Diymore SH-BOOST/BUCK100J

Contents

Diymore DC 5-35V 10A Max Automatic Boost Buck High-Power Constant Voltage Constant Current LED Driver Module

Model: SH-BOOST/BUCK100J

User Manual

Introduction

This manual provides detailed instructions for the Diymore SH-BOOST/BUCK100J Boost Buck High-Power LED Driver Module. This versatile module is designed for applications requiring stable power conversion with adjustable constant voltage and constant current output. Please read this manual thoroughly before operation to ensure proper use and safety.

Diymore Boost Buck High-Power LED Driver Module DC 5-35V

Image: Diymore Boost Buck High-Power LED Driver Module (SH-BOOST/BUCK100J) with input voltage range DC 5-35V.

Features

  • High-performance boost/buck module design with efficiency up to 95%, ensuring high efficiency and low heat generation.
  • Constructed with solid materials, including 6 MOS tubes, for stable power conversion and enhanced protection.
  • Offers constant voltage and constant current output, both adjustable to suit various application needs.
  • Comprehensive protection functions: input over-current, under-voltage, backflow prevention, and short-circuit protection.
  • Equipped with multi-functional indicator lights for real-time display of operating status, providing intuitive and convenient operation.

Specifications

Parameter Value
Input Voltage Range DC 5-35V
Input Maximum Operating Current 10A MAX
Output Voltage Range DC 2.5-30V
Adjustable Output Current Range 0.1-9A
Adjustable Output Maximum Power 150W
Rated Power 120W
Typical Efficiency 95% (90%-97%)
Operating Frequency 200KHZ
Output Constant Voltage Indicator Blue
Output Constant Current Indicator Red and Blue
Battery Full Indicator Light Green
Battery Near Full Indicator Light Blue and Green
Heat Dissipation Heat Sink (included)

Product Dimensions

Product dimensions: 90.8mm length, 52.8mm width, 20mm height

Image: Module dimensions showing approximately 90.8mm (3.57in) length, 52.8mm (2.07in) width, and 20mm (0.78in) height.

Setup

Package Contents

  • 1x Boost Buck High-Power LED Driver Module
  • 1x Heat Sink

Connections

Refer to the wiring diagram below for proper connection of input and output terminals.

Top and bottom view of the module, showing input and output terminals

Image: Top and bottom views of the module, highlighting the IN+ (input positive), IN- (input negative), OUT+ (output positive), and OUT- (output negative) terminals.

  • Input: Connect your DC 5-35V power source to the IN+ (positive) and IN- (negative) terminals.
  • Output: Connect your load (e.g., LED, battery for charging) to the OUT+ (positive) and OUT- (negative) terminals. The output voltage range is DC 2.5-30V.

Heat Dissipation

The module includes a heat sink. For high-power applications or extended use, ensure adequate ventilation or consider additional cooling measures to prevent overheating.

Module with included heat sinks

Image: The module shown with the separate heat sinks provided for installation.

Operating Instructions

Wiring and Function Diagram

Wiring and Function Diagram of the Boost Buck Module

Image: Detailed wiring and function diagram, indicating input/output terminals, voltage/current adjustment potentiometers, and indicator lights.

Output Voltage Adjustment

The output voltage is adjusted using the voltage adjustment potentiometer. Turn the potentiometer counterclockwise to lower the voltage, and clockwise to raise the voltage.

Output voltage adjustment potentiometer

Image: Close-up of the module highlighting the output voltage adjustment potentiometer.

Output Current Adjustment

There are two methods for adjusting the output current:

  1. Method 1 (Short-Circuit Method):
    • First, adjust the output voltage to approximately 5V.
    • Turn the current adjustment potentiometer counterclockwise to its minimum position.
    • Use the current measurement function of a multimeter to short-circuit the output terminals and adjust the short-circuit current.
    • Important: When using this method, ensure the input voltage remains above 8V for more accurate results.
  2. Method 2 (Constant Current Load Method):
    • First, adjust the output current to the voltage required by your constant current load (typically, the no-load output current of the power supply should be about 3V higher than the output current required by the load).
    • Turn the current adjustment potentiometer counterclockwise to its minimum position.
    • Connect the constant current load.
    • Adjust the current to the level required by the load.

Indicator Lights

  • Output Constant Voltage Indicator: Blue light. This light is on when the module is operating in constant voltage mode.
  • Output Constant Current Indicator: Red and Blue lights. Both lights are on during constant current output.
  • Battery Full Indicator Light: Green light. This light indicates the battery is fully charged.
  • Battery Near Full Indicator Light: Blue and Green lights. Both lights are on when the battery is nearly fully charged.

Product Overview Video

Video: A brief overview of the Diymore Boost Buck High-Power LED Driver Module, showcasing its physical appearance and key components.

Maintenance

  • Keep the module clean and free from dust and debris.
  • Ensure proper ventilation, especially during high-power operation, to prevent overheating.
  • Avoid exposing the module to moisture or extreme temperatures.
  • Regularly check connections for tightness and signs of corrosion.
  • Do not attempt to modify the module unless you are a qualified electronics technician.

Troubleshooting

  • No Output: Check input power supply, ensure connections are secure, and verify input voltage is within the specified range (DC 5-35V).
  • Incorrect Output Voltage/Current: Re-adjust the respective potentiometers carefully. Ensure your multimeter is correctly set for voltage or current measurement.
  • Overheating: Reduce load, ensure proper heat sink installation, and improve ventilation.
  • Indicator Lights Not Functioning: Verify the module is powered and under load conditions that would trigger the indicators (e.g., constant current mode for red/blue, battery charging for green/blue-green).

User Tips

  • When adjusting current, especially using the short-circuit method, it's advisable to use a current-limiting power supply for safety.
  • Always double-check polarity before connecting power to avoid damage to the module or connected devices.
  • For precise adjustments, use a high-quality multimeter.
  • Consider mounting the module in an enclosure that allows for good airflow to maximize its lifespan.

Warranty and Support

For detailed warranty information and technical support, please refer to the official product documentation or contact the seller directly. A comprehensive user manual in PDF format is available for download:

View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.