Rakoncnc RCM6090

Contents

Rakon CNC Engraving Machine 6090 Instruction Manual

Model: RCM6090 | Brand: Rakoncnc

1. Product Overview

The Rakon CNC Engraving Machine 6090 is a versatile 3-axis or 4-axis wood router and engraver, designed for precision milling of various materials including wood, aluminum, plastics, and composites. This manual provides essential information for safe operation, setup, maintenance, and troubleshooting.

Rakon CNC Engraving Machine 6090

Figure 1: Rakon CNC Engraving Machine 6090

Video 1: Overview of the Rakon CNC 6090 Engraving Machine, showcasing its components and movement.

2. Safety Precautions

Hazard: Mechanical Injury

  • Never touch the cutting tool with your hands while the spindle is rotating.
  • No part of your body may enter the work area while the machine is running.
  • Protective covers or safety light curtains must be installed and must not be removed.
  • Long hair must be tied up. Never wear gloves while operating rotating equipment.

Warning: Fire Risk

  • Wood chips and dust are flammable. Smoking is strictly prohibited in the work area.
  • Fire extinguishers must be available (carbon dioxide or dry powder recommended).
  • Clean the dust collection box daily. Do not leave it overnight.
  • Do not leave the machine while the spindle is cutting at high speed.

Note: Other Hazards

  • Equipment must be reliably grounded.
  • The spindle and drive are high-voltage components. Unauthorized personnel must not open the electrical control box.
  • The dust collection hose must not be entangled in moving parts.
  • Workpieces must be reliably fixed. Processing without securing the workpiece is strictly prohibited.

3. Equipment Components

  • Bed: Cast iron structure, aluminum gantry.
  • Spindle: Water-cooled 1.5KW spindle motor (2.2kw/3.2kw optional).
  • Control System: Nc studio controller (DSP or Mach3 optional).
  • Transmission System: TBI ball screw drive for X-Y-Z axes, square rail configuration.
  • Drive Motors: Stepper System (servo motor optional).
  • Table Surface: Aluminum T-slot Table (vacuum workbench optional).
  • Accessories: Cutting tools, tool setter, clamping fixture, dust hood.
Machine Details: Table Structure, Control System, Oil Lubrication

Figure 2: Key components including table structure, control system, and oil lubrication system.

Machine Details: Stepper Motor, T-slot Table

Figure 3: Stepper motor and T-slot table details.

4. Setup Instructions

4.1. Power-On and Preparation

  1. Confirm emergency stop button is pressed.
  2. Turn on main power switch.
  3. Release emergency stop button.
  4. Turn on control computer/handheld.
  5. Open control software.
  6. Reset alarm.
  7. Start spindle cooling system (water chiller).
  8. Start vacuum cleaner (if applicable).
  9. Startup complete.

4.2. Workpiece Clamping Fixing Principles

  • Sheet metal must be clamped on all four sides or using vacuum-adhesive.
  • Temporary fixing with nails or double-sided tape is strictly prohibited.
  • Lightweight, thin sheets must be protected from vibration during cutting.

4.3. Tool Installation

  • Clean the tool holder and spindle collet (free of oil and wood chips).
  • Tool Extension Length: Just penetrate the workpiece + 3~5mm; excessive extension may break the tool.
  • Tighten the Locking Nut: Apply force with a wrench until locked; never start the machine without tightening.
  • Manually rotate the spindle to check for tool eccentricity and whether it is hitting the workpiece.

4.4. Tool Setting (Setting the Workpiece Zero Point)

  • Place the tool setting block on the workpiece surface.
  • Execute the "Automatic Tool Setting" command in the control software.
  • The system automatically records the Z-axis zero point.

Manual Tool Setting

  • X/Y Zero Point: Align the tool tip with the lower left edge of the workpiece.
  • Z Zero Point: Using a feeler gauge/tool setting block, lift the tool 0.1~0.2mm after it contacts the surface.
  • Zeroing: Set the current position as the workpiece coordinate in the software.

5. Operating Instructions

5.1. Program Loading

  • Generate toolpaths using compatible software (e.g., ArtCAM, AlphaCAM, Jingdiao, Wentai).
  • Post-process to machine tool recognition formats (.nc/.cnc/.u00/.tap, etc.).
  • Transfer to the controller via USB flash drive/network.
  • Dry Run Verification: Raise the Z-axis by 30mm, simulate operation, and confirm no collisions.

5.2. Start Machining

  • Close the safety door.
  • Reconfirm the vacuum is on (if applicable).
  • Press "Cycle Start".
  • Pay close attention to the first cut: Observe the cutting sound and whether chip removal is normal.
  • If any abnormal noise, smoke, or displacement occurs, immediately press emergency stop.

5.3. Common Errors During Operation

  • Forgetting to Lift the Tool: Starting machining directly after tool setting can cause tool collision.
  • Forgetting Material Thickness Difference: Not accounting for shim height can lead to cutting through the worktable.

6. Maintenance

6.1. Shutdown Procedure

  1. Stop the machining program.
  2. Raise the tool to a safe height.
  3. Shut down the spindle.
  4. Exit the control software.
  5. Turn off the computer/handheld.
  6. Press the emergency stop button.
  7. Turn off the main power switch.
  8. Clean the worktable and dust collection box.
  9. Apply guide rail oil.

6.2. Weekly Maintenance

  • Clean rack and pinion; apply lithium grease.
  • Check spindle cooling system (water level/air filter).
  • Inspect all bolts and fasteners for looseness.
  • Test all axis movements for abnormal noise.
  • Clean dust collector filter.

6.3. Monthly Maintenance

  • Replace cooling water (water-cooled spindle).
  • Clean or replace spindle air filter (air-cooled).
  • Check drive belt tension.
  • Inspect electrical cabinet cooling fan.
  • Verify machine leveling.

6.4. Quarterly Maintenance

  • Deep clean electrical cabinet with dry compressed air (power off).
  • Check all limit switches and sensors.
  • Inspect ball screw nuts for backlash.
  • Test ground continuity.
  • Professional inspection of spindle bearings.

7. Troubleshooting

This section covers common issues. For complex problems, contact technical support.

7.1. Common Issues and Solutions

  • Machine not powering on: Check main power switch, emergency stop button, and power connections.
  • Spindle not rotating: Verify cooling system is active, check spindle power connection and inverter status.
  • Poor engraving quality: Check tool sharpness, tool runout, workpiece clamping, and machine calibration.
  • Axis movement issues: Inspect motor connections, drive parameters, and ensure no physical obstructions.

8. Specifications

Rakon CNC 6090 Specifications Table

Figure 4: Detailed specifications of the Rakon CNC 6090.

FeatureDescription
Model NumberRCM6090
X,Y,Z Working Area600x900mm
Positioning Accuracy0.03mm
FrameCast iron structure, aluminum gantry
Table SurfaceAluminum T-slot Table
X, Y,Z axis transmissionBall Screw
Rail ConfigurationSquare rail
Spindle PowerWater-cooling 1.5KW
Spindle Speed0-24000RPM
Drive MotorsStepper System
Working VoltageAC220V/50HZ ; 60hz option
Operating SystemNc studio; DSP options
Command LanguageG code, u00, mmg, PLT, HPG
Software CompatibilityType3, Wentai (ArtCUT), ArtCAM, Aspire etc
PackingWooden case
Packing Size1520*1250*1750mm
Weight350kg
ControllerMACH3
CertificationCE

9. User Tips

  • Consider the 4th axis option for cylindrical engraving tasks to expand machine capabilities.
  • Always double-check workpiece dimensions and tool paths in the software before starting a job to prevent errors.
  • Regularly clean the T-slot table to ensure proper material clamping and prevent debris buildup.

10. Frequently Asked Questions (FAQ)

Q: Does the machine come with a 4th axis?

A: The Rakon CNC 6090 is available in both 3-axis and 4-axis configurations. The 4th axis (rotary axis) is an optional component for engraving cylindrical materials.

Q: What are the working dimensions of this machine?

A: The standard working area for the X, Y, and Z axes is 600x900mm.

11. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your vendor or Rakoncnc customer service. Ensure you have your machine model and serial number ready for faster assistance.

© 2024 Rakoncnc. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.