1. Introduction
This manual provides instructions for the 3.7V Fan Motor Speed Controller Board, a compact and versatile circuit designed for small handheld fans. It features a built-in boost circuit to convert lower battery voltages (e.g., 3.7V lithium) to higher output voltages (5V, 7V, or 9V) to meet various fan motor requirements. The board also boasts a low standby current to maximize battery life.
Product overview video demonstrating the 3.7V Fan Motor Speed Controller Board.
2. Key Features
- Compact Design: Miniaturized for installation in devices with limited space.
- Boost Conversion Function: Converts 3.7V lithium battery voltage to 5V, 7V, or 9V outputs.
- Low Standby Current: Consumes extremely low current (approx. 10uA) in standby mode to extend battery life.
- Multi-Voltage Output Support: Adaptable for fans with different power requirements.
- Wide Range of Use: Ideal for small handheld fans powered by lithium batteries.
- Type-C Charging Port: Convenient charging via Type-C 5V input.
- Reverse Protection: Integrated reverse protection for both battery and fan connections.
3. Setup and Connections
Carefully follow the instructions below for proper connection of the fan motor speed controller board.
3.1. Board Layout and Port Description
Diagram of the control board with port descriptions: Type-C charging port, Switch/shift button, Fan connection, Battery connection, Charging indicator, Gear indicator.
Key ports and indicators:
- Type-C Charging Port (J3): For 5V power input.
- Switch/Shift Button (K2): Used to cycle through fan speeds and turn off the device.
- Fan Connection (F+/F-): Connects to the fan motor.
- Battery Connection (B+/B-): Connects to the 3.7V lithium battery.
- Charging Indicator (LED4, LED5): Indicates charging status.
- Gear Indicators (LED1, LED2, LED3): Indicate the current fan speed/voltage output.
3.2. Battery Connection
The board is designed for a 3.7V lithium battery (e.g., 18650 type) with a PH2.0 female socket. Ensure correct polarity when connecting the battery. The board includes reverse protection for the battery end.
Control board showing battery input range (3-4V) and battery polarity (Positive/Negative).
If using the provided PH2.0 wiring to connect to the fan end, you may need to switch the red and black wire directions yourself to match the fan's polarity.
3.3. Fan Motor Connection
Connect your 5-8 inch brushless fan motor to the PH2.0 female base at the fan end (F+/F-). The board supports a third speed output of 9V 600mA. The fan end also features reverse protection.
Control board showing input (5V 1A), connection points for 3.7V battery and motor, and work light indicator.
3.4. Charging
Connect a Type-C 5V power source to the Type-C charging port (J3) for charging the 3.7V lithium battery. The board supports simultaneous charging and discharging. If the board is not equipped with a battery, it can only operate in the lowest gear when powered via Type-C. For full functionality without a battery, ensure a 5V2A power supply is connected to the fan power supply end.
Detailed wiring diagram for 9V fan three-stage charging and discharging control board, including TYPE-C port, LED indicators for 5V, 7V, 9V, switch, and battery/fan connections.
4. Operating Instructions
The control board offers three fan speed gears and a shutdown cycle, indicated by different colored LEDs.
- Power On: Press the Switch/Shift button (K2) to turn on the fan.
- Gear 1 (5V Output): The red LED (LED1) will illuminate.
- Gear 2 (7V Output): Press the Switch/Shift button again. The green LED (LED2) will illuminate.
- Gear 3 (9V Output): Press the Switch/Shift button a third time. The blue LED (LED3) will illuminate.
- Shutdown: Press the Switch/Shift button a fourth time to enter the shutdown cycle.
The boost conversion function ensures that the fan motor receives the appropriate voltage (5V, 7V, or 9V) from the 3.7V battery to achieve desired speeds.
Image illustrating the boost conversion function of the control board, showing the board and included wiring.
Image highlighting the multi-voltage output support of the control board.
5. Maintenance
The control board is designed for durability and low power consumption. No specific routine maintenance is required. To ensure optimal performance and longevity:
- Keep the board clean and free from dust and moisture.
- Avoid exposing the board to extreme temperatures or direct sunlight.
- Handle with care to prevent physical damage to components or connections.
Image demonstrating the low standby current feature of the control board, which contributes to extended battery life.
6. Troubleshooting
- Fan only operates in lowest gear: If the board is not equipped with a battery, it will only operate in the lowest gear when powered via Type-C. For full functionality without a battery, ensure a 5V2A power supply is connected directly to the fan power supply end.
- Fan not working after wiring: Double-check the polarity of the fan motor connection. If using the provided PH2.0 wiring for the fan end, you might need to switch the red and black wire directions to match your fan's polarity. The fan end has reverse protection, but incorrect wiring can prevent operation.
- Device not charging: Ensure the Type-C power source is providing 5V. Check the charging indicator LEDs.
7. Specifications
| Parameter | Value |
|---|---|
| Product Name | Boost Board 9V Charging Fan Control Board |
| Model | ZR-F17-V2-20220428 |
| Brand | diymore |
| Input Voltage | Type-C 5V |
| Battery Input Voltage | 3-4V (for 3.7V Lithium Battery) |
| Output Voltage (Gears) | Gear 1: 5V, Gear 2: 7V, Gear 3: 9V |
| Max Output Current | 0.6A (for fan terminal) |
| Third Speed Output (Fan) | 9V 600mA |
| Standby Current | ~10uA |
| Battery Connector | PH2.0 female socket (for 4.2V ternary/polymer lithium battery like 18650) |
| Fan Connector | PH2.0 female base (for 5-8 inch brushless motors) |
| Charging Power | 5W |
| Product Size | 35.6mm x 27mm |
| Circuit Board Thickness | 1.5mm |
| Highest Terminal Height | 8mm |
| Operating Temperature | -10°C to +65°C |
| Package | DIP |
| Origin | Mainland China |
Image showcasing the compact design of the control board and included wiring.
8. User Tips
- Check Dimensions: Before purchasing or installing, verify the product dimensions (35.6mm x 27mm) to ensure it fits your intended device, especially if space is limited.
- Wiring Polarity: Always double-check the polarity of your battery and fan connections. While the board has reverse protection, ensuring correct wiring from the start prevents potential issues.
- Power Supply for Battery-less Operation: If you plan to use the board without a connected battery, ensure you provide a stable 5V2A power supply directly to the fan power input for full functionality across all gears. Otherwise, it may only operate in the lowest gear.
9. Warranty and Support
For any technical assistance, warranty claims, or further inquiries, please contact the seller directly through the platform where the product was purchased. Please refer to the official user manual PDF for additional details and diagrams: User manual (PDF).