DRAGON GAUGE 5041B

Contents

2" 52mm Car Boost Meter Instruction Manual

Model: 5041B

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your 2-inch (52mm) Electronic Boost Gauge. This gauge is designed to accurately measure and display the boost pressure in your vehicle's engine, featuring an alarm function and a customizable 7-color backlight. It is suitable for universal 12V car applications.

Safety Information

  • Always disconnect the vehicle's battery before performing any electrical work to prevent short circuits and electrical shock.
  • Ensure all wiring connections are secure and properly insulated to prevent hazards.
  • Mount the gauge in a location that does not obstruct your view of the road or interfere with vehicle controls.
  • If you are unsure about any installation steps, consult a qualified automotive technician.

Package Contents

Please check the package for the following items:

  • 1 x Boost Gauge (PSI or Bar version)
  • 1 x Boost Sensor
  • 1 x PVC Hose (6 Feet)
  • 1 x T-Fitting
  • 1 x Wiring Harness
  • 1 x English Instruction Manual
Package contents of the boost gauge

Image: Contents of the boost gauge package, including the gauge, sensor, hose, T-fitting, wiring, and manual.

Setup

1. Mounting the Gauge

  • Select a suitable location on your dashboard or A-pillar that provides clear visibility without obstructing your driving view.
  • Ensure there is enough space behind the mounting location for the gauge body and wiring connections.
  • Drill a 52mm (2-inch) hole if flush mounting, or use a suitable gauge pod (not included).
  • Secure the gauge firmly in place.

2. Wiring Connections

Refer to the wiring diagram below for proper electrical connections. Ensure the vehicle's battery is disconnected before proceeding.

Wiring diagram for boost gauge

Image: Electrical installation instructions for various gauges, highlighting the Boost/Vacuum Gauge wiring.

  • Red Wire: Connect to a switched 12V ignition source (e.g., IGNITION SWITCH 12V(+)). This ensures the gauge powers on and off with the vehicle.
  • Black Wire: Connect to a reliable chassis ground (e.g., BATTERY(-)).
  • Green Wire: Connect to the signal wire from the Boost Sensor.

3. Boost Sensor and Hose Installation

  • Locate a suitable vacuum/boost line on your engine (e.g., from the intake manifold).
  • Cut the vacuum/boost line and insert the supplied T-Fitting.
  • Connect one end of the PVC Hose (6 feet) to the T-Fitting.
  • Connect the other end of the PVC Hose to the Boost Sensor.
  • Mount the Boost Sensor securely in a location away from excessive heat or vibration.
  • Ensure all hose connections are tight to prevent leaks, which can affect gauge accuracy.

4. Initial Power-Up

Once all connections are made, reconnect the vehicle's battery. Turn the ignition to the 'ON' position (without starting the engine). The gauge should illuminate and perform a self-test sweep. Start the engine and observe the gauge's readings.

Operating Instructions

1. Reading the Gauge

The gauge displays boost pressure in either PSI or Bar, depending on the model purchased. The needle indicates the current pressure. Negative values (left side of 0) typically indicate vacuum, while positive values (right side of 0) indicate boost.

PSI and Bar boost gauges

Image: Examples of the boost gauge displaying in PSI and Bar units.

2. Changing Backlight Colors

The gauge features 7 selectable backlight colors. To change the color, locate the button on the gauge face or side (refer to your specific gauge model for exact button location). Pressing this button will cycle through the available colors.

Boost gauge showing 7 backlight colors (PSI)

Image: The boost gauge illuminated in various backlight colors (PSI version).

3. Alarm Function

The gauge is equipped with an alarm function to alert you when boost pressure exceeds a preset limit. When the pressure reaches the alarm threshold, the gauge will flash a red light to indicate an over-boost condition.

Boost gauge alarm indication

Image: PSI boost gauge with an arrow pointing to the red alarm lights, indicating the alarm function.

The factory-set alarm range is -1.3~2 Bar / 20~30 PSI. Consult the detailed PDF manual for instructions on adjusting the alarm threshold if applicable.

Maintenance

  • Cleaning: Use a soft, damp cloth to clean the gauge face. Do not use abrasive cleaners or solvents, as they may damage the display.
  • Connection Check: Periodically inspect all electrical and hose connections to ensure they are secure and free from corrosion or damage.
  • Hose Inspection: Check the PVC hose for any signs of cracking, kinking, or leaks, especially in areas exposed to engine heat or movement. Replace if necessary.

Troubleshooting

ProblemPossible CauseSolution
Gauge does not power onNo 12V power, poor ground, faulty wiringCheck red wire for 12V, black wire for ground, and all connections.
Incorrect or no readingSensor not connected, faulty sensor, hose leak, incorrect hose routingCheck green wire connection to sensor, inspect hose for leaks/kinks, ensure sensor is properly installed.
Needle moves in jerks, not smoothlyLoose connections, sensor issue, air in lineEnsure all electrical and hose connections are tight. Check sensor for proper function.
Gauge reboots or flickersLoose internal contacts, poor power connectionCheck power and ground connections. If issue persists, contact support.
Alarm not activatingPressure not reaching threshold, faulty alarm circuitVerify boost pressure with another gauge if possible. Contact support if alarm circuit is suspected.

Specifications

FeatureSpecification
Gauge Size2 inch (52mm diameter)
Display Range-1~2 Bar / -30~30 PSI
Alarm Range-1.3~2 Bar / 20~30 PSI
Power SupplyProfessional 12V
Sensor Thread1/8NPT
Backlight Colors7-color selectable
MaterialPlastic
Item Weight0.25 kg
Item Dimensions (L x W x H)57mm x 52mm x 53mm
Boost gauge dimensions diagram

Image: Diagram showing the physical dimensions of the boost gauge.

User Tips

  • For enhanced durability and reliability, consider replacing the supplied PVC hose with a higher-quality silicone or nylon tubing, especially in high-temperature engine bay environments.
  • Ensure all electrical connections are crimped or soldered securely and insulated to prevent intermittent issues or reboots.
  • Regularly check the boost sensor and its connections for any signs of wear or damage to maintain accurate readings.

Warranty and Support

For any warranty claims, technical support, or inquiries regarding your boost gauge, please contact the seller directly through your purchase platform. Please have your order details available when contacting support.

A detailed user manual in PDF format is available for download here.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.