1. Product Introduction
This product is specifically designed to receive calls between aircraft and towers. It is a DIY kit that requires assembly. The module features a high-performance design capable of receiving signals from various types of aircraft and towers within a maximum range of about 190Km in open areas, when paired with a suitable high-performance antenna (such as a VHF Yagi antenna).
The kit incorporates a bandpass filter, 3355 high amplifier, CD7358 high amplifier+mixing, and MC1350 medium amplifier scheme, enabling it to receive AM signals in the 118-136MHz frequency range. The PCB board features printed inductor routing, which simplifies the assembly process. For a comfortable listening experience, an Automatic Gain Control (AGC) circuit and a mute function are built-in to avoid prolonged noise.
The PCB board measures 92mm x 75mm and can be housed in an aluminum chassis of 97mm x 40mm x 100mm.
2. Product Features
- Designed for receiving communication between aircraft and towers, with potential range up to 190Km using high-performance antennas.
- Equipped with a bandpass filter, 3355 high amplifier, and CD7358 high amplifier+mixing scheme for optimal signal processing.
- Supports AM mode, covering the 118-136MHz aviation band frequency range.
- PCB with printed inductor routing simplifies the assembly process for DIY enthusiasts.
- Built-in AGC circuit and mute function ensure a more comfortable and noise-free listening experience.
3. Specifications
| Parameter | Value |
|---|---|
| Power Supply | DC 9-12V |
| Antenna Impedance | 50 ohms, unbalanced type |
| Typical Receiving Current | 30mA |
| Receiving Frequency | 118MHz-136MHz |
| Working Mode | AM |
| Intermediate Frequency (IF) | 10.7 MHz (ceramic filter frequency selection) |
| Sensitivity | ≤ 0.5 μV |
| PCB Board Size | 92mm x 75mm |
For visual reference of the PCB dimensions, please see the image below:

4. Package Contents
The package includes:
- 1X Aviation Band Receiver DIY Kit (unassembled components)
Note: This kit is not soldered and is shipped with scattered electronic components. The finished board pictures are for reference only. Assembly is required.


5. Setup and Assembly
This product is a DIY kit and requires soldering and assembly. Basic soldering skills and knowledge of electronic components are necessary.
5.1 Assembly Steps (General Guidance)
- Identify Components: Carefully identify all components provided in the kit against the component list (if available in the PDF manual) and the PCB layout.
- Prepare PCB: Ensure the PCB is clean and free of any debris.
- Solder Low-Profile Components First: Start by soldering smaller components like resistors, diodes, and ceramic capacitors. Pay attention to polarity for diodes.
- Solder IC Sockets (if provided): If IC sockets are included, solder them before the ICs themselves. This protects the ICs from heat during soldering.
- Solder Larger Components: Proceed with larger components such as electrolytic capacitors (observe polarity), transistors, and integrated circuits (ICs).
- Solder Connectors and Potentiometers: Solder the DC power jack, antenna connector (BNC type), audio output jack, and the three potentiometers (TUN, SQ, AF).
- Inspect Soldering: After assembly, carefully inspect all solder joints for bridges, cold joints, or missing connections.
Refer to the official PDF manual for detailed component placement and soldering instructions. A link to the PDF is provided in the 'Warranty and Support' section.



6. Operating Instructions
Once the module is correctly assembled and inspected, follow these steps for operation:
- Connect Power: Connect a DC 9-12V power supply to the module's power input jack.
- Connect Antenna: Attach a 50-ohm unbalanced antenna (e.g., a GP antenna) to the BNC antenna connector.
- Connect Audio Output: Connect headphones or an external speaker to the audio output jack.
- Power On: Apply power to the module.
- Tune Frequency: Use the 'TUN' (Tuning) potentiometer to scan and select the desired aviation band frequency (118-136MHz).
- Adjust Squelch: Use the 'SQ' (Squelch) potentiometer to set the squelch level. This function mutes the audio output when no signal is present, reducing background noise. Adjust it until the background noise disappears, but a strong signal can still be heard.
- Adjust Audio Volume: Use the 'AF' (Audio Frequency/Volume) potentiometer to set the desired listening volume.

6.1 Operational Video
7. Maintenance
- Keep Dry: Protect the module from moisture and liquids to prevent damage to electronic components.
- Clean Gently: Use a soft, dry cloth to clean the module. Avoid using harsh chemicals or abrasive materials.
- Handle with Care: As an electronic circuit, avoid dropping or subjecting the module to strong impacts.
- Power Off When Not in Use: Disconnect the power supply when the module is not in use for extended periods.
8. Troubleshooting
8.1 Common Issues and Solutions
- No Reception or Weak Signal:
- Antenna Check: Ensure a proper 50-ohm unbalanced antenna is connected. For best results, an external antenna like a 1/4 wavelength GP antenna (approx. 60cm) is recommended.
- Line of Sight: VHF signals propagate almost in a straight line. Ensure there are no large obstacles (e.g., high-rise buildings, mountains, large towers) between your receiving location and the airport, especially if the airport is more than 25Km away.
- Power Supply: Verify the power supply is within the DC 9-12V range and is providing stable power.
- Excessive Noise:
- Squelch Adjustment: Adjust the 'SQ' potentiometer to eliminate background noise when no signal is present.
- Interference: Move the receiver away from other electronic devices that might be causing interference.
- No Audio Output:
- Volume Level: Ensure the 'AF' potentiometer is turned up.
- Headphone/Speaker Connection: Check the connection of your headphones or external speaker.
- Assembly Issues (for DIY Kit):
- Soldering Errors: Re-inspect all solder joints for cold joints, shorts, or incorrect component placement.
- Component Polarity: Double-check the polarity of diodes, electrolytic capacitors, and ICs.
- Missing Components: Ensure all components are correctly installed.
8.2 Recommended Antenna Type
For novice enthusiasts, GP antennas are recommended due to their ease of manufacture. A GP antenna typically consists of several metal rods and an M-mount.

9. User Tips
- Antenna Placement: Always aim for an unobstructed line of sight to the target area (e.g., airport) for optimal reception, especially for distances over 25km.
- Soldering Practice: If you are new to DIY electronics, consider practicing soldering on scrap boards before assembling the kit to ensure clean and reliable connections.
- Component Verification: Before soldering, verify each component against the circuit diagram and PCB markings to prevent errors.
10. Warranty and Support
As a DIY kit, specific warranty terms may vary. Please refer to the seller's policy at the time of purchase for details regarding returns or defective components.
For detailed assembly instructions, circuit diagrams, or further technical support, please consult the official user manual PDF provided by the manufacturer:
You may also contact Diymore Electronic Kit Store directly for assistance.