Introduction
Before using your new Smart Door Lock, please carefully review the following precautions to ensure proper installation, configuration, and safe operation.
Packing List
Please check the package contents against the list below:
- Exterior Assembly x 1
- Interior Assembly x 1
- Latch Bolt x 1
- Lock Fixing Column x 1
- Fixing Column x 2
- Fixing Post x 2
- Latch Screws x 4
- Strike Plate x 1
- Plastic Box x 1
- Spring x 1
- Backup Keys x 2
- User Manual x 1
Installation Guide
Watch the installation video for a visual guide:
Video Description: A step-by-step guide demonstrating the physical installation of the smart door knob, including preparing the door, assembling components, and connecting wiring.
Door Preparation and Dimensions
Ensure your door meets the following specifications:
- Door Thickness: 1-3/16" - 2" (30mm-50mm)
- Hole Diameter: 1-1/2" (38mm) or 2-1/8" (54mm)
- Backset: 2-3/8" or 2-3/4" (60mm or 70mm)
- Door Compatibility: Requires a chiseled latch hole and is compatible with Rim Cylinder type doors. Not compatible with Mortise/Integrated locks or non-chiseled latch holes.
Step-by-Step Installation
- Install Latch Body: Install the latch on the door first. Secure it with screws.
- Prepare Front Panel: Install the two screw bolts on the front cover. Insert the hollow square bar into the bottom of the front handle, ensuring the data line sticks out. Use pliers to secure the copper columns on the front panel.
- Prepare Rear Panel: Remove the battery baffle plate from the interior assembly and install the screws.
- Route Cables and Install Exterior: Route the data cable through the square bar. Insert the exterior assembly into the door hole.
- Connect Rear Panel: Connect the rear panel to the data cables. Tighten the door lock with two screws. Note: Connect the terminals according to the red markings to prevent failure.
- Install Batteries and Baffles: Install 4 AAA alkaline batteries into the corresponding slots, observing positive and negative terminals. Place the battery cover based on the limit slot.
- Install Battery Cover Retaining Ring: Ensure the small round hole on the retaining ring is in the upper left corner and in the same direction as the rear circuit board.
- Secure Battery Cover: Press firmly down on the battery cover, then rotate the retaining ring in a clockwise direction to secure it. To open, press firmly and turn counter-clockwise.
App Configuration & Operation
The Viladepot Smart Door Knob D2 offers multiple ways to unlock and manage access.
Download and Pair the App
The smart lock uses the Tuya Smart app. Download and install it from your app store.
- Open the Tuya Smart app, click the "+" icon, and then click "Add Device" to prepare for pairing.
- On the smart lock, press 1 + 1 + SMART + Your admin-password. (DEFAULT PASSWORD IS 123456)
- After approximately 10 seconds, the device should automatically appear in the app for pairing. Click on it to pair.
Note: If the device has already been added to another phone, it will not enter pairing mode but will go into standby mode.
Adding Fingerprints and Passwords
To add new access methods:
- In the Tuya Smart app, click "Member Management".
- Select "Fingerprint" or "Code" (password) to set up new entries.
- Follow the in-app guide to complete the setup process. For fingerprints, you will be prompted to place your finger on the sensor multiple times at different angles.
The smart lock boasts a 99% recognition rate, supports up to 30 fingerprints, and has a 0.1s recognition speed.
Muting "Beep Beep" Sounds
To mute the sound notifications:
- In the Tuya Smart app, navigate to "more".
- Press "Mute Settings", and then press "open" to toggle the mute function.
Unlocking Methods
The smart door knob supports four unlocking methods:
- Fingerprint Unlock: Use registered fingerprints on the sensor.
- Password Unlock: Enter a registered passcode on the keypad.
- APP Unlock: Use the Tuya Smart app on your smartphone via Bluetooth.
- Mechanical Key Unlock: Use the provided backup keys for traditional unlocking.
Maintenance
Battery Replacement
The smart lock requires four #7 (AAA) dry batteries. We recommend replacing the batteries after 180 days. Keep an eye on the battery level weekly via the Tuya app. If the battery level falls below 30%, replace the batteries promptly to ensure continuous operation.
Troubleshooting
- Fingerprint Recognition Not Working: If the smart lock has power, try again by changing the angle of your finger. If it has no power, use a spare key to unlock the door and replace the batteries. If these methods do not resolve the issue, please contact support.
- Device Not Connecting to App: Ensure the lock is in pairing mode (follow app configuration steps). If it was previously paired with another phone, it might be in standby mode.
- General Issues: If you encounter any problems with installation, setup, or future use, please contact our support team.
Specifications
| Attribute | Specification |
|---|---|
| Brand Name | Viladepot |
| Model Number | D2 |
| Power Supply | DRY BATTERY (4x AAA batteries) |
| Handle Direction | Direction Reversible |
| Suitable for Mortise | 6068 |
| Protection Level | No Waterproof |
| Fit Door Thickness | 30-50mm |
| Suitable Door Type | Wooden Door, Brass Door, Stainless Steel Door, Steel Door, Other (Inner doors) |
| Finish Type | Painted |
| Doorknob Function | Biometric, Key & Keypad |
| Connectivity | Bluetooth |
| Ways To Unlock | Mechanical Keys, Password, Fingerprint, Bluetooth, App, Other |
| Smart Home Platform | Tuya |
| Certification | FCC |
| Silent Mode | Yes |
Note: This product is not waterproof and is primarily intended for inner doors.
User Tips
- While initial instructions might seem confusing, setting up codes and fingerprints is straightforward once you get the hang of it.
- The fingerprint entry is highly responsive and works immediately.
- The lock connects via Bluetooth to the Tuya app, not Wi-Fi. This means you need to be within Bluetooth range for app-based unlocking and management.
Warranty & Support
Warranty
We provide a 30-day worry-free money-back guarantee and a one-year limited warranty. For any problems, please feel free to contact us.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warnings
Please keep an eye on the remaining battery power of the product regularly. We highly recommend that you replace the battery when the product falls below 30% power.
Contact Support
If you have problems with installation, setup, or future use, please contact us. We are here to help you reliably!
E-mail us at: support@viladepot.com
For a detailed user manual, you can refer to the official PDF document: User manual (PDF)