Autel MaxiIM IM508S

Contents

Autel MaxiIM IM508S IMMO Key Programming Diagnostic Tools User Manual

Model: MaxiIM IM508S

1. Introduction

The Autel MaxiIM IM508S is a powerful, fast, and smart professional key fob programming and scan tool. It combines advanced immobilizer and key programming functions with comprehensive diagnostic capabilities for all vehicle systems. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your IM508S device.

Autel MaxiIM IM508S main unit, XP200 key programmer, and a car key, highlighting key features like IMMO & Key Programming, 40+ Services, Active Test, IMMO Anti-Theft, and 2 Years Free Update.

Figure 1: Autel MaxiIM IM508S with XP200 and key, showcasing its primary functions.

2. Important Safety Information

IMPORTANT: Before operating or maintaining this unit, please read these instructions carefully, paying extra attention to the safety warnings and precautions. Failure to use this product properly may cause damage and/or personal injury and will void the product warranty.

3. Product Overview

3.1. MaxiIM IM508S Components

Diagram of Autel MaxiIM IM508S tablet showing labeled ports and features.

Figure 2: MaxiIM IM508S Tablet Overview.

  1. 7.0" LCD Capacitive Touchscreen
  2. Ambient Light Sensor: Detects ambient brightness.
  3. Power LED: Indicates battery level & charging or system status.
  4. Vehicle Communication LED: Flashes green when the tablet is communicating/linking with the vehicle's system.
  5. Collapsible Stand: Extends from the back to allow hands-free viewing of the tablet.
  6. Heat Sink
  7. Built-in Battery
  8. Mini USB Port
  9. Micro SD Card Slot: Holds the micro SD card.
  10. DB15-Pin Port: Connects the main cable.
  11. USB Port
  12. Lock/Power Button: Turns the device on & off with long press, or locks the screen with short press.

3.2. XP200 Key Programmer Components

Diagram of Autel XP200 key programmer showing labeled slots and ports.

Figure 3: XP200 Key Programmer Overview.

  1. Vehicle Key Chip Slot: Holds the vehicle key chip.
  2. Vehicle Key Slot: Holds the vehicle key.
  3. Status LED Light: Indicates the current operating status.
  4. DB15-Pin Port: Connects EEPROM Adapter and EEPROM Clamp Integrated MC9S12 Cable.
  5. Mini USB Port: Provides data communication and power supply.

4. Setup and Initial Configuration

4.1. Getting Started

  1. Register Your Product: Scan the QR code below or visit pro.autel.com to create an Autel ID and register your IM508S with its serial number and password. This is crucial for software updates and warranty support.
  2. QR code for Autel registration website.

    Figure 4: QR Code for Autel Registration.

  3. Power On: Ensure your IM508S tool is sufficiently charged or connected to a power source. Press and hold the Lock/Power button (item 12 in Figure 2) to turn on the key programming tool.
  4. Connect Main Cable: Connect the female adapter of the main cable to the DB15-Pin Port (item 10 in Figure 2) on the key programming tool and tighten the captive screws.
  5. Connect to Vehicle: Connect the 16-pin male adapter of the main cable to the vehicle's Data Link Connector (DLC), which is generally located under the vehicle dashboard. Your key programming tool is now ready for use.
  6. Diagram showing the IM508S connected to a vehicle's OBD-II port.

    Figure 5: Connecting the IM508S to the Vehicle's DLC.

4.2. Software Update

To ensure optimal performance and access to the latest vehicle coverage and functions, regularly update your IM508S software.

  1. Ensure the key programming tool is connected to the Internet via Wi-Fi.
  2. From the Home screen, tap the Update icon to view all available updates.
  3. Follow the on-screen instructions to download and install updates.
Screenshot of the IM508S home screen with the 'Update' icon highlighted.

Figure 6: Software Update Screen.

5. Operating Instructions

5.1. Immobilizer Function

The immobilizer function requires a connection among the vehicle, the IM508S key programming tool, and the XP200.

  1. Connect the vehicle and the IM508S key programming tool with the supplied main cable (as described in Setup).
  2. Connect the IM508S key programming tool and the XP200 with the supplied USB cable.
  3. Select IMMO on the Home screen and follow the on-screen instructions to continue.
Diagram showing the IM508S connected to the XP200 and the vehicle for immobilizer functions.

Figure 7: Immobilizer Function Connection Diagram.

5.2. Key Programming and Generation

The IM508S, especially when paired with the XP200, offers extensive key programming capabilities.

Image detailing IMMO Functions and Programming Functions, including key generation, EEPROM/MCU read/write, and support for various vehicle systems.

Figure 8: IMMO and Programming Functions Overview.

IMMO Functions include: Auto Detect Make/Model/Year/System, Read PIN/CS (All-Key-Lost), Key Generation, Key Learning, Remote Learning, IMMO ECU Reset/Adaptation, IMMO ECU Refresh/Coding, Backup/Restore IMMO Data, BDC Key Learning, ECU Adaptation, VAG IMMO III/IV/V Add Key, All-Key-Lost, Benz 3rd Gen IMMO Add-Key, Key-Learning, BMW CAS4/3/2 Key Learning, VAG MQB Add-Key, G5 2015+ Key Learning.

Programming Functions include: Key Read/Write, EEPROM Read/Write, MCU Read/Write, ECU Read/Write, MC9S12 Encryption Chip Read/Write, IC Card Read/Write, Mercedes Infrared Key Read/Write, Remote Frequency Detect, Support PC.

Key Generation Demonstration:

Video 1: Demonstration of Universal Key Generation using the Autel MaxiIM IM508S and XP200.

To generate a universal key:

  1. Ensure only one universal key is within 10 cm of the key slot of the device to avoid interference.
  2. Check that a battery is installed in the universal key, then place the universal key into the key slot of the XP200.
  3. Press Generate Universal Key to start generation.
  4. Keep the universal key stable in its place during generation.

5.3. Diagnostic Functions

The IM508S provides OE-level full systems diagnostics and a full bidirectional active test.

Image illustrating Full Bidirectional Active Test and OE-Level Full Systems Diagnostics, showing various tests like fuel injector, A/C clutch, wipers, ABS pump, mirror, and door tests.

Figure 9: Full Bidirectional Active Test and OE-Level Full Systems Diagnostics.

Diagnostic Capabilities:

  • Scan All Available Modules to Read/Erase DTCs (Diagnostic Trouble Codes).
  • Display Live Data (Graph/Text Data).
  • AutoVIN/AutoScan for quick vehicle identification.
  • ECU Information retrieval.

Bidirectional Active Test: The tool controls vehicle actuators' movement by sending commands to its ECU. This is widely used on vehicles to help quickly check if car actuators for windows, rear mirrors, sunroof, wipers, etc., are in good condition or to perform active tests for specific purposes.

5.4. Enhanced Maintenance Services

The IM508S offers over 28 enhanced maintenance services.

Image showing 28+ Enhanced Maintenance Services icons, including IMMO Reset, BMS Reset, Inject Reset, Headlamp, Airbag Reset, Brake Bleed, EPB, and more.

Figure 10: Enhanced Maintenance Services.

These services include, but are not limited to: IMMO Reset, BMS Reset, Inject Reset, Headlamp, Airbag Reset, Brake Bleed, EPB, Cylinder, Limit, SAS, TEC Learn, FRM RESET, ACC, CHG, A/C, VIN, Seats, Throttle, Car Mirror, WinAndDoor, VGT learn, CCS/ACC, Speed & PTO, LangChange, Rain/Light Sensor.

5.5. Smart Mode vs. Expert Mode

The IM508S provides two operational modes to cater to different user skill levels:

Image comparing Smart Mode for primary technicians with guided functions and Expert Mode for skilled technicians with individual IMMO key programming.

Figure 11: Smart Mode and Expert Mode.

  • Smart Mode: Accesses a function menu where each function is configured as a smart guide system. Ideal for primary technicians, providing guided functions with step-by-step instructions.
  • Expert Mode: Accesses a function menu where each function is configured as a smart guide system. Designed for skilled technicians, offering a convenient way to perform individual IMMO key programming functions they need.

6. Maintenance

6.1. Software Updates

Regularly check for and install software updates to ensure your device has the latest vehicle coverage, bug fixes, and new features. Connect your device to Wi-Fi and navigate to the 'Update' section on the home screen.

6.2. Battery Care

The device is powered by a 3.7 V/5000 mAh lithium-polymer battery. To prolong battery life:

  • Avoid fully discharging the battery frequently.
  • Store the device in a cool, dry place when not in use for extended periods.
  • Charge the device using the provided 5 VDC power supply.

6.3. Cleaning

Use a soft, damp cloth to clean the device. Avoid using abrasive cleaners or solvents that could damage the screen or casing.

7. Troubleshooting

7.1. LED Indicators

Understanding the LED indicators can help diagnose basic issues:

LEDColorDescription
Power LED (IM508S)GreenFlashes green when charging.
RedFlashes red when an error has occurred.
Status LED (XP200)RedLights red when the firmware is upgrading or an error has occurred. Lights red briefly when the device is powered on and performing self-check.
GreenFlashes green when communicating via USB cable. Lights green when the device is ready for use.

7.2. Common Issues for Universal Key Generation

If you encounter issues during universal key generation, consider the following:

  • Dead Battery: Ensure the universal key has a working battery installed.
  • Incorrectly Placed Universal Key: Make sure the universal key is correctly seated in the XP200's key slot.
  • Environmental Interference: Minimize electromagnetic interference from other electronic devices during the generation process.

8. Specifications

AttributeValue
Model NameAutel MaxiIM IM508S
Item TypeAuto Key Programmer
Brand NameAutel
Operating SystemAndroid 11
ProcessorRockchip RK3566 Quad core, 4x 1.8GHz (A55)
Memory4GB RAM & 64GB On-board Memory
Display7-inch LCD capacitive touchscreen with 1024x600 resolution
ConnectivityMini USB 2.0, USB 2.0, Wi-Fi, Micro SD card (supports up to 32GB)
SensorsAmbient light sensor for brightness auto changing
Audio Input/OutputInput: N/A, Output: buzzer
Power and Battery3.7 V/5000 mAh lithium-polymer battery, Charges via 5 VDC power supply
Tested Battery LifeAround 4.5 hours of continuous use
Operating Temperature0 to 50°C
Storage Temperature-20 to 60°C
Operating Humidity5% - 95% non-condensing
Dimensions (W x H x D)300 mm x 220 mm x 50 mm
Item Weight5.1 kg
Supported SystemsABS, DPF, EPB, SAS, SRS, TPMS, Engine, Transmission, BMS, Oil Reset, BMS, Seats, Injector, Suspension, Throttle, IMMO Keys, WIN DR POOF, Brake bleed, IMMO Key Programming, advanced key learning, IMMO ECU reset/adaptation, refresh/coding, key generation, EEPROM/MCU read/write
ProtocolsISO9141-2, ISO14230-2, ISO15765, Highspeed, Middlespeed, Lowspeed and Singlewire CAN, SAE-J1850 PWM, CAN ISO 11898, fault-tolerant CAN SAE J2610, GM UART, UART Echo Byte Protocol, Honda Diag-H Protocol, TP2.0, TP1.6
FeaturesBacklit Display, Built-In Battery, Check Engine Light Shut Off, Erases Codes, Freeze Frame Displays, Internet Updateable, LCD Display, Multi-Language Interface, User Friendly, Color Display
Multi-Language SupportEnglish, Spanish, Russian, Portuguese, Italian, Polish, Japanese, Korean, German, Swedish, Turkish, Vietnamese, Arabic, Thai
Software UpdateYes (2 Years Free Update)
Warranty1 Year

9. User Tips

  • Verify Update Period: While the product generally includes 2 years of free updates, some users have reported receiving devices with 1 year initially. If this occurs, contact the seller or Autel support to ensure your 2-year update period is activated.
  • Performance: The IM508S is noted for its powerful capabilities and ease of use, often compared favorably to other professional scanners.
  • Customer Service: Many users highlight responsive sellers and good customer service for activation and support.

10. Warranty and Support

10.1. Warranty

The Autel MaxiIM IM508S comes with a 1-year warranty. Please refer to the full warranty terms and conditions available on the official Autel website or in the comprehensive user manual.

10.2. Technical Support

For technical assistance, software updates, or any product-related inquiries, please contact Autel support:

10.3. Additional Documentation

A comprehensive user manual in PDF format is available for detailed instructions and advanced operations. You can view or download it from the following link:

View User Manual (PDF)


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.