1. Introduction
This manual provides essential information for the safe and efficient use of your Diymore DC-DC High Voltage Step-Down Power Module. This module is designed to convert high DC input voltages (up to 120V) into stable lower DC output voltages (3.3V, 5V, or 12V), making it suitable for various electronic projects, GPS systems, and microcontroller power supplies.
Video: Overview of the Diymore DC-DC Step-Down Power Module.
2. Safety Information
WARNING: Electrical Shock Hazard
- Always ensure power is disconnected from the input source before making any connections to the module.
- High voltages can be dangerous. Exercise extreme caution when working with high-voltage power supplies.
- Do not touch the module or its connections when power is applied.
- Ensure proper insulation and avoid short circuits.
- This module is intended for use by individuals familiar with electronics and electrical safety practices.
3. Setup and Wiring
The module features clearly labeled input and output terminals for straightforward connection.

Image: Front and back view of the module showing IN+, IN-, OUT+, OUT- terminals. The module supports 48V, 60V, 120V high-voltage inputs and provides 3.3V/5V/12V outputs.

Image: Detailed wiring diagram for the DC-DC 8~120V step-down module. Connect positive input to IN+, negative input to IN-, positive output to OUT+, and negative output to OUT-. Output voltage options are 12V/5V/4.2V/3.3V with a maximum current of 1A.
Connection Steps:
- Identify Terminals: Locate the IN+ (Positive Input), IN- (Negative Input), OUT+ (Positive Output), and OUT- (Negative Output) terminals on the module.
- Connect Input: Connect your high-voltage DC power source to the IN+ and IN- terminals. Ensure correct polarity.
- Connect Output: Connect your load (e.g., microcontroller, GPS unit) to the OUT+ and OUT- terminals. Ensure correct polarity.
Important Precautions:

Image: Precautionary note. Always connect the module to the power supply before applying power. Connecting the module while the input is live can cause sparks and damage, especially with high input voltages.
- Always connect the module to the power supply BEFORE applying power.
- Connecting the module while the input is live can easily cause sparks, especially if the input voltage is high. This can potentially burn the module's solder pads or damage components.
- Double-check all connections for correct polarity before powering on.
4. Operating Instructions
Once properly wired, the module will step down the input voltage to the selected output voltage. The specific output voltage (3.3V, 5V, or 12V) is determined by the variant of the module you have purchased.

Image: Example of a 3.3V output variant of the module.
- Stable Current Output: The module provides a maximum output current of 1A. Its low quiescent current makes it suitable for long-term standby operations.
- High Efficiency: Designed for high conversion efficiency with low heat generation, ensuring stable and reliable operation.
5. Maintenance
- Keep the module clean and free from dust and debris.
- Avoid exposing the module to moisture or extreme temperatures.
- Regularly inspect connections for any signs of corrosion or loose wiring.
- Do not attempt to repair the module if damaged; replacement is recommended.
6. Troubleshooting
- No Output Voltage:
- Check input power supply: Ensure it is connected and providing the correct voltage within the specified range.
- Check wiring: Verify all connections are secure and correctly polarized.
- Check for short circuits: Ensure there are no short circuits on the output.
- Incorrect Output Voltage:
- Verify the input voltage is within the specified range for the desired output.
- Ensure the load current does not exceed the maximum 1A output.
- Module Overheating:
- Ensure adequate ventilation around the module.
- Verify the output current does not exceed 1A.
- Check for any short circuits or excessive load.
7. Specifications

Image: Module dimensions: 24mm (0.94in) x 18mm (0.71in).
| Parameter | Value |
|---|---|
| Module Type | DC-DC Non-Isolated Step-Down |
| Operating Frequency | 140KHz |
| Max Input Voltage | 120V |
| Output Voltage (12V variant) | 12V (Input: 16V-120V) |
| Output Voltage (5V variant) | 5V (Input: 8V-120V) |
| Output Voltage (4.2V variant) | 4.2V (Input: 8V-120V) |
| Output Voltage (3.3V variant) | 3.3V (Input: 30V-120V) |
| Max Output Current | 1A |
| Dimensions (L x W) | 24mm x 18mm (0.94in x 0.71in) |
| Protections | Built-in over-temperature protection, output short-circuit protection |
8. User Tips
- For optimal performance and longevity, ensure the module is operated within its specified input voltage and output current limits.
- Consider using heat sinks if operating at the upper limits of current or in high ambient temperatures, although the module is designed for good heat dissipation.
- Always test the output voltage with a multimeter before connecting sensitive electronics.
9. Warranty and Support
For any issues or support inquiries, please contact the seller or manufacturer. Keep your purchase records for warranty claims.