the tire changer. Adjust the valve to the 1 o'clock position relative to the tire fitting head. Use the tire tool to dismount the tire bead. Always observe this starting point.
- Dismounting the Sensor: Remove the cap and nut from the valve stem, then remove the sensor assembly from the wheel rim.
- Mounting the Sensor and Valve:
- Remove the cap and nut from the valve stem.
- Place the valve stem through the valve hole of the rim, ensuring the sensor body is located on the inside of the rim.
- Assemble the nut back onto the valve stem and tighten it to a torque of 4 Nm.
- Tighten the cap. Ensure the nut and cap are installed on the outside of the rim.
- Remounting the Tire: Place the tire on the rim, ensuring the valve starts on the opposite side of the rim from the tire fitting head. Mount the tire over the rim. Strictly follow tire changer manufacturer's instructions.

Figure 3: Visual guide for TPMS sensor installation process.
4. Operating Instructions
Programming the Sensor
Before installation, the TPMS sensor must be programmed using a compatible LAUNCH TPMS tool (e.g., i-TPMS, X-431 TSGUN TPMS, CRT5011E TPMS, Creader TPMS 5011 V2). The sensors support over-the-air wireless programming.
Cloning Old Sensor Data
The Launch TPMS sensors are 100% cloneable, eliminating the need for relearning in many cases. This process involves:
- Program the ID of the new RF-sensor to be the same as the ID of the old sensor using your LAUNCH TPMS tool.
- Install the new RF-sensor to the same wheel position as the old sensor.
- The sensor ID can often be read by the car's ECU without requiring a relearn procedure.

Figure 4: Steps for cloning old sensor data to a new Launch TPMS sensor.
5. Maintenance
- The sensor battery life is typically 4 to 6 years.
- When replacing or servicing the sensor, always use original valves and accessories provided by LAUNCH to ensure proper sealing.
- If the sensor is externally damaged, it is mandatory to replace it.
- Always tighten the valve nut to the correct torque of 4 Nm to prevent air leakage and ensure sensor stability.
6. Troubleshooting
- TPMS Warning Light On: Check tire pressure manually. If pressure is correct, verify sensor installation and programming. Ensure the sensor is not physically damaged.
- Sensor Not Detected: Confirm the sensor has been correctly programmed with a LAUNCH TPMS tool. Check for proper installation within the tire.
- Inaccurate Readings: Ensure the sensor is correctly installed and the tire is properly inflated. Physical damage to the sensor can also cause inaccuracies.
- Interference: If you experience radio interference, refer to the FCC Warning section for potential solutions.
For persistent issues, consult a qualified automotive technician or refer to your vehicle's specific TPMS system manual.
7. Specifications
Technical Parameters (LTR-03)
- Weight: <30g
- Dimension (L*W*H): Approx. 72*51*27mm
- Working Voltage: 3V
- IP Rating: IP67
LTR-03 vs. LTR-05 Comparison
| Parameter | LAUNCH LTR-03 | LAUNCH LTR-05 |
|---|---|---|
| Operating Frequency | 315MHz/433MHz | 315MHz/433MHz |
| Battery Voltage | 3.0V | 3.0V |
| RF Transmitter Power | 5~8dBm | 5~8dBm |
| Storage Temperature | -40°C~125°C | -40°C~125°C |
| Working Temperature | -40°C~125°C | -40°C~125°C |
| Dimension | 27*42*72 (mm) | 27.2*20*76.4 (mm) |
| Weight | 30g | 24g |
| IP Rating | IP67 | IP67 |
| Pressure Monitor Range | 0~800kPa | 0~800kPa |
| Pressure Reading Accuracy | ±10kPa | ±10kPa |
| Temperature Reading Accuracy | ±3℃ | ±3℃ |
Chip: World's leading FXTH87 automotive-grade chip.
8. User Tips
- Verify Your Order: Upon receiving your sensors, double-check that you have received the correct model and quantity as ordered.
- Inspect Quality: Before installation, inspect the sensors for any visible damage.
- Ensure Compatibility: Launch TPMS sensors are designed to work exclusively with Launch programming devices (e.g., Launch TSGun, I-TPMS). They are not compatible with ThinkCar or Autel devices.
- Professional Installation: If you are unsure about the installation process, it is recommended to seek professional assistance.
9. Warranty and Support
Warranty Information
The sensor is guaranteed to be free from material and manufacturing defects for a period of twenty-four (24) months or for 31,000 miles, whichever comes first. This warranty covers defects in materials or workmanship under normal use during the warranty period.
Exclusions from Warranty:
- Defects due to improper installation or usage.
- Defects induced by other products.
- Damage due to collision or tire failure.
Disclaimer of Warranties and Limitation of Liabilities
All information, illustrations, and specifications in this manual are based on the latest information available at the time of publication. The right is reserved to make changes at any time without notice. The manufacturer shall not be liable for any direct, special, incidental, indirect damages, or any economic consequential damages (including loss of profits) due to the use of this document.