Sea YF-G1

Contents

Sea YF-G1 Water Flow Sensor Instruction Manual

Model: YF-G1

1. Introduction

This manual provides essential information for the safe and effective installation, operation, and maintenance of your Sea YF-G1 Water Flow Sensor. Please read this manual thoroughly before using the device and keep it for future reference.

2. Product Overview

2.1 Features

  • Suitable for petrochemical industry, community flow control, water plants, and farmland garden irrigation.
  • High sensitivity, waterproof, heat-resistant, pressure-resistant, and cold-resistant design.
  • Simple structure for easy installation and operation.
  • Constructed from high-quality plastic for strong corrosion resistance, durability, light weight, and good insulation.
  • Versatile for use in central air conditioning systems and swimming pool flow metering.

2.2 Components

The Sea YF-G1 Water Flow Sensor consists of a main plastic body with G1 inch male threaded inlet and outlet ports, an internal Hall effect sensor, and a 3-wire electrical connector.

Sea YF-G1 Water Flow Sensor
Figure 1: Main view of the Sea YF-G1 water flow sensor, showing the G1 inch male threads, the main body with product label, and the 3-wire connector.
Flow Sensor in application
Figure 2: Contextual image showing the flow sensor in an application setting, highlighting its use in various industries.

3. Setup

3.1 Mechanical Installation

  1. Ensure the water supply is turned off and the system is depressurized before installation.
  2. Identify the desired installation point in your piping system. The sensor features G1 inch male threads for connection.
  3. Observe the flow direction arrow located on the bottom of the sensor body. Install the sensor so that the water flow matches this arrow.
  4. Apply appropriate thread sealant (e.g., PTFE tape) to the sensor threads.
  5. Carefully screw the sensor into the pipeline connections. Do not overtighten to avoid damaging the plastic body.
  6. Ensure all connections are watertight before proceeding.
Flow Direction Arrow
Figure 3: Bottom view of the Sea YF-G1 water flow sensor, clearly showing the flow direction arrow.

3.2 Electrical Connection

The sensor operates on a DC5-24V power supply and has a 3-wire connector. Connect the wires as follows:

  • Red Wire: Connect to DC Power Supply Positive (VCC, +5V to +24V)
  • Black Wire: Connect to Ground (GND)
  • Yellow Wire: Connect to Signal Output (Pulse Output)

Ensure all electrical connections are secure and insulated to prevent short circuits or water ingress.

4. Operating Instructions

The Sea YF-G1 water flow sensor generates a series of electrical pulses, the frequency of which is directly proportional to the rate of water flow. The pulse characteristic is given as F=1xQ, where F is the pulse frequency and Q is the flow rate. To measure flow, you will need an external microcontroller or pulse counter to read these signals.

  1. Once installed and wired, turn on the water supply and the DC power to the sensor.
  2. The sensor will begin outputting pulses on the yellow signal wire as water flows through it.
  3. Connect the yellow signal wire to a suitable input on your data acquisition system (e.g., a microcontroller's interrupt pin).
  4. Program your system to count the pulses over a specific time interval to determine the pulse frequency.
  5. Use the provided pulse characteristic (F=1xQ) to convert the measured frequency into a flow rate. Note: The '1' in the formula is a calibration factor; specific units for Q (e.g., L/min) should be determined through calibration or detailed specifications from the manufacturer if available.

5. Maintenance

  • Regular Inspection: Periodically check the sensor for any signs of leaks, physical damage, or corrosion.
  • Connection Check: Ensure all mechanical and electrical connections remain secure.
  • Cleaning: If the sensor is exposed to water with high particulate matter, internal components may become fouled, affecting accuracy. If a decrease in accuracy is observed, the sensor may need to be removed and carefully flushed with clean water. Avoid using harsh chemicals or abrasive tools.
  • Winterization: In freezing conditions, ensure the sensor and connected pipes are drained to prevent damage from ice expansion.

6. Troubleshooting

  • No Pulse Output:
    - Check if the DC power supply (5-24V) is correctly connected to the red and black wires.
    - Verify that water is actually flowing through the sensor.
    - Inspect the yellow signal wire connection to your reading device.
  • Inaccurate Readings:
    - Ensure the sensor is installed in the correct flow direction (refer to the arrow on the sensor body).
    - Check for any blockages or debris inside the sensor that might impede the internal rotor.
    - Verify the calibration factor used in your calculation (F=1xQ).
  • Leaks at Connections:
    - Turn off water supply and depressurize the system.
    - Re-apply thread sealant and re-tighten connections. Do not overtighten.

7. Specifications

ParameterValue
Item TypeFlow Sensor
MaterialPlastic
ModelYF-G1
Interface SizeG1 inch male thread
Flow Range2-100 L/min
Working VoltageDC5-24V
Pulse CharacteristicsF=1xQ
Withstand Voltage Range≤2MPA

For a downloadable version of these specifications and instructions, please refer to the official user manual PDF: Sea YF-G1 User Manual (PDF)

8. User Tips

No specific user tips were available from customer reviews or Q&A for this product.

9. Warranty & Support

For warranty information, technical support, or service inquiries, please contact your point of purchase or the manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.