Seablue a99

Contents

99 Gears 12V Spot Welder Kit Instruction Manual

Model: a99 | Brand: Seablue

1. Introduction

The Seablue a99 99 Gears 12V Spot Welder Kit is an intelligent digital display spot welder designed for efficient and precise welding of nickel sheets to 18650 lithium batteries and other cylindrical battery types. It incorporates an intelligent logic control chip for smart battery power calculation, aiming to prevent component damage. This device offers a range of features for enhanced control and safety during operation.

Key Features:

  • 99 Adjustable Power Levels: Real-time display of gear levels on digital tubes (0-99, with 1 being the lowest and 99 the highest).
  • Real-time Voltage Monitoring Protection: Displays a 'UE' alarm code if the input voltage is outside the safe range of 8-17V.
  • Real-time MOS Tube Temperature Protection: Displays a 'CE' alarm code if the MOS tube temperature exceeds 45°C.
  • High Current Capacity: Utilizes 5 MOS transistors in parallel, with a single tube capable of resisting instantaneous currents up to 300A, and a theoretical maximum peak current of approximately 1500A.
  • Durable Welding Components: Features 10AWG wire and aluminum oxide copper spot welding needles for high current carrying capacity and durability.
  • Enhanced Efficiency: Pure copper guides are integrated to significantly improve spot welding efficiency.

2. Package Contents

The standard package includes the following components:

  • Main Control Board: 1 unit
  • Welding Pen: 2 units
  • Connection Line: 2 units
  • Heat Shrink Tubing: 2 units
  • Nickel Sheet: 1 unit
  • Screws: 4 units
Spot Welder Kit Components
Image: Components included in the spot welder kit, showing the main board, welding pens, connection lines, heat shrink tubing, nickel sheet, and screws.

Note: If you purchased a 'DIY case' version, additional acrylic plates and standoffs for assembling the protective casing will be included.

3. Specifications

Parameter Value
Product Model a99
Working Voltage 12V
Working Current 100-300A
Standby Power Consumption <0.5mA
Max. Welding Thickness 0.1-0.3mm (related to battery discharge rate)
Welding Peak Current 1500A max
Voltage Requirement (Power Supply) 25Ah-60Ah or 30C or higher high rate battery
Weight 203g
Dimensions 15.00cm x 10.00cm x 4.00cm
Certification CE
Spot Welder Control Board Front and Back
Image: Front and back view of the spot welder control board.

4. Setup

It is crucial to use an appropriate power supply to ensure proper function and prevent damage to the spot welder control circuit. Choose one of the following power supply types:

  • Lead-acid battery: 12V 20-40AH. For lead-acid batteries exceeding 45AH, please consult for current limiting methods.
  • Aviation model batteries (LiPo): 3S-4S configuration. The capacity (AH) multiplied by the discharge multiplier (e.g., 60C discharge rate) should be between 100-300.
  • 12V Automotive EC5 Interface Starter Treasure: Ensure the peak current does not exceed 600A.

Prohibited Power Supplies:

Do NOT use switching power supplies, transformers, chargers, or water batteries as the power source for the spot welder. Using these will damage the control circuit.

Recommended Power Supply Types
Image: Visual examples of recommended power supplies: Lithium Battery Pack, Car Starter Battery, Model Airplane Battery, and Lead Acid Battery.

4.2. Connection Methods

CAUTION: The red soldering pens are electrically charged. Do not touch any components on the board while connected to a power source.

Battery Connection Diagram
Image: Diagrams illustrating connection methods for Lead-acid batteries and Car starter/Lithium battery packs (EC5 interface).

Lead-acid Battery Connection:

  • Connect the Input Negative terminal of the control board to the negative terminal of the lead-acid battery.
  • Connect the Input Positive terminal of the control board to the positive terminal of the lead-acid battery.
  • Connect the Output Negative terminal of the control board to the black soldering pencil.
  • Connect the Output Positive terminal of the control board to the red soldering pencil.

Car Starter / Lithium Battery Pack (EC5 Interface) Connection:

  • Connect the Input Positive terminal of the control board to the red wire of the EC5 interface.
  • Connect the Input Negative terminal of the control board to the black wire of the EC5 interface.
  • Connect the Output Negative terminal of the control board to the black soldering pencil.
  • Connect the Output Positive terminal of the control board to the red soldering pencil.

5. Operation

5.1. Spot Welding Principle

Spot welding, also known as touch welding or contact resistance welding, involves using instantaneous high current to create a high-temperature fusion in the welded metal at the contact point of the electrodes. When the electrodes are energized, and the substrate is thicker than the welding tape, more current flows through the welded joints. The contact resistance at these joints causes a dramatic temperature rise, leading to the instantaneous fusion of the welding tape and the substrate.

To achieve a stronger weld, you can either reduce the current of the welding band or increase the current to the substrate. This can be done by using thinner welding tape (less than half the thickness of the substrate) or by using notched tape.

Spot Welding Principle Diagram
Image: Diagram illustrating the spot welding principle with the control board and welding pens.

5.2. Spot Welding Technique

  1. Place the nickel sheet securely on the surface of the battery electrode to be welded.
  2. Use one welding pen to point at an angle, holding the nickel sheet in place.
  3. Use the other welding pen to lightly point up at an angle, ensuring the distance between the two pens is minimal.
  4. The control board will detect the placement of the pens and trigger the weld approximately 0.5 seconds after stable contact.
  5. If the weld appears black or the melt pool is too small on a lower gear setting, increase the gear level to achieve a stronger weld.
Welding Spot Effect Examples
Image: Examples of successful spot welds on lithium battery nickel sheets, demonstrating firm connections.

5.3. Power Adjustment

The spot welder features 99 gears for power adjustment, displayed in real-time on the digital tube. Gear '0' is the lowest setting, and '99' is the highest. Use the 'On/Off Key/Mode Key/Up Key' and 'Decrease Key' buttons on the control board to navigate and select the desired power level.

99 Gears Power Adjustment Display
Image: Digital display showing the 99 gears of power adjustment and a visual of welding pens on battery cells.

5.4. Display Working Modes

The digital display on the control board can show four different working modes:

  • d10: Increase gear display (current power level).
  • v12: Battery voltage display (real-time input voltage).
  • r10: Downshift display (for reducing power).
  • C29: MOS temperature display (real-time temperature of the MOS tubes).
Four Display Working Modes
Image: Four panels showing the different display modes: Increase gear (d10), Battery voltage (v12), Downshift (r10), and MOS temperature (C29).

6. Maintenance

To ensure the longevity and optimal performance of your spot welder, follow these general maintenance guidelines:

  • Keep the control board clean and free from dust and debris. Use a soft, dry cloth for cleaning.
  • Store the device in a dry environment, away from moisture and extreme temperatures.
  • Regularly inspect the welding pens and connection lines for any signs of wear or damage. Replace them if necessary.
  • Ensure all connections are secure before each use.

7. Troubleshooting

The spot welder is equipped with real-time monitoring to help identify potential issues. Refer to the following alarm codes:

7.1. Voltage Monitoring Protection

  • 'UE' Alarm Code: This code is displayed if the input voltage is not within the safe operating range of 8-17V.
  • Action: Check your power supply. Ensure it is a 12V source and that its voltage is stable and within the 8-17V range. An unstable or incorrect voltage can lead to poor welding performance or damage.
Real-time Voltage Monitoring Protection
Image: Diagram showing the voltage monitoring range (8-17V normal) and indicating under-voltage or over-voltage conditions.

7.2. MOS Tube Temperature Protection

  • 'CE' Alarm Code: This code is displayed if the MOS tube temperature exceeds 45°C.
  • Action: This indicates overheating. Stop welding immediately and allow the device to cool down. Ensure adequate ventilation around the control board during operation. Prolonged use at high power settings or in a hot environment can trigger this alarm.
Real-time MOS Tube Temperature Protection
Image: Visual representation of the MOS tube temperature protection, showing a thermometer icon and the 45°C threshold.

8. User Tips

  • Optimal Welding: Experiment with different gear settings to find the optimal power level for your specific nickel strip thickness and battery type. A good weld should be strong and not excessively black.
  • Clean Surfaces: Always ensure that both the battery terminals and the nickel strips are clean and free of oxidation for the best welding results.
  • Proper Pen Pressure: Apply firm but not excessive pressure with the welding pens to ensure good contact without deforming the battery or nickel strip.
  • DIY Case Assembly: If you purchased the DIY kit with an acrylic case, carefully assemble the case according to its instructions to protect the control board from accidental damage or short circuits.

9. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the seller's policies or contact the point of purchase. Keep your proof of purchase for any warranty claims.

10. Frequently Asked Questions (FAQ)

No specific FAQs are available at this time. Please refer to the troubleshooting section or contact support for assistance.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.