1. Introduction
The VDIAGTOOL V500 Pro Automotive Intelligent Electrical System Circuit Tester Breaker Finder Tool is the newest generation intelligent tool with a 2.36-inch large LCD screen display. It is dedicated to testing all 9V-30V vehicle electrical systems.
The V500 Pro is an upgraded version of V500, adding a Short Open Circuit Finder. This tool allows you to quickly and easily locate open circuits, open connections, broken wires, current leaks, and trace wires. It can also help find intermittent circuit problems by flexing wires or connectors and listening for a change in the receiver tone. This professional Short Open Circuit Finder works on circuits with voltages between 6 and 42 volts DC, suitable for automobiles, trucks, tractors, boats, RVs, and more.

Figure 1: VDIAGTOOL V500 PRO Kit Overview
2. Safety Information
To ensure your safety and prevent damage to the device or vehicle, please carefully read and follow all instructions in this manual before use.
When operating the device, always verify proper testing procedures and strictly adhere to the instructions provided. As automotive electrical systems may vary, you must assess potential risks and ensure a safe testing environment.
Always observe all safety warnings, use appropriate tools, and disconnect power sources when necessary. Improper operation may result in personal injury, equipment damage, or voided warranty.
Safety Messages
Safety messages use standardized signal words to indicate hazard levels and prevent injuries or equipment damage:
⚠️ DANGER
Will result in death or serious injury if ignored
Indicates an immediately life-threatening hazard.
⚠️ WARNING
Could result in death or serious injury if ignored
Indicates a potentially dangerous situation.
Safety Instructions
This manual covers known safety hazards, but cannot anticipate all possible risks. You are responsible for ensuring safe operating conditions and procedures.
⚠️ DANGER
- Always ventilate the service area when the engine is running or use a building exhaust removal system if available.
- Carbon monoxide is odorless and deadly - it can cause loss of consciousness or death.
⚠️ WARNINGS
- Always keep a fire extinguisher suitable for gasoline, chemical, and electrical fires nearby.
- Never operate or observe the tool while driving—distraction can lead to fatal accidents.
- Keep clothing, hair, hands, tools, and test equipment away from moving or hot engine parts.
- Perform automotive testing only in a safe, controlled environment.
- Ensure proper ventilation—exhaust gases are poisonous.
- Never connect or disconnect test equipment while the ignition is ON or the engine is running.
- Place wheel chocks in front of drive wheels and never leave the vehicle unattended during testing.
- Wear ANSI-approved safety eye protection at all times.
- Exercise extreme caution around ignition coils, distributor caps, spark plugs, and wires—high voltage is present when the engine is running.
- Before testing, ensure the transmission is in P (A/T) or Neutral (M/T) and the parking brake is engaged.
- Keep the scan tool clean and dry; avoid contact with oil, water, or grease. Clean only with a mild detergent and soft cloth.
- Do not modify, disassemble, or expose the tool to extreme temperatures or moisture.
- This tool is not a substitute for professional diagnostic equipment—use with caution.
- The manufacturer is not liable for damages caused by misuse, negligence, or unauthorized modifications.
3. Product Overview (Components)
The V500 PRO tool consists of several key components designed for comprehensive automotive electrical testing. Refer to the diagram below for component identification.

Figure 2: V500 PRO Components
- Probe Tip: Contact the circuit or component for testing.
- Front LED Light: Used for lighting in dark working areas.
- LCD Screen: Displays test results and can be folded up to 90° for viewing at different angles.
- Red/Green LED Indicator: Indicates positive (Red) and negative (Green) polarity.
- Key Button Operation: 6-Key navigation for fast operation.
- Red Positive Wire: Used to deliver current.
- Auxiliary Ground Lead: Auxiliary clip of ground lead.
- USB Port: For device updates via PC connection.
- Relay Test Port: Connect the relay test cable.
- Speaker: Buzzer for warning or reminders.
- Antenna: Receives data for the Breaker Finder.
- Buzzer: Provides sound prompts.
- Sensitivity Controller: Adjusts the sensitivity for the Breaker Finder.
- Test Button: Press to start testing.
- Headphone Port: For external headphones.
- Fuse: Protects the device from damage due to overload.
- Tool Kit Working Mode Switch: Switches between Circuit Tester and Breaker Finder modes.
Accessories Included:
- V500 Pro Circuit Tester × 1
- V500 Pro Breaker Finder × 1
- Probe Tip × 1
- Fine Probe Tip × 1
- Relay Test Cable × 1
- Alligator Battery Clip × 1
- Clip line: OD 4.5mm, Length 0.4m
- Relay line: OD 4.0mm, Length 0.5m
- Probe Tip Extension Cable × 1
- Wire Piercing Probe × 2
- Banana to Banana Plug Test Lead × 2
- Fuse × 3
- Type-C Data Cable × 1
- User Manual × 1
4. Setup
The V500 PRO Circuit Tester is powered by connecting directly to the car battery (9V-30V DC). The V500 PRO Breaker Finder requires a 9V battery (not included) for operation.
- Connect the red alligator clip (positive) to the vehicle's positive battery terminal.
- Connect the black alligator clip (negative) to the vehicle's negative battery terminal or a good chassis ground.
- Ensure all connections are secure before proceeding with any tests.
- For the Breaker Finder, ensure a 9V battery is installed.
5. Operating Instructions
5.1 Keypad Introduction
The device features a 6-key navigation system:
- ESC button: Returns to the previous screen. For other tests, press ESC button once to exit.
- OK button: Confirm key.
- Up button: Navigation key or voltage output, numerical adjustment.
- Left button: Navigation key.
- Right button: Navigation key.
- Down button: Navigation key or voltage output, numerical adjustment.
5.2 Smart Test
This feature includes Voltage Test, Resistance Test, and Positive/Negative Test. It automatically recognizes the measured signal and displays voltage or OHM values without switching modes.
- Voltage Test: When the probe clip (auxiliary ground lead) is connected to the ground wire, the probe automatically enters voltage display mode when a voltage signal is detected on the Probe Tip. The screen displays the test voltage (VDC) and battery supply voltage (VCC).
- Resistance Test: Connect the probe clip (auxiliary ground lead) to one end of the resistance and the Probe Tip to the other end. The probe automatically enters resistance display mode and shows the resistance value.
- Positive/Negative Test: If the probe detects a voltage deviation of ±0.8V from the power supply, the RED LED lights ON for positive signals, and the GREEN LED lights ON for negative signals. The speaker will sound regularly.
5.3 Multimeter Mode
This mode allows for high-efficiency measurement of various electrical parameters. Use the 'Left' or 'Right' buttons to select the test mode.

Figure 3: Multimeter Mode Interface
- Voltage (VDC): Connect the probe clip (auxiliary ground lead) to the negative pole, and the probe tip to the measured voltage.
- Resistance (OHM): Connect the probe clip (auxiliary ground lead) to one side of the resistance being measured, and the probe tip to the other side.
- Diode (DIO): Connect the probe clip (auxiliary ground lead) to one side of the Diode being measured, and the probe tip to the other side. It will display the voltage and show the positive and negative of the Diode.
- Current (AMP): The probe is connected in series in the circuit under test; it will display the current value. NOTE: When testing the current, ensure wires are in series, not parallel, to avoid overload protection and device restart.
- Frequency (HZ): Displays the frequency of the measured signal and duty cycle value.
- Polarity (P-N): Displays whether the current measured line is positive or negative.
5.4 Oscilloscope Mode
This feature is an electronic test instrument that displays electrical signals graphically, usually as Voltage (vertical or Y axis) versus Time (transverse or X axis). This function can be displayed in vertical or transverse screen.

Figure 4: Oscilloscope Mode Interface
The Voltage on the Y axis shows 0.0V to 10.0V and the Time on the X axis shows 1ms to 500ms. Press the "OK" button to pause or run waveform refresh.
5.5 0-5V Power Supply
This feature provides a regulated and stable 0-5V DC output voltage, commonly used to power low-voltage electronic devices like micro-controllers, sensors, and LED lights.

Figure 5: 0-5V Power Supply Interface
NOTE: The 0-5V Power Supply is an active mode that can adjust the voltage output under 5V and limit the current to 100mA. This is a safety feature to avoid burning out electric components.
5.6 Component Activation
This feature verifies the input/output behavior of a test object, ensuring its functionality. It allows fast activation of components on your hand or in the vehicle.

Figure 6: Component Activation Interface
It has three activation modes:
- "MOMENT" Mode: Press 'Left' or 'Right' to select. Hold 'UP' or 'Down' to supply power, release to stop.
- "LATCH" Mode: Press 'UP' or 'Down' to supply power, press again to stop.
- "PULSE" Mode: Press and hold 'UP' or 'Down' to supply power, release to stop.
- "SETTING" Circuit Breaker: Press 'UP' or 'Down' to adjust overload current values from 1A - 18A.
⚠️ WARNING: Importance of Component Activation
- The activation mode is only designed for supplying power or ground. It cannot be used for sensitive electronics equipment (such as ECU, sensor modules), as this risks burning out components.
- Do not perform any tests on any ECU module or SRS (airbag) system before the system is completely disabled or unplugged.
- Supplying power to the electrical system can damage the vehicle's sensitive electronic components. Always refer to the vehicle manufacturer's schematic diagram and diagnostic process.
5.7 Relay Test
This feature reviews protective devices in a system, ensuring the proper operation of protective relays. The interface displays the power supply voltage (VCC) and shows diagrams for 4-terminal and 5-terminal automotive relays.

Figure 7: Relay Test Wiring Examples
Press the "UP" button to start the test and "OK" button to view the wiring connection diagram for these two different relays.
5.8 Fuel Injector Test
This feature uses the probe tip to output different pulse signals to the injector and check its spraying status, helping diagnose injector conditions.
Procedures:
- Turn off the vehicle's engine.
- Connect the BLACK clip to the negative terminal of the battery and the RED clip to the positive terminal.
- Unplug the connector from the fuel injector. Connect the probe auxiliary ground lead to the negative side of the injector, and the probe tip to the positive side.
- After entering the Injector Test function, select the desired test mode (M1, M2, M3, or M4).
- Press the "OK" button to trigger the test.
- Check the injector spraying status to diagnose the condition.
There are 4 Signal Output Modes:
- M1: Outputs 1 pulse with a positive pulse width of 250ms.
- M2: Outputs 7ms positive, then 20ms negative, cycle 1.4s.
- M3: Outputs 4ms positive, then 10ms negative, cycle 1.4s.
- M4: Continuously outputs positive for 7ms, then negative for 20ms. Press "ESC" to stop.
5.9 Locating Open Circuit / Breaker Finder
The probe of the breaker finder is built of coiled steel and can be bent as needed to reach wires in congested or difficult areas. The probe picks up the signal from the wire in a range of positions, depending on circuit characteristics and sensitivity settings.
For the best range, the Breaker Finder's probe tip (black cap) should be positioned perpendicular (at 90°) to the wire being traced, either above or below it.
Setting Sensitivity Level: To increase sensitivity, turn the rotary switch of the circuit breaker finder clockwise. To decrease sensitivity, turn the rotary switch anticlockwise.
Operation Guide:
- With the probe kit connected to power, select Mode II on the tool kit working mode switch button.
- Switch on the Short Open Circuit Finder and set the rotary switch to the middle position.
- Press and hold the TEST button, and move the black probe tip along the wire you want to test. The finder detects the signal and sounds the loudspeaker, indicating correct operation.
- Connect the black test lead to the negative supply (ground) and the red test lead to the positive supply (or a fuse socket for convenience).
- Switch on the finder probe and set its rotary switch to the middle position. Press and hold the TEST button and slowly sweep the wire with the probe point above or below perpendicularly and as close as possible. Check at different points of the wire to narrow it down or trace the wire all along, moving towards the end with the load.
- Observe the tone signal. Where the tone signal stops, it indicates the location of an open, break, or bad connection in the circuit.
- If it's difficult to pick up any tone signal, increase the sensitivity by turning the rotary switch clockwise and test again.
- Once the open circuit is located, disconnect the test leads and release the TEST button.
5.10 Locating Short Circuits
Short circuits often appear as a blown fuse, a tripped fusible link, or an electrical protection device tripping (e.g., a circuit breaker). This is the best place to begin the search.
Test Procedure:
- Remove the blown fuse from the fuse box.
- Use the probe tip to activate and energize each of the fuse contacts.
- The contact which trips the circuit breaker is the shorted circuit. Note this wire's identification code or color.
- Follow the wire as far as possible along the wiring harness.
- If the circuit breaker trips, you have verified the shorted wire.
- Cut the wire and energize each end with the probe tip. The wire end which trips the circuit breaker again is the shorted circuit and will lead you to the shorted area.
- Follow the wire in the shorted direction and repeat this process until the short is located.
5.11 Checking for Bad Ground Contacts
Test Procedure:
- Enter into Active mode, select MOMENT mode function, and set the overload current to 1A.
- Connect the probe tip to a suspected ground wire or contact.
- Press the "OK" button to trigger the power supply.
The RED LED light will turn ON, and the LCD screen will display VDC, AMP, and VCC values. If the VDC value is almost the same as VCC and the AMP value is minimal (approaching 0A), it means this is not a true ground. Otherwise, if the probe circuit breaker trips or displays OVERLOADED, it is likely a good ground.
Keep in mind that high current components, such as starter motors, will also trip the circuit breaker.
5.12 Trailer Lights and Connection Test
When the probe is in Multimeter or SMART test mode, connect the probe auxiliary ground lead to the trailer light, and insert the probe tip into the OBD socket to display the current voltage. This method allows you to check the function and direction of the connector and trailer lights. If the trailer light connection is correct, you can use the "Component Activation" function to test whether the trailer light is working.
6. Settings
6.1 Language
There are nine languages to choose from: English, Simplified Chinese, French, Spanish, German, Russian, Italian, Portuguese, and Polish.
6.2 Floodlight
You can turn the headlight of your device on or off.
6.3 Voice
You can turn the sound of the device on or off.
6.4 Self Test
- LCD Test: Displays different colors to check screen functionality and for black spots.
- Key Test: Displays buttons on screen. Pressing a corresponding button makes its symbol flash once.
- LED Test: The floodlight and positive/negative LED lights remain on, indicating proper function.
6.5 Display Mode
Choose between Light mode or Dark mode for the device display.
6.6 Update
To update the device, hold down the 'Down' key and power on the device. The device will display "USB mode", allowing you to use the computer software to upgrade the device.

Figure 8: Update Screen
7. Troubleshooting
If the probe circuit breaker trips, it indicates an overload. This can occur due to:
- The contact being probed is a direct ground or negative voltage.
- The component being tested is short-circuited.
- The component is a very high current component (e.g., a starter motor).
If the probe restarts after the circuit breaker trips or the LCD screen displays "OVERLOADED", you can adjust the overload current value (1A-18A in Component Activation settings) and repeat the operation. To prevent component damage, always refer to the component's specifications and parameters before setting the OVER-LOAD CURRENT VALUE.
If you are contacting a protected circuit, applying ground to it may cause the vehicle fuse to burn out or the probe to trip.
8. Specifications
| Parameter | Circuit Tester | Breaker Finder |
|---|---|---|
| Display | LCD Display | N/A |
| Operating Voltage | 9V - 30V DC | 6V - 42V DC |
| Voltage Measurement Range | 0.1V - 100V | N/A |
| Resistance Measurement Range | 0KR - 200KR | N/A |
| Operating Temperature | 0°C - 50°C (32°F - 122°F) | 0°C to 60°C (32°F to 140°F) |
| Storage Temperature | -20°C - 70°C (-4°F - 158°F) | -40°C to 70°C (-40°F to 185°F) |
| Working Environment Temp | 0°C - 50°C (32°F - 122°F) | N/A |
| Power Source | By Connecting to Car Battery | By a 9V Battery |
| Main line (Length) | 6m | N/A |
| Extension line (Length) | 1m | N/A |
| USB line (Length) | 0.5m | N/A |
9. User Tips
- Ensure the Breaker Finder has a fresh 9V battery installed for optimal performance, as it is not powered by the car battery like the Circuit Tester.
- When using the Short Open Circuit Finder, if you encounter difficulty picking up a tone signal, try increasing the sensitivity by turning the rotary switch clockwise.
- Always double-check the vehicle's electrical diagrams before activating components to avoid damage to sensitive electronics.
10. Warranty & Support
Limited Three Years Warranty
VDIAGTOOL warrants the V500 Pro product against defects in materials and workmanship for thirty-six (36) months from the date of delivery to the original purchaser for commercial or business use. This warranty does not cover damage resulting from misuse, unauthorized modification, improper maintenance, or operation outside specified conditions. VDIAGTOOL's sole liability shall be limited to repair or replacement of defective components at its discretion. Consequential, incidental, or other damages are expressly excluded. Some jurisdictions may not permit certain limitations of liability.
Technical Support
- Official Website: www.vdiagtool.com
- Support Email: support@vdiagtool.com
- US Hotline: +1-213-355-7171
- Online Form: https://www.vdiagtool.com/support/tech-support
Training Videos
Free product operation videos are available:
- Visit Training Center: https://www.vdiagtool.com/support/training-center
- Select the "Circuit Testers" category, then watch model-specific tutorials.
Video 1: VDIAGTOOL V500 PRO Product Demonstration
11. Contact Information
For Wholesale Business or to Become a Distributor:
- Email: sales@vdiagtool.com
For Product Development and Testing (Inventors):
- Email: inventers@vdiagtool.com
Social Media:
Follow VDIAGTOOL on social media for updates and community interaction:
- Facebook Page: Search for "vdiagtool"
- Facebook User Group: Search for "VDIAGTOOL OFFICIAL User Group"
- Instagram: Search for "vdiagtool_official"
- TikTok: Search for "vdiagtool_us"
- YouTube: Search for "Vdiagtool Official"
For the latest documentation, visit: https://www.vdiagtool.com/support/downloads
A user manual in PDF format is available for download: User manual (PDF)