NMMiner ESP32-2432S028R

Contents

NMMiner NerdMiner V2 User Manual

Model: ESP32-2432S028R

1. Introduction

This manual provides essential information for setting up, operating, and maintaining your NMMiner NerdMiner V2 device. Please read these instructions carefully before using the device to ensure optimal performance and longevity.

NMMiner device with screen displaying mining statistics
NMMiner device displaying current mining statistics.

2. What's Included

Carefully unbox your NMMiner device and ensure all components are present:

  • ESP32 2.8" Touch Screen device
  • Touch Pen
  • 4PIN Cable
  • USB Cable
Diagram showing included items: ESP32 2.8 inch Touch Screen, Touch Pen, 4PIN Cable, USB Cable
Contents of the NMMiner package.

3. Setup Guide

Before starting, ensure you have your home Wi-Fi network name (SSID), Wi-Fi password, and your Bitcoin (BTC) address ready. For detailed visual guides and diagrams, please refer to the full PDF user manual available at: NMMiner User Manual (PDF).

3.1 Initial Preparation

  1. If present, carefully remove the protective film from the surface of the acrylic case.
  2. Connect the device to a power source using the provided USB cable.

3.2 Network Configuration

When powered on, the miner will first attempt to reconnect to the last Wi-Fi network it used. If it cannot connect within 15 seconds, it will automatically switch to configuration mode.

  1. Connect to Hotspot: On your computer or mobile device, connect to the Wi-Fi hotspot named nmap-2.4g.
  2. Access Configuration Page:
    • Mobile Phones: After connecting to the hotspot, your mobile phone should automatically redirect to the setup page.
    • PCs: Manually open a web browser and navigate to 192.168.4.1.
  3. Configure Wi-Fi and Mining Settings: You will see a configuration page (similar to the WiFiManager interface). Fill in the following details:
    • SSID: Enter your home Wi-Fi network name.
    • Password: Enter your home Wi-Fi password.
    • Pool URL (primary): This is the main mining pool. A common default is stratum+tcp://public-pool.io:21496.
    • Pool password (primary): Usually d=0.001 or similar, depending on the pool.
    • BTC address (primary): Enter your Bitcoin wallet address.
    • Pool URL (fallback): An optional secondary pool to use if the primary fails.
    • BTC address (fallback): Your Bitcoin wallet address for the fallback pool.
    • Time zone: Select your local time zone.
    • UI refresh interval (second): How often the screen updates (e.g., 2 seconds).
    • Screen sleep time out (second): How long until the screen turns off (0 for always on, e.g., 30 seconds).
    • Initial screen brightness (0-100): Adjust screen brightness.
    • DeviceCode & Licence: These are unique identifiers for your device; do not modify them unless instructed by support.
    • Save uptime, best diff, shares in nvs: Enable this to recover mining stats after a restart.
    • Led enable: Toggle LED indicator.
    • Rotate screen: Rotate the display 180 degrees if needed.
    • BTC price update from market: Display BTC price on screen.
    • Auto brightness: Adjust screen brightness based on ambient light.
  4. Save and Restart: Click the 'Save' button. The device will auto-restart after 10-15 seconds (no manual reset needed).

4. Operating the Device

The NMMiner device operates autonomously once configured. You can interact with it using its buttons or touch interface, depending on the model variant.

4.1 Button/Touch Functions

  • NM-CYD Model (with physical buttons):
    • Boot button (Double click): Switch to the next display page.
    • Boot button (Long press): Force configuration mode.
    • Reset button (Click): Reset the NMMiner device.
  • NM-TV Model (with touch pad):
    • Touch Pad (Short touch): Switch to the next display page.
    • Touch Pad (Long touch): Force configuration mode.
  • USB-Chain Model (with 'user' button):
    • User button (Single click): Switch to the next display page.
    • User button (Long press): Force configuration mode.
  • Bot-Chain Model (with 'boot', 'user', 'reset' buttons):
    • Boot button (Long press): Clear all status from NVS (Non-Volatile Storage).
    • User button (Long press): Force configuration mode.
    • Reset button (Click): Reset the NMMiner device.

4.2 Monitoring

You can monitor your miner's performance directly on its display. For centralized monitoring, NMMiner provides an NMController. A tutorial for this can be found at: NMController Tutorial.

Screenshot of a mobile app showing 'Public Pool' mining statistics including worker ID, best difficulty, uptime, and hash rate graph.
Example of mobile monitoring interface for a mining pool.

5. Maintenance

The NMMiner device requires minimal maintenance.

  • Cleaning: Use a soft, dry cloth to gently wipe the screen and casing. Avoid abrasive cleaners or solvents.
  • Environment: Operate the device within its specified temperature range (-20 to 70 °C) and avoid high humidity or direct sunlight.
  • Firmware Updates: Periodically check for firmware updates to ensure optimal performance and access to new features. Updates can typically be found on the official NMMiner firmware page: flash.nmminer.com.

6. Troubleshooting

  • Device Not Connecting to Wi-Fi: Double-check your Wi-Fi SSID and password in the configuration settings. Ensure the device is within range of your Wi-Fi router.
  • Screen Stuck at 70% During Boot: This may indicate a firmware issue or a problem during initialization. Try resetting the device. If the issue persists, consider performing a firmware update.
  • Low Hash Rate or No Shares:
    • Ensure your BTC address is correctly entered.
    • Verify the mining pool URL and password are correct.
    • Pool Rejections: Due to limited chip resources, high-difficulty mining pools may reject shares. It is recommended to use low-difficulty pools. Supported low-difficulty pools include:
      • stratum+tcp://public-pool.io:21496 (Type: tcp, Port: 21496, Description: BTC, Min. Difficulty: 0.001)
      • stratum+tcp://pool.tazmining.ch:33333 (Type: tcp, Port: 33333, Description: BTC, Min. Difficulty: 0.001)
  • Device Unresponsive: Perform a hard reset by disconnecting and reconnecting the USB power cable. If buttons are available, use the 'Reset' function.

7. Specifications

FeatureDetail
Model NumberESP32-2432S028R
Master ChipESP32D0 / ESP32S3, Xtensa32 dual core processor
MCULow-power dual-core 32-bit CPU
HashRate1000+ Kh/s (ESP32D0WD), 380+ Kh/s (ESP32S3)
Wi-Fi802.11 b/g/n, up to 150Mbps
Transmission Rate10/100Mbps
Device ManagementNMController
Firmware UpgradeNM Flash ESPTool (flash.nmminer.com)
Power InterfaceType-C USB
Supply ModeUSB
Power Consumption0.5-1W (0.8W typical)
Operating Temperature-20 ~ 70 °C
Screen Size2.8 Inch
SRMBuilt-in 520 KB SRAM
CaseAcrylic Case
Weight0.15KG
Dimensions (approx.)85mm x 60mm x 14mm
FunctionNMMiner, Nerdminer v2
Diagram showing device dimensions: 85mm length, 60mm width, 14mm height.
Approximate dimensions of the NMMiner device.

8. User Tips

  • Wallet Address: Always double-check that you have entered your correct Bitcoin wallet address during setup to ensure any potential rewards are sent to you.
  • Firmware Updates: Keep your device's firmware updated to benefit from performance improvements and bug fixes.
  • Setup Accuracy: Follow the setup instructions precisely, especially when entering Wi-Fi credentials and pool details.
  • Dual Purpose: Many users enjoy using the NMMiner as a unique digital clock or desk ornament while it performs its mining function in the background.
  • Expectation Management: This device is often referred to as a 'lucky miner' or 'lottery miner'. While it performs real mining operations, the chance of solo mining a block is extremely low. It is primarily for educational purposes and the enjoyment of participating in the Bitcoin network.

9. Warranty and Support

For any issues not covered in this manual, or for warranty inquiries, please contact your seller directly. Ensure you have your purchase details available. For technical support related to firmware or advanced configurations, refer to the official NMMiner resources, including the firmware update page: flash.nmminer.com.

© NMMiner. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.