1. Introduction
Thank you for purchasing the Baofeng 5R Mini Ham Radio. This dual-band, dual-display, and dual-watch radio is designed to provide secure, instant, and reliable communications. Please read this manual carefully before use to ensure maximum performance and safe operation of your radio.
General Safety Warnings
WARNING! European Users:
Operation of this unit in Transmit mode requires a valid Amateur Radio License from your respective Country's Amateur Radio Licensing Authority for the Frequencies and Transmitter Power levels this Radio transmits on. Failure to comply may be unlawful and liable for prosecution. Refer to the "EU" specification guide 2014/53/EU.
ATTENTION! Programming the Radio:
When programming the radio, always start by reading the factory software data. Then, rewrite this data with your desired frequency settings into a new saved code plug to avoid errors. A programming cable and PC can be used to set authorized frequencies, bandwidth, power, etc. Ensure your programming complies with your FCC (or EU/other country) license certification.
ATTENTION! RF Energy Exposure:
Before using this product, read the RF Energy Exposure and Product Safety Guide that ships with the radio. This guide contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations.
PMR446, FRS, GMRS, MURS Frequencies
While you may be tempted to use PMR446 (in Europe) or FRS, GMRS, MURS (in the USA) frequencies, please note that there are restrictions on these bands that make this transceiver illegal for use on them.
2. Package Contents
The following items are typically included in the package. Please check to ensure all components are present.
| Item | Quantity (PCS) | Item | Quantity (PCS) |
|---|---|---|---|
| Radio | 1 | Lanyard | 1 |
| Battery | 1 | Operation Manual | 1 |
| Antenna | 1 | Belt Clip | 1 |
*Charger and power adapter are subject to the final configuration of the dealer. The charging instructions in this manual may not be appropriate if a Type-C charging method is used.
3. Product Overview
The Baofeng 5R Mini features a 1.44" TFT large screen, full keyboard, and supports dual watch, dual PTT, and Bluetooth programming.
Radio Components
Refer to the diagram below for the location of key components:
- Antenna
- SK1-Customized Function Keys/Monitor button
- PTT-A Button
- OK/Menu button
- V/M-VFO/MR
- PTT-B Button
- Numeric Keypad
- Flashlight
- Volume/Power Knob
- Screen
- Accessory Port
- Cancel/Back button
- ▲ Up button/▼ Down button
- A/B
- Microphone
- LED Indicator
- Battery Latch
- Type-C Charging indicator light
- Type-C Charging Port
- Search/Flashlight button
LCD Display Icons
The LCD screen displays various icons to indicate the radio's status and active functions:
| Icon | Description |
|---|---|
| RSSI | Squelch Open/Close Indicator |
| H/L | Transmit power level indicator (High/Low) |
| ♪ | DTMF side tone from radio speaker (DT-ST, ANI-ST, DT+ANI) |
| D | DCS enabled |
| C | CTCSS enabled |
| + | Repeater access in VFO/Frequency Mode (TX shifted higher than RX) |
| - | Repeater access in VFO/Frequency Mode (TX shifted lower than RX) |
| D | Dual watch enabled |
| 6 | Keypad lock enabled |
| V | VOX enabled |
| J | Confidential calling feature activated |
| N | Narrowband enabled |
| _ | Battery level indicator |
| R | Reverse function enabled |
| T | Terminal switched from transit mode to pass-through mode |
| SCR | Voice scramble function activated |
4. Setup
Attaching the Antenna
Turn the antenna clockwise until it is tight. To remove the antenna, turn it counterclockwise.
CAUTION:
- Do not hold the radio antenna in your hand during operation, as this will reduce the performance of the radio and shorten the antenna's life.
- Do not shake the radio with the top of the antenna in your hand, as this will degrade performance and life.
- Do not use the radio with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Contact your local dealer for a replacement antenna.
Battery Charging
When using the terminal for the first time, a low battery warning may occur. It is recommended to turn off the radio during charging.
Charging Prohibitions
- Do not charge or replace your battery in locations containing fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
- Do not charge a wet battery. Dry it with a soft, clean cloth prior to charging.
- Do not charge a battery that is deformed, leaking, or overheating.
- Do not charge your battery with an unauthorized charger.
- Do not charge your battery in a location where strong radiation is present.
- Overcharging is prohibited as it may shorten battery life.
Battery Maintenance Instructions
- Accumulated dust on the charging connector may affect normal charging. Wipe it with a clean, dry cloth regularly.
- It is recommended to charge the battery between 5°C and 40°C. Charging outside this range may reduce battery life or cause leakage.
- To charge a battery attached to the product, turn it off to ensure a full charge.
- Do not remove the battery or unplug the power cord during charging to ensure a smooth charging process.
Battery Indicator Light
| Indicator Light | Charging Status |
|---|---|
| Red light is always on | Charging |
| Green light is always on | Charging complete |
5. Operating Instructions
Turning Your Radio On and Off
- To turn your radio ON, turn the [Volume/Power] rotary knob clockwise.
- To turn your radio OFF, turn the [Volume/Power] rotary knob counterclockwise.
Setting the Volume
- Increase volume by turning the [Volume/Power] rotary knob clockwise.
- To decrease volume, turn the [Volume/Power] rotary knob counterclockwise.
- Do not hold the radio close to your ear if the volume is set to an uncomfortable level, as it could cause hearing damage.
Locking or Unlocking Keypad
To prevent accidental changes to radio settings:
- Press and hold the [*] key to lock the keypad until the "6" icon is displayed on the screen.
- In lock mode, you can still turn the intercom on/off, adjust volume, receive, transmit, send call tones, send emergency alerts, and listen to channels. All other functions remain locked.
- To unlock, press and hold the [*] key again until the "6" icon is no longer displayed.
Keypad Entry
The numeric keypad allows you to enter radio aliases, channel aliases, numbers, and other characters.
- To switch between input methods, press the [#] key.
- Press '1' to enter a special character (except in numeric input mode).
- Press '0' to enter a space (except in numeric input mode).
Select a Channel
- Press the [V/M] button to toggle between VFO (Frequency) and Channel mode. Select Channel mode.
- Press the ▲/▼ buttons or rotate the encoder to select the desired channel.
- Alternatively, enter the 3-digit channel number directly using the keypad (e.g., '064' for channel 64).
Channel Memory
In Frequency and Standby mode, you can store frequencies and parameters:
- Press [MENU] [3] [MENU] [1] [5]. The screen will display "MEMCH".
- Press [MENU] to enter the function.
- Press the ▲/▼ buttons to select the channel, then press [MENU] to store it. A sound tone will confirm success.
- Press [EXIT] to return to standby mode.
Note: If you want to set CTCSS tones, DCS codes, or frequency offset, do so before storing the channel. Stored channels are displayed as CH-.
Delete a Channel (DEL-CH)
In VFO mode and Standby mode:
- Press [MENU] [3] [MENU] [1] [6]. The screen will display "DELCH".
- Press [MENU] to enter the function.
- Press the ▲/▼ buttons or rotate the encoder to select the channel to delete.
- Press [MENU] to confirm.
- Press [EXIT] to return to standby mode.
Note: Channel 1 cannot be deleted.
Main Band/Sub Band Switch
In standby mode, press the [A/B] key to toggle between the A and B bands. The highlighted band is the main band, and the darker displayed band is the sub-band.
VFO/Channel Switch
Press the [V/M] button to switch between VFO (Frequency) and Channel display. VFO mode displays the 'VFO' icon, while MR (Memory Recall) mode displays the channel serial number.
Setting the VFO Frequency
Turn the radio to VFO mode, then press the [A/B] key to switch to the main channel.
- Operation 1: Input the VFO frequency directly with the keypad.
- Operation 2: Press the ▲/▼ button or rotate the encoder to adjust the VFO frequency in the set frequency step.
Call Service (Transmitting and Receiving)
All radios in a group must be set to the same channel and sub-code to communicate. For optimal reception volume, keep the microphone 2.5 cm to 5 cm from your mouth when transmitting.
- Initiate a call: Select a channel. Press and hold the [PTT-A] key to transmit on segment A (upper screen), or [PTT-B] key to transmit on segment B (lower screen). The red indicator light will be on. Speak into the microphone with a normal voice tone.
- Receive a call: After releasing the [PTT] key, the radio is in a receivable state. When receiving a call, the green indicator light will be on.
Emergency Alarm
The emergency alarm function allows the terminal to initiate an alarm to seek help. In standby mode, press the preset [SOS] key to enable or disable this function.
Flashlight
In standby mode, press the preset 8 key to turn the flashlight on or off.
FM Radio Function
Set the [SK1] key to the radio function via Menu >> Radio Set >> Press SK1. Turn on the radio and press the SK1 key [FM Radio] to enter radio mode. The screen will display the tuning frequency.
- Press ▲/▼ key to search for radio channels at the preset step frequency.
- Press the [#] key to search for radio channels automatically (screen displays 'SEEK...').
- Press [EXIT] key to switch frequency band between 65.0/75.0MHz.
- Press SK1 key [FM Radio] to exit radio mode.
Monitor
Press and hold the pre-programmed [Monitor] key to enter monitor mode and listen for weak signals or adjust volume. Release the [Monitor] key to exit.
Frequency Search
Press the pre-programmed [SEARCH] key or press and hold 8 key. The radio enters frequency search state, displaying "SEARCH...". Press [#] key to switch the searching band (VHF/UHF, etc.). The frequency and CTCSS/DCS code will be displayed after searching is completed. Press [MENU] to save the channel.
Reverse Frequency Function
Short press the [*] key in relay mode to invert the receive and transmit frequencies. The screen shows the 'R' icon. This function is useful in repeater channels when there is a frequency difference between receive and transmit frequencies.
Talk Around Function
In repeater mode, press [*] to switch between Talkaround Mode and Repeater Mode. The screen displays 'T' icon for Talkaround and 'R' icon for Repeater. In Talkaround mode, the receive frequency equals the transmit frequency.
Repeater Activation Tone
Turn on the radio, press and hold the [PTT] key, then press the [SK1] to transmit a 1750Hz audio tone to activate a repeater in hibernation.
Voice-Activated Transmit (VOX)
Enable VOX to transmit automatically when speaking, without pressing the PTT key. Transmission stops automatically when speech ceases.
- In Standby status, press [MENU][2][MENU][4] to enter Vox Switch.
- Press [MENU][2][MENU][5] to enter Vox Level. Press ▲/▼ to select VOX level (1-9). A smaller value indicates higher sensitivity. The 'V' icon will display. Default is off.
- Press [MENU] to save the setting and return to the upper menu.
- To turn off VOX, repeat the above operation and select OFF.
Dual Watch
In Dual Watch mode, the radio can receive frequencies set for both channel A and B.
- Press [MENU] [2] to enter Radio Set.
- Press [MENU] + ▲/▼ to select "15 Dual Watch".
- Press [MENU] key to enter Dual Watch Setting, press ▲/▼ key to select "On".
- Press [MENU] key to save. The 'D' icon will display.
- To turn off, repeat and select "Off".
Stopwatch Function
Press and hold the [MENU] key to enable the stopwatch function.
- Press [MENU] to start.
- Press [MENU] again to stop.
- Press [EXIT] to exit.
Weather Radio/Scan Weather Channel
Your radio has NOAA Weather Radio and NOAA Weather Scan functions to receive weather reports from designated NOAA stations.
- To turn on NOAA Weather Scan, press and hold the [0] key for 3 seconds. The _ icon appears, and the radio enters Weather band mode.
- Press and hold the [#] key for 3 seconds to start automatic scanning of all 10 channels. Press and hold [#] again to stop the scan.
- After stopping the scan, you can manually select the weather channel using the ▲ or ▼ key.
- To exit Weather Radio broadcast mode, press the _ key or [PTT] key.
Weather Channel Frequencies and Names
| Channel Number | RX Frequency MHz | Channel Number | RX Frequency MHz |
|---|---|---|---|
| CH-01 | 162.550 | CH-06 | 162.500 |
| CH-02 | 162.400 | CH-07 | 162.525 |
| CH-03 | 162.475 | CH-08 | 161.650 |
| CH-04 | 162.425 | CH-09 | 161.775 |
| CH-05 | 162.450 | CH-10 | 163.275 |
Note: Weather Channels Wx 1 Thru 10 are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.
Using Menu Functions
Basic Use with Arrow Keys
- Press [MENU] to enter the menu.
- Use ▲/▼ buttons or the encoder to navigate menu items.
- Press [MENU] again to select the desired menu item.
- Use ▲/▼ buttons or the encoder to select the desired parameter.
- To confirm, press [MENU] to save and return to the main menu. To cancel, press [EXIT] to reset and exit the menu.
- To exit the menu at any time, press [EXIT].
Using Menu with Shortcuts
- Press [MENU] to enter the menu.
- Use the numerical keypad to enter the number of the menu item.
- To enter the menu item, press [MENU].
- For parameters, use arrow buttons or the numerical shortcut code.
- Confirm with [MENU] or cancel with [EXIT].
- To exit the menu at any time, press [EXIT].
6. Wireless Programming
The Baofeng 5R Mini supports wireless programming via a dedicated mobile application. Before programming, you need to install the APP program on your smartphone.
Download Radio APP
Scan the QR codes below to download the official programming application for your device:
After opening the APP, allow Bluetooth and location services on your phone. Select the "5Rmini Series" walkie-talkie model, connect the radio, and click "Walkie-talkie". A successful connection will be prompted, and you will return to the home page.
Wireless Programming Operations
- Read the radio data: After finishing frequency reading, click the program to enter program details. In the program details interface, you can program channel information, frequency mode, and optional functions.
- Save Profile: The programmed profile allows you to save the profile as a new profile and name it. If you select "Replace Program", click "Replace Program" and save.
- Write data to radio: From the home page, select "program", then click 'Write' to enter write frequency. The radio will restart automatically once writing is complete.
7. Troubleshooting
If you encounter issues with your Baofeng 5R Mini, try the following common troubleshooting steps:
| Problem | Possible Solution |
|---|---|
| Radio does not turn on | Ensure the battery is fully charged and properly attached. Check the Volume/Power knob is turned clockwise. |
| No signal or poor reception | Check antenna connection. Ensure you are on the correct frequency/channel. Adjust squelch level. Move to an area with better line-of-sight. |
| Cannot transmit | Verify you are on a transmit-enabled channel (not a NOAA channel). Check if the keypad is locked. Ensure battery has sufficient charge. |
| Keypad unresponsive | Unlock the keypad by pressing and holding the [*] key. |
| Distorted audio | Adjust volume. Check microphone position during transmission. Ensure no interference from other electronic devices. |
| Radio gets hot during use | Continuous transmission for long periods can cause heat. Allow the radio to cool down. Avoid transmitting without an antenna. |
8. Technical Specifications
| Feature | Specification |
|---|---|
| Receiver Frequency | FM 76-108 MHz; AM 108-136MHz; VHF 136-174MHz, UHF 400-520MHz, 350-390MHz |
| Transmission Frequency | VHF 144-148MHz, UHF 420-450MHz |
| Channel Spacing | 25.0KHz (Wide)/12.5KHz (Narrow) |
| Memory Channel | 999 Groups |
| Operation Voltage | DC 7.4 V ±10% |
| Dimensions (No antenna) | 108mm × 52mm × 37mm |
| Weight (Battery pack included) | 200g |
| Transmission current | ≤1600mA |
| Receive Sensitivity | 0.25µV (12dB SINAD) |
| Rated Audio Power Output | 1W @16 ohms |
| Receive current | ≤380mA |
| Connection for accessories | 2 pin Kenwood jack |
| Antenna impedance | 50 Ohm |
Note: All specifications may be modified without prior notice or liability.
9. User Tips
- Optimize Battery Life: To prolong battery life, avoid overcharging and operate the radio within the recommended temperature range (5°C to 40°C). Turn off the radio when charging.
- Antenna Care: Always ensure the antenna is securely attached before transmitting. Never transmit without an antenna, as this can damage the radio.
- Clear Communication: When transmitting, hold the microphone 2.5-5 cm from your mouth and speak in a normal tone for best audio clarity.
- Customization: Utilize the SK1 customizable function keys for quick access to frequently used features like FM Radio, Scan, or Flashlight.
- Wireless Programming: Take advantage of the Bluetooth programming feature for easy channel management and setting adjustments via the mobile app.
10. Warranty and Support
Your Two Way Radio is an electronic product of exact design and should be treated with care. The suggestions below will help you to fulfill any warranty obligations and to enjoy this product for many years.
- Unauthorized Modifications: Do not attempt to open, disassemble, modify, or repair the radio or its accessories without authorization. The radio's precision mechanics and electronics require specialized equipment. Unauthorized opening or realignment of the transceiver will void the warranty.
- Environmental Care: Do not store the radio under direct sunlight or in hot areas, as high temperatures can shorten the life of electronic devices and warp plastics. Keep the radio dry; rainwater or dampness will corrode electronic circuits. Avoid dusty and dirty areas.
- Malfunction: If the radio emits a peculiar smell or smoke, immediately shut off its power and remove the charger or battery.
- Product Information: For further assistance or replacement parts (e.g., antenna), please contact your local dealer.
The accuracy and completeness of the contents are sought in the process of compilation, but we do not bear any responsibility for possible errors or omissions. With continuous technological development, we reserve the right to change the design and specification of the product without notice. No copy, modification, translation, and dissemination of this handbook may be made in any form without the prior written authorization of our department.
11. Regulatory Information
EU Regulatory Conformance
As certified by the qualified laboratory, this product complies with the essential requirements and other relevant provisions of Directive 1999/5/EC (2014/53/EU). All applicable EU regulations are regarded (2006/66/EC, 2011/65/EU, 2012/19/EU). This information is applicable to EU countries only.
FCC Part 15 / IC Compliance
FCC Part 15 Compliance: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
IC Compliance: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Cet appareil est conforme aux normes RSS exemptes de licences d'Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas causer d'interférences nuisibles et (2), il doit pouvoir accepter les interférences, incluant celles pouvant nuire à son fonctionnement normal. Tout changement ou modification non approuvé expressément par la partie responsable pourrait annuler le droit à l'utilisateur de faire fonctionner cet équipement.
FCC RF Exposure
WARNING! It is up to the user to properly operate this radio transmitter to ensure safe operation. Please adhere to the following:
- Do not use the radio with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result.
- Contact your local dealer for a replacement antenna.
Hand-Held Operation (Held-to-Face)
This device was evaluated for typical hand-held (held-to-face) operations with a 1-inch spacing from the front of the radio. For hand-held operation, the radio should be held 1 inch from the user's face to comply with FCC RF exposure requirements.
Body-Worn Operation
This device was evaluated for body-worn operations with the supplied belt-clip accessory. All necessary accessories are included in the package; any additional or optional accessories are not required for compliance with the guidelines. Third-party accessories (unless approved by the manufacturer) should be avoided as these might not comply with FCC RF exposure guidelines.
For body-worn operation, this device has been tested and meets the Industry Canada RF exposure guidelines when used with our company accessories supplied or designated for this product. Use of other accessories may not ensure compliance with Industry Canada RF exposure guidelines.
Fonctionnement de l'appareil, lorsque porté sur le corps. Cet appareil a été testé et s'est avéré conforme aux normes d'Industrie Canada et approuvé pour le port sur le corps à l'aide des accessoires notre société inclus et conçus pour cet appareil. L'utilisation d'accessoires ne respectant pas les exigences d'exposition RF d'Industrie Canada doit être évitée.