1. Introduction
This manual provides essential information for the installation, operation, maintenance, and safety of your RACBOX Rear Bumper Reflector Fog Light. Please read this manual thoroughly before installation and retain it for future reference.
This product is designed as an aftermarket replacement part for specific Ford Fiesta MK8 models, enhancing visibility and maintaining the aesthetic integrity of your vehicle's rear lighting system.
2. Product Information
Product Name: Car Rear Bumper Light
Model: Designed for Ford Fiesta MK8 (2017-2023)
This product is an aftermarket automotive part and is not an original equipment manufacturer (OEM) part. It is intended for direct replacement of existing rear bumper reflectors/fog lights.
3. Specifications
| Feature | Detail |
|---|---|
| Item Type | Rear Bumper Reflector Lens / Rear Bumper Lights Assembly |
| Material | High Quality ABS |
| Lens Color | Red |
| Bulb Included | No (Reflector only, or requires existing bulb for fog light function) |
| Placement on Vehicle | Rear, Right (Driver Side) or Rear, Left (Passenger Side) |
| Fitment | For Ford Fiesta MK8 2017, 2018, 2019, 2020, 2021, 2022, 2023 |
| Origin | Mainland China |
| Length | 18 cm (7 inches) |
| Height | 8 cm (3.1 inches) |
4. Safety & Warnings
Important Safety Information
Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Warning: Keep the device and its cord (if applicable) out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Do not expose to water or moisture beyond normal automotive use conditions.
- Always ensure the vehicle is turned off and cooled down before attempting any installation or maintenance.
- If you are unsure about any step of the installation process, consult a qualified automotive technician.
5. Setup and Installation
Installation Instructions
- Ensure the vehicle is parked on a level surface, the engine is off, and the parking brake is engaged.
- Locate the original rear bumper reflector/fog light assembly on your Ford Fiesta MK8.
- Carefully remove the original vehicle product. This may involve unclipping, unscrewing, or gently prying the old unit out. Refer to your vehicle's service manual for specific removal procedures if needed.
- Inspect the mounting area for any debris or damage. Clean the area if necessary.
- Align the new RACBOX Rear Bumper Reflector Fog Light with the mounting points.
- Install the new unit directly into the opening. Ensure it clicks securely into place or is fastened according to the original mounting method.
- If the unit functions as a fog light, ensure any wiring connections are properly reattached to the new unit (bulb not included, use existing bulb if applicable).
- Gently test the fitment to ensure it is secure and flush with the bumper.
6. Operating Instructions
This product functions as a passive reflector and/or an active fog light (if wired and bulb installed). As a reflector, it operates continuously by reflecting light from other vehicles. If used as a fog light, its operation is controlled by your vehicle's existing lighting system switch.
- Reflector Function: No user action required. It passively reflects light.
- Fog Light Function (if applicable): Activate via your vehicle's fog light switch. Ensure the bulb is correctly installed and wired.
7. Maintenance
To ensure optimal performance and longevity of your rear bumper reflector/fog light:
- Cleaning: Clean the lens regularly with a soft cloth and mild automotive soap and water. Avoid abrasive cleaners or harsh chemicals that could damage the plastic lens.
- Inspection: Periodically check the unit for any signs of damage, cracks, or looseness. Ensure it remains securely attached to the bumper.
- Bulb Replacement (if applicable): If the fog light function fails, check the bulb. Replace it with the correct type and wattage as specified by your vehicle manufacturer.
8. Troubleshooting
- Unit is loose after installation: Ensure all clips are fully engaged and the unit is properly seated in its housing. Re-check the mounting points for any obstructions.
- Fog light not illuminating (if applicable):
- Check if the bulb is properly installed and not burnt out.
- Verify all electrical connections are secure and free from corrosion.
- Check the vehicle's fuse for the fog lights.
- Lens appears foggy or discolored: This may indicate external damage or prolonged exposure to harsh elements. Ensure proper cleaning as per maintenance instructions. If severe, replacement may be necessary.
9. User Tips
- When replacing, compare the new unit with the old one to ensure all mounting tabs and contours match before attempting installation.
- For a cleaner look and better fit, ensure the surrounding bumper area is free of dirt and debris before snapping the new reflector into place.
10. Manufacturer & EU Representative Information
Manufacturer:
Guangzhou Bai Ji Tun Trading Co., Ltd, C116, No. 1489, Fanghua Road Baiyun Guangzhou, tdlaccount@126.com
EU Authorized Representative:
APEX CE SPECIALISTS LIMITED, UNIT 3D NORTH POINT HOUSE, NORTH POINT BUSINESS PARK, NEW MALLOW ROAD, CORK, T23 AT2P, IRELAND, info@apex-ce.com
11. Compliance Information
This product is an aftermarket automotive part and is not an original equipment manufacturer (OEM) part. It must not be used for illegal modifications or unauthorized purposes. The product complies with relevant national automotive parts industry standards and has undergone rigorous quality inspections prior to shipment, meeting all factory standards.
A detailed user manual in PDF format may be available for download from the seller's product page or by contacting customer support.
12. Warranty & Support
For warranty information, returns, or technical support, please refer to the terms and conditions provided by your retailer or contact the seller directly through the platform where the purchase was made. Please have your order number and product details ready when contacting support.