1. Product Overview
The LED Daytime Running Light (DRL) is a core safety lighting component designed to improve vehicle visibility during daytime driving and reduce traffic accidents. It is suitable for most passenger cars, SUVs, and light commercial vehicles.
These DRLs are designed to automatically turn on when the vehicle starts (without activating the main headlights) and turn off when the main headlights are activated.
Composition:
- LED lamp beads
- Lamp housing
- Wiring harness
- Control module
- Mounting bracket
- Fixing screws
The lamp housing is waterproof and dustproof, and the LED beads utilize high-brightness, energy-saving chips.
Features:
- High brightness
- Low power consumption
- Long service life
- Waterproof (IP67/IP68)
- Dustproof
- Corrosion-resistant
- Quick startup
- Consistent with automotive electrical system specifications
- Does not affect the vehicle's original electrical circuit
- Easy to install
Quality:
100% brand new and factory-tested (brightness, waterproof, voltage resistance test). Guaranteed no lamp bead damage, wiring defects, or control module failure. Suitable for direct installation and replacement.
2. Safety Information
WARNING:
- Turn off the engine, vehicle power, and disconnect the negative battery terminal before installation to avoid short circuit, electric shock, or damage to electrical components.
- Wear protective gloves and goggles when drilling and installing to prevent scratches, debris splashing, and injury.
- Do not operate while the vehicle is moving or the engine is running to avoid safety hazards and installation errors.
- Keep small parts (screws, cable ties) and the lamp away from children to prevent accidental ingestion or injury; do not touch the lamp beads when the light is on (high temperature may cause burns).
- If lacking professional electrical and installation experience, entrust the operation to a qualified auto repair technician.
- Do not use damaged, deformed, or mismatched daytime running lights, as this may cause short circuit, lamp burnout, or traffic safety hazards.
3. Installation Instructions
3.1 Pre-installation Preparation
- Park the vehicle stably on a flat surface, turn off the engine, and turn off the vehicle power.
- Disconnect the negative battery terminal to avoid short circuit.
- Prepare necessary tools: screwdrivers, wrench, drill (if needed), insulating tape, and cleaning cloth.
- Inspect the new daytime running light (with matching accessories) for housing damage, lamp bead burnout, or wiring looseness.
- Clean the mounting position (front bumper or fender) to remove dust and oil stains.
3.2 Installation Steps
- Determine the mounting position (follow the vehicle's original design or the product guide). If no original mounting holes, mark the drilling position and drill holes (pay attention to avoid damaging the vehicle body and internal wires).
- Fix the daytime running light bracket to the vehicle body with screws, ensuring it is firm and does not shake. Adjust the lamp angle to ensure uniform light emission.
- Route the wiring harness along the vehicle body, avoiding sharp edges and high-temperature areas. Fix it with cable ties and connect the harness connector to the control module.
- Connect the control module's power cord to the vehicle's positive and negative battery terminals (or the corresponding fuse position). Ensure correct polarity. Wrap the connection with insulating tape for waterproof and dustproof protection.
- Reconnect the negative battery terminal. Start the vehicle and check if the daytime running light turns on automatically. Turn on the main headlights and confirm the daytime running light turns off normally.
- Check the entire installation for loose wires, unstable mounting, or light deviation, and adjust accordingly.
3.3 Installation Notes
- Always disconnect the negative battery terminal before installation to avoid short circuit.
- Do not drill randomly to prevent damaging the vehicle body or internal circuits.
- Ensure the lamp is mounted firmly to avoid falling off during driving.
- Route the harness neatly and avoid extrusion or wear.
- Confirm correct polarity connection to prevent lamp damage.
- Do not modify the lamp's internal structure or wiring.
4. Operating Instructions
Once properly installed, the LED Daytime Running Lights are designed for automatic operation:
- The DRLs will automatically turn on when the vehicle's engine is started.
- The DRLs will automatically turn off when the vehicle's main headlights are activated.
This automatic functionality ensures enhanced visibility during daylight hours without requiring manual intervention.
5. Maintenance & Inspection Tips
To ensure optimal performance and longevity of your daytime running lights, perform checks every 3 months:
- Lamp Housing: Inspect for cracks, water intrusion, or other damage.
- Lamp Beads: Check for burnout or dim light.
- Wiring Harness: Examine for looseness, wear, or corrosion.
- Cleaning: Regularly clean the lamp surface to remove dust and dirt. Always turn off the light and allow it to cool down first before cleaning.
- Replacement: If the lamp or wiring harness fails to turn on or works abnormally, replace it immediately.
- Storage: Store unused lamps in a dry, cool environment away from high temperature, humidity, and direct sunlight.
6. Fault Troubleshooting
| Fault Symptom | Possible Causes | Troubleshooting |
|---|---|---|
| Daytime running light does not turn on | Incorrect polarity connection, loose wiring, lamp bead burnout, control module failure | Check polarity and wiring, replace lamp beads or control module if needed |
| Light is dim or flickering | Poor contact, voltage instability, lamp bead aging | Reconnect wiring, check vehicle power supply, replace aging lamp beads |
| Water intrusion into lamp housing | Lamp housing damaged, waterproof seal failure, improper installation | Dry the lamp, replace the lamp housing or seal, re-install to ensure waterproof |
7. Product Specifications
- Material: ABS Plastic + LED
- Condition: 100% Brand New
- Item Type: Day Light / LED Daytime Running Light
- Fitment Type: Direct Replacement
- Quantity: 2 pcs (1 Pair)
- Manufacturer Part Number: A1649060351, A1649060451
- Model Name: C115-277-Kit
- Placement on Vehicle: Left, Right, Front
- Lens Color: Clear
- Origin: Mainland China
- Fitment For: Mercedes-Benz X164 GL320 GL350 GL450 ML63 AMG X166 (2007-2013 models, ONLY Fit for 7 LED versions)
8. Warranty & Support
We provide a 12-month warranty covering material and manufacturing defects. The warranty does not cover damage resulting from:
- Improper installation
- Incorrect polarity connection
- Lamp burnout due to overvoltage
- Physical damage (e.g., collision, scratch)
To apply for after-sales service, please provide purchase vouchers and photos of the defect. This product is intended for vehicle daytime lighting only and is not for vehicle electrical system modification.
For additional guidance, you may refer to the official user manual PDF: View User Manual (PDF)
9. User Tips
No specific user tips or common questions were provided for this product. Always follow the installation and safety guidelines carefully.