Introduction
This manual provides detailed instructions for the safe and effective use of your FREDORCH F7S or FR2 Sex Machine. Please read this manual thoroughly before operating the device to ensure proper setup, operation, and maintenance. This machine is designed for personal use and offers adjustable speed and angle settings for a customizable experience.
Safety Information
- Consult a Doctor: Do NOT use this product if you suffer from gynecological diseases, heart problems, or any physical or mental condition that renders you unable to withstand strong stimulation without first consulting with your doctor.
- Discomfort: Stop use immediately if you experience any discomfort.
- Lubrication: For best results, apply a personal lubricant (not included) as needed.
- Stable Surface: ONLY use this product on stable, level, and clean surfaces.
- Damage: Do NOT use this product if it is damaged or shows signs of malfunction. Repair or replace worn or broken parts before further use.
- Unattended Use: Do NOT leave this product unattended during use.
- Water Exposure: Do NOT get this product wet or operate it with wet hands.
- Power Disconnection: ALWAYS disconnect this product from its power source before cleaning, servicing, and storage.
- Material Compatibility: The machine is very powerful and does not support the use of glassware in order to prevent damage to the human body.
- Overcurrent Protection: The machine has three overcurrent protection. If the machine stops running, it only needs to unplug the power supply for 30 seconds and plug it in again.
- Age Restriction: This machine is strictly forbidden for minors under the age of 18. Please use this product within the scope permitted by law.
Product Overview & Components
The FREDORCH Sex Machine consists of a main engine, T-bar frame support, tie rods, power supply, and a speed controller. Depending on the version, it may also include a wireless remote control.
- Main Engine: The core unit containing the motor and control mechanisms.
- T-Bar (Frame Support): Provides stability and allows for height and angle adjustments.
- Tie Rods with Quick Joint: Connects accessories to the main engine. FR2 models include one tie rod, while F7S models include two (one shorter 30cm, one longer 50cm).
- Power Supply Package: Includes the power adapter and cords suitable for your country's plug type.
- Speed Controller: Adjusts the thrusting speed.
- Wireless Remote (Optional, Dual Control versions): Allows for remote adjustment of speed and modes.
Specifications
| Feature | 120W F7S Model | 80W FR2 Model |
|---|---|---|
| Power | 120W | 80W turbo gear motor |
| Electrical Input | 100-240V, 1.5A 50-60Hz | 100-230V |
| Electrical Output | 24V DC 5A | 24V |
| Noise Level | Up to 30 dB | Up to 30 dB |
| Peak Torque | 300NCM | 2.6Nm |
| Stroke Length / Telescopic Distance | 3-15 cm | 3-9 cm |
| Speed | 0-300 times/min (0-5 r/s) | 0-300 times/min (infinitely variable) |
| Remote Mode | N/A (Wired or Wireless) | 20 frequency conversion functions |
| Material | Stainless steel + aluminum alloy | Stainless steel + aluminum alloy |
| Machine Size (approx.) | 85cm x 45cm x 35cm | Varies by configuration |
| Adjustable Angle | -45° to +90° | -45° to +90° |
| Product Weight (approx.) | 8kg | 3.9kg |
Note: There may be slight errors in manual measurements. Refer to the specific model for exact dimensions and features.
Setup
Follow these steps to assemble your FREDORCH Sex Machine:
-
Install the 2-Tube Bracket:
Insert the long pipe into the short pipe clamp and reinforce it by twisting the screw clockwise with the inner hexagonal wrench.
Figure 2: Assembling the T-Bar frame. -
Assemble Main Engine and Pipe Bracket:
Reversely loosen the quick pipe clamp wrench, insert the pipe bracket into the fast pipe clamp and pull the fast pipe clamp wrench to lock it. The small screw can adjust the tightness of the quick pipe clamp as needed.
Figure 3: Attaching the main engine to the frame. -
Install the Self-Locking Fast Joint on the Sucker Rod:
Joints and rods are threaded. Twist the joints clockwise into the rod threads. The butterfly screw is counterclockwise reinforced.
Figure 4: Self-locking quick-plug interface for stable attachment. -
Install the Sucker Rod on the Main Engine:
One end of the extension rod thread is inserted into the main engine through the main engine casing and connected with the sliding block in the main engine, and then screwed into the sliding block thread hole clockwise.
-
Install Power Supply and Speed Regulator:
Install the power plug and governor into the corresponding plug of the control box.
-
Installation of Self-Locking Joints and Appliances:
If you need to remove an appliance, pull the joint ring in the opposite direction.
Operation
Once assembled, follow these steps to operate your machine:
- Connect to Power: Connect your machine to a grounded electrical outlet. Do not use 3-to-2 prong adapters or ungrounded power strips.
- Select Thrusting Mode: Use the speed controller or wireless remote (if applicable) to select your desired thrusting mode (1-20 for FR2 models).
- Start Operation: Press the 'play' button, and your machine will begin running.
- Adjust Settings: To change the height, angle, or thrusting length, adjust the corresponding parts of your machine. The angle can be adjusted from -45° to +90° to fulfill various posture needs. Stroke distance can be adjusted from 1-15cm (F7S) or 3-9cm (FR2).
- Stop Operation: Once finished, stop the thrusting and then disconnect your machine from its power source.
Maintenance
Proper maintenance ensures the longevity and hygiene of your device:
- Disconnect Power: Always unplug your machine after each use and prior to any cleaning or other maintenance.
- Clean Exterior: Clean the exterior of your machine after each use.
- Rod Cleaning: For the screw from the machine, rinse with clean water or mild detergent, and air dry it in a well-ventilated place away from direct sunlight.
- Other Parts: For other exterior parts, wipe with a soft, damp cloth. Do not use harsh detergents, abrasive cleaners, or caustic chemicals.
- Drying: Allow all parts to dry completely before further use.
Troubleshooting
- Machine Not Turning On (Cable Version): Ensure the governor is properly installed to turn on the power. Without it, the machine may activate automatic jump protection.
- Machine Stops Running: The machine has three overcurrent protection mechanisms. If it stops, unplug the power supply for 30 seconds and then plug it back in to reset.
- Unusual Noise: The sound generated when the machine is operated at a high level reaches 30dB, which is like whispering to the ear. If you experience louder or unusual noises, check for loose parts or obstructions.
User Tips
- Check Package Contents: Always verify that all accessories listed in your purchased package are included upon arrival. The number of accessories is based on the picture you purchased.
- Discreet Packaging: The product is shipped in neutral packaging to ensure your privacy.
- Dual Play: The machine features a double rod socket, allowing two players to use it simultaneously.
Warranty & Support
For any questions, concerns, or technical support regarding your FREDORCH Sex Machine, please contact the seller or manufacturer directly. Keep your purchase receipt for warranty purposes.
A user manual in PDF format is available for download: User Manual (PDF)