Introduction
This manual provides detailed instructions for the safe and efficient use of your 2 Channel 48V Phantom Power Supply. This universal 48V phantom power supply is designed to provide stable power for condenser microphones, supporting dual microphones simultaneously. It is suitable for a wide range of 48V vibrating membrane condenser microphones available on the market, offering high stability, balance, and output.
Safety Information
Please read the following safety manual and use steps before using this product:
- Do not expose the equipment to rain, fire, or liquids.
- Do not insert any foreign objects into the device.
- Do not attempt to repair the equipment or open the casing without professional help.
- Ensure good ventilation to prevent overheating damage to the product.
- Verify device compatibility before use.
- Always power off the unit before installation or making connections to ensure environmental safety.
Package Contents
Carefully unpack your phantom power supply and check for the following items:
- 1 x Phantom Power Supply Unit
- 1 x 3.5mm Audio Cable (0.8 m)
- 1 x USB Power Cable (1.5 m)
Setup
Follow these steps to set up your phantom power supply:
- **Power Off**: Ensure the phantom power supply and all connected audio equipment are powered off before making any connections.
- **Connect Microphones**:
- Connect your condenser microphones to the "IN" XLR ports (MIC 1 IN, MIC 2 IN) on the rear panel of the phantom power supply.
- **Connect Audio Output**:
- Connect the "OUT" XLR ports (MIC 1 OUT, MIC 2 OUT) to your audio mixer, interface, or recording equipment.
- Alternatively, use the 3.5mm audio cable to connect the "MIC1&MIC2 OUT" jack to your audio device for combined output.
- **Connect Power**: Connect the provided USB power cable to the "DC 5V" port on the rear panel and plug the other end into a suitable 5V USB power source.
Operating Instructions
Once the unit is set up, follow these steps to operate it:
- **Power On**: Press the main "POWER" button on the front panel. The corresponding LED indicator will light up. The unit features a soft and slow start function to prevent impact sounds when powering on.
- **Activate Phantom Power**: For each connected condenser microphone, switch the individual "ON/OFF" toggle switch (MIC1 or MIC2) to the "ON" position. The respective LED indicator (LED1 or LED2) will illuminate, indicating that 48V phantom power is being supplied to the microphone.
- **Adjust Audio Levels**: Adjust the input gain on your mixer or audio interface as needed for optimal sound quality.
- **Power Off**: When finished, switch the individual microphone power switches to "OFF", then press the main "POWER" button to turn off the unit.
Maintenance
To ensure the longevity and optimal performance of your phantom power supply:
- **Cleaning**: Use a soft, dry cloth to clean the exterior of the unit. Do not use liquid cleaners or solvents.
- **Ventilation**: Always ensure that the ventilation openings are clear and unobstructed to prevent overheating.
- **Storage**: Store the unit in a cool, dry place away from direct sunlight and extreme temperatures when not in use.
- **Handling**: Avoid dropping or subjecting the unit to strong impacts.
Troubleshooting
If you encounter issues with your phantom power supply, refer to the following common problems and solutions:
- No Power / Unit Not Turning On:
-
- Ensure the USB power cable is securely connected to both the unit's DC 5V port and a working 5V USB power source.
- Verify that the power source is active.
- No Sound from Microphone:
-
- Confirm that the phantom power supply is powered on (main POWER LED illuminated).
- Ensure the individual MIC ON/OFF switch for the connected microphone is in the "ON" position (corresponding LED illuminated).
- Check all XLR and 3.5mm audio cable connections for security and correct orientation.
- Verify that your condenser microphone requires 48V phantom power.
- Test with a different microphone or cable if possible.
- Humming or Noise in Audio:
-
- The unit features a stable voltage doubler filter circuit and a built-in low-pass filter design to effectively filter out AC signal interference and external audio equipment noise.
- Ensure all cables are properly shielded and not running parallel to power cables.
- The improved shielding technology and external power supply with shielding magnetic help isolate AC electromagnetic waves.
- Try using different cables or power outlets to rule out external interference.
Specifications
| Feature | Description |
|---|---|
| Brand Name | konsenda |
| Model Number | RU-2P48V |
| Item Type | Power Supply (Phantom Power) |
| Material | Metal |
| Channels | 2 (Supports dual microphones) |
| Phantom Power Output | 48V DC |
| Input/Output | Balanced XLR (IN/OUT), 3.5mm Audio Out |
| Filtering | Stable voltage doubler filter circuit, built-in low-pass filter |
| Start-up Function | Soft and slow start |
| Shielding | Improved shielding technology with magnetic isolation |
| Package Dimensions (approx.) | 10 cm (Length) x 15 cm (Width) x 6 cm (Height) |
| Package Weight (approx.) | 0.7 kg |
User Tips
- **Quality Assurance**: Users have reported satisfaction with the product's quality and performance. Ensure all connections are firm for optimal results.
- **Cable Management**: Keep audio cables organized and away from power cables to minimize potential interference, even with the unit's built-in shielding.
- **Compatibility Check**: Always confirm that your condenser microphone specifically requires 48V phantom power before connecting.
Warranty and Support
For detailed warranty information, technical support, or further inquiries, please refer to the official user manual PDF provided by the manufacturer. You can access the PDF document here.