1. Product Overview
The diymore Model 4615 is a compact LED display module designed to indicate the capacity of various battery types, including Ternary Lithium, Lithium Iron Phosphate (LiFePO4), and Lead-Acid batteries. It operates within a voltage range of 5V to 30V and supports 2 to 8 series battery configurations, as well as 12V and 24V lead-acid batteries.
2. Setup
2.1 Wiring Instructions
The module features two wires for connection: a red wire for positive (+) and a black wire for negative (-). Ensure correct polarity when connecting to your battery or power source.
- Red Wire: Connect to the positive terminal of your battery/power source (VCC).
- Black Wire: Connect to the negative terminal of your battery/power source (GND).
The operating voltage range is DC 5V to 30V. Do not exceed this range to prevent damage to the product.
2.2 Initial Power On
Upon the first power-on, the module defaults to displaying the capacity for a 3-series ternary lithium battery. You will need to configure the module for your specific battery type and series/voltage as described in the Operating Instructions section.
3. Operating Instructions
3.1 Basic Operation
- Power On/Display: In the off state, a short press of the 'TEST' button will turn on the display and show the battery capacity.
- Automatic Turn-off: In normal display mode, if there is no button operation for 10 seconds, the display will automatically turn off to enter low power consumption mode.
- Manual Turn-off: You can manually short press the 'TEST' button to turn off the display and enter low power consumption.
3.2 Function Setting Mode
The module allows you to configure the battery type and the number of series (or voltage for lead-acid batteries). Follow these steps:
- Enter Setting State (Battery Type Selection): Long press the 'TEST' button for 2 seconds. The 'Mode light' (battery type indicator) will flash, and the 'String number light' will remain on.
- Select Battery Type: While in the setting state, short press the 'TEST' button to cycle through battery types:
- Red Light: Ternary Lithium Battery
- Green Light: Lithium Iron Phosphate (LiFePO4) Battery
- Yellow Light: Lead-Acid Battery
- Enter Series/Voltage Setting: After selecting your battery type, press and hold the 'TEST' button again for 2 seconds. The 'Mode light' will stay on, and the 'Series/Voltage light' will start blinking.
- Set Number of Strings/Voltage: Short press the 'TEST' button to cycle through the available options for your selected battery type. Refer to the table below for specific configurations.
- Save Settings and Exit: After setting the desired configuration, press and hold the 'TEST' button for 2 seconds to save the data and return to the normal battery status display. Alternatively, if no button operation occurs for 5 seconds in the setting state, it will automatically save and return to normal display.
3.3 LED Indication Display Panel in Setting Mode
Use this table to understand the LED indications for setting battery type and series/voltage:
| Mode Light | L1 | L2 | L3 | L4 | Number of Strings/Voltage |
|---|---|---|---|---|---|
| Red light (Ternary Lithium Battery) | 2 strings | ||||
| Bright | 3 strings | ||||
| Bright | 4 strings | ||||
| Bright | 5 strings | ||||
| Green light (Lithium Iron Phosphate) | Bright | 6 strings | |||
| Bright | Bright | 7 strings | |||
| Bright | Bright | Bright | Bright | 8 strings | |
| Yellow light (Lead-acid batteries) | Bright | 12V | |||
| Bright | 24V |
3.4 Video Demonstration
Watch this video for a visual guide on how to set up and configure your battery capacity indicator:
4. Maintenance
- Operating Voltage: Always ensure the input voltage is within the specified DC 5V-30V range. Exceeding this voltage will damage the product.
- Environmental Conditions: This product is not waterproof. Avoid using it outdoors or in wet environments.
- Cleaning: Keep the module clean and free from dust. Use a soft, dry cloth for cleaning.
5. Troubleshooting
- No Display/Module Not Working:
- Check the wiring for correct polarity (red to positive, black to negative).
- Verify that the input voltage is within the DC 5V-30V range.
- Ensure connections are secure.
- Incorrect Capacity Reading:
- Re-enter the setting mode and verify that the correct battery type and number of strings/voltage have been selected and saved.
- Module Damaged: If the module was connected to a voltage outside its specified range, it may be permanently damaged.
6. Specifications
| Feature | Specification |
|---|---|
| Product Model | 4615 |
| Operating Voltage | DC 5V - 30V |
| Operating Current | <10mA |
| Display Mode | LED Indicator |
| Refresh Speed | 500ms/time |
| Appearance Size | 46mm x 15mm x 3mm |
| Type | Module |
| Origin | Mainland China |
| Condition | New |
7. User Tips
No specific user tips were available from provided data. Always ensure correct wiring and configuration for optimal performance.
8. Warranty and Support
For any issues, technical support, or warranty inquiries, please contact the seller or retailer from whom you purchased this product. Please have your purchase details and product model number (4615) ready when contacting support.