Veise KS02A Fingerprint Door Lock

Introduction

The Veise KS02A Fingerprint Door Lock is an advanced electronic deadbolt designed to provide secure and convenient access to your home. This lock offers multiple unlocking methods including fingerprint recognition, PIN codes, and traditional mechanical keys. It is built for durability and ease of use, featuring auto-locking capabilities and a robust design suitable for wooden doors.

Safety Information

• Ensure all components are securely installed before use.
• Keep mechanical keys in a safe location away from the lock and accessible only to trusted individuals.
• Avoid exposing the lock to extreme temperatures or direct water spray, despite its IP54 rating, to prolong its lifespan.
• Do not use abrasive cleaners or solvents on the lock's surface.
• Replace batteries promptly when a low battery alert is indicated to prevent lock-out.

Package Contents

Please check the package to ensure all items are present:

• Veise KS02A Fingerprint Door Lock (Exterior and Interior Assemblies)
• Deadbolt Latch
• Strike Plate and Reinforcement Plate
• Mounting Screws
• Mechanical Keys (2 included)
• Installation Template
• User Manual (this document)
• Batteries (may or may not be included, check packaging)

Specifications

Setup

1. Installation

The Veise KS02A lock is designed for drilling installation. A screwdriver is typically sufficient to complete the installation in a few minutes. Refer to the included installation template for precise drilling and alignment. The video below demonstrates the installation process.

General Installation Steps:

1. Prepare the door: Use the provided template to mark and drill necessary holes for the deadbolt and lock assemblies.
2. Install the deadbolt latch: Insert the latch into the door edge and secure it with screws.
3. Install the exterior assembly: Route the cable through the door and align the exterior keypad assembly.
4. Install the interior assembly: Connect the cable from the exterior assembly to the interior assembly. Secure the interior assembly with mounting screws.
5. Install batteries: Insert the required DRY BATTERIES into the battery compartment of the interior assembly.
6. Test the lock: Ensure the deadbolt operates smoothly with the thumb turn and mechanical key before programming.

2. Initial Programming (Quick Setup)

The default Master Code is 12345678. It is required that you change this to a code of your own before programming any other features. Follow the steps below for quick setup and programming:

Important Notes:

• Beeps only sound when Silent Mode is disabled.
• If indicators flash red, your setting failed. Re-enter master mode to continue programming.

Change Master Code:

1. Press = + Master Code + =. Wait for long green lights.
2. Press 1. Wait for green light flash.
3. Enter New Master Code + =. Wait for green light flash.
4. Re-enter New Master Code + =. Succeed: Green light flash.

Operating Instructions

Unlocking the Door

• Fingerprint Unlock: Place your registered finger on the fingerprint sensor. The lock will unlock in approximately 0.2 seconds if recognized.
• PIN Password Unlock: Enter your 4-8 digit PIN code on the keypad, then press =.
• Mechanical Key Unlock: Insert the physical key into the keyhole and turn to unlock.

Programming Features

All programming requires entering the Master Code. Refer to Figure 2 (Quick Setup Guide) for a visual overview.

Add User Code:

1. Press = + Master Code + =. Wait for long green lights.
2. Press 2. Wait for green light flash.
3. Enter New User Code + =. Wait for green light flash.
4. Re-enter New User Code + =. Succeed: Green light flash.

Delete User Code:

1. Press = + Master Code + =. Wait for long green lights.
2. Press 3. Wait for green light flash.
3. Enter Unwanted User Code + =. Succeed: Green light flash.

Add Fingerprint:

1. Press = + Master Code + =. Wait for long green lights.
2. Press 4. Wait for green light flash.
3. Scan fingerprint 8 times. Each successful scan will be accompanied by a short beep. Succeed: Green light flash + A long beep.

Delete Fingerprint:

1. Press = + Master Code + =. Wait for long green lights.
2. Press 5. Wait for green light flash.
3. Scan unwanted fingerprint 1 time. Succeed: Green light flash + A long beep.

Silent Mode:

• Enable: Press = + Master Code + =. Wait for long green lights. Press 6, then 1 + =. Succeed: Silent Mode Enabled, Green light flash.
• Disable: Press = + Master Code + =. Wait for long green lights. Press 6, then 2 + =. Succeed: Silent Mode Disabled, Green light flash.

Auto Lock:

The lock features an auto-lock function that can be set to engage after a specified duration (10-99 seconds).

• Enable: Press = + Master Code + =. Wait for long green lights. Press 7, then 1 + =. Succeed: Auto Lock Enabled, Green light flash.
• Disable: Press = + Master Code + =. Wait for long green lights. Press 7, then 2 + =. Succeed: Auto Lock Disabled, Green light flash.

Set Auto Lock Time:

1. Press = + Master Code + =. Wait for long green lights.
2. Press 0. Wait for green light flash.
3. Enter New Duration Time (10-99 seconds) + =. Succeed: Green light flash.

Add One-Time Code:

1. Press = + Master Code + =. Wait for long green lights.
2. Press 9. Wait for green light flash.
3. Enter New User Code + =. Wait for green light flash.
4. Re-enter New User Code + =. Succeed: Green light flash.

Vacation Mode:

• Enable: Press = + Master Code + =. Wait for long green lights. Press 8, then =. Succeed: Vacation Mode Enabled, Green light flash.
• Disable: Enter Master Code + =. The door will open and Vacation Mode will be disabled.

Maintenance

Battery Replacement

The lock is powered by DRY BATTERIES and features a low battery alert. When the alert is active, replace all batteries promptly to ensure continuous operation and prevent being locked out. Use high-quality alkaline batteries for optimal performance and lifespan (approximately 365+ days).

Cleaning

Clean the lock's surface with a soft, damp cloth. Avoid using harsh chemicals, abrasive cleaners, or excessive moisture, especially on the keypad and fingerprint sensor, to prevent damage.

Troubleshooting

• Lock not responding: Check if the batteries are depleted. Replace them if necessary. Ensure the lock is properly installed and all connections are secure.
• Fingerprint not recognized: Ensure your finger is clean and dry. Try re-registering your fingerprint if issues persist.
• PIN code not working: Verify that you are entering the correct PIN code. Ensure the keypad is clean and free from debris. If multiple attempts fail, try using a mechanical key or re-programming the user code.
• Lock beeps continuously or flashes red: This often indicates a programming error or low battery. Refer to the programming steps and replace batteries if needed.
• Auto-lock not engaging: Check if the auto-lock feature is enabled and the duration is set correctly (10-99 seconds).

User Tips

• Regularly test all unlocking methods (fingerprint, PIN, key) to ensure they are functioning correctly.
• Consider setting up multiple fingerprints for different fingers or family members for added convenience.
• Change your Master Code and user PINs periodically for enhanced security.
• Keep the mechanical keys in a secure, yet accessible, location outside your home for emergency access.

Warranty and Support

Veise products are manufactured to high-quality standards. For specific warranty details, please refer to the warranty card included with your product or contact Veise customer support. Keep your proof of purchase for any warranty claims.

For technical assistance or further inquiries, please contact Veise customer support through their official channels.