coolo Raindrop Detection Sensor

Contents

Tuya Smart Zigbee Raindrop Detection Sensor User Manual

Model: Raindrop Detection Sensor

1. Introduction

Thank you for choosing the Tuya Smart Zigbee Raindrop Detection Sensor. This device is designed to provide reliable outdoor rainwater detection and integrate seamlessly into your smart home automation system. Please read this manual thoroughly before installation and use to ensure proper operation and to prevent damage.

Important Safety Information:

  • Read all instructions carefully before use.
  • Do not attempt to disassemble or modify the device.
  • Ensure the device is installed in a location where it will not be physically damaged.
  • Use only the specified battery type (CR123A).

2. Package Contents

Please check the package for the following items:

  • Raindrop Detection Sensor Unit
  • Installation Base
  • User Manual (this document)
  • (CR123A battery may or may not be included, please check packaging)

3. Setup and Installation

3.1. Battery Installation

  1. Gently push upwards to open the battery back cover of the sensor unit.
  2. Insert one CR123A 3V battery into the battery compartment, ensuring correct polarity.
  3. Close the battery back cover securely.
Diagram showing Zigbee Raindrop Detection Sensor connecting to a Zigbee Gateway, WiFi Router, and APP Control.

Figure 1: System Overview - The sensor requires a Zigbee Gateway (not included) to connect to your WiFi network and be controlled via the app.

3.2. Network Configuration (Pairing)

The sensor operates on the Zigbee protocol and requires a Zigbee gateway (not included) to function with your smart home system.

  1. Ensure your Zigbee gateway is powered on and in pairing mode (refer to your gateway's manual for specific instructions).
  2. On the Raindrop Detection Sensor, press and hold the reset button for 3 seconds, then release. The red LED indicator will start flashing, indicating the sensor is in network configuration (pairing) mode.
  3. Open your smart home app (e.g., Tuya Smart, Smart Life, or Home Assistant with Zigbee2MQTT) and select your Zigbee gateway. Follow the app's instructions to add a new device.
  4. During the binding process, keep the sensor as close as possible to the Zigbee gateway for a stable connection.
  5. Once successfully paired, the red LED indicator will stop flashing.

Compatibility: This product is compatible with Tuya Zigbee gateway (optional), ewelink Zigbee gateway, Yandex Zigbee speaker, and Home Assistant (ZHA, Zigbee2mqtt).

3.3. Physical Installation

The sensor is IPX4 waterproof and designed for outdoor use.

  1. For Window Sill Installation:
    • Use double-sided adhesive tape (not included) to securely fix the installation base onto the window sill.
    • Place the sensor unit into the installation base.
    • For added security, a screw can be inserted through the base into the window sill (if applicable and safe to do so).
  2. For Window Glass Installation (without sill):
    • Use double-sided adhesive tape to stick the side of the sensor device directly to the outer window glass surface.
    • Ensure the sensor is positioned so it will not be hit or obstructed when opening or closing the window.

Important: When applying double-sided tape, ensure you do not block the drainage hole located on the sensor base.

Image showing the IPX4 waterproof sensor installed outdoors during rain, with a smartphone displaying 'Raining' status.

Figure 2: Outdoor Installation - The sensor is IPX4 rated for outdoor use in rainy conditions.

4. Operating Instructions

4.1. Raindrop Detection and Notifications

Once installed and paired, the sensor will detect raindrops on its surface. When rain is detected, it will send a notification to your linked smart home app.

Smartphone screen showing a 'Rain sensor' app interface with battery percentage, sensitivity slider, illuminance sampling setting, and a toggle for 'Detected raindrops' message push.

Figure 3: App Notification Example - Receive instant alerts on your smartphone when raindrops are detected.

4.2. Light Sensor Functionality

The sensor also includes a light sensor to measure ambient illuminance. This data can be viewed in your smart home app and used for automation routines (e.g., turning on lights when it gets dark).

4.3. App Remote Control and Settings

You can monitor the sensor's status and adjust settings remotely via your smartphone app.

  • Sensitivity Adjustment: The detection sensitivity can be adjusted within the app. A higher sensitivity value means the sensor will detect rain more readily. This feature is supported by Smart Life App and Zigbee2mqtt.
  • Illuminance Sampling Interval: You can set how frequently the light sensor takes readings (e.g., from 1 to 480 minutes).
  • Message Push: Enable or disable push notifications for detected raindrops.
  • Battery Status: Monitor the battery percentage directly from the app.
Smartphone app screen showing 'Illuminance Sampling' setting with a slider to select values from 1 to 480 minutes.

Figure 4: Illuminance Sampling Setting - Customize the frequency of light sensor readings.

A woman using a smartphone with the rain sensor app open, showing remote monitoring capabilities.

Figure 5: Remote Control - Access sensor data and settings anytime, anywhere.

5. Maintenance

  • Cleaning: Periodically clean the sensor surface with a soft, damp cloth to ensure optimal raindrop detection. Avoid using abrasive cleaners or solvents.
  • Battery Replacement: When the battery level is low (indicated in the app), replace the CR123A battery following the instructions in Section 3.1. The battery life is typically over 24 months.
  • Inspection: Regularly check the physical installation to ensure the sensor is securely mounted and free from obstructions or damage.

6. Troubleshooting

ProblemPossible CauseSolution
Sensor not detecting rain
  • Sensor surface is dirty.
  • Sensitivity setting is too low.
  • Battery is low or depleted.
  • Clean the sensor surface.
  • Increase sensitivity in the app.
  • Replace the CR123A battery.
Sensor not connecting to gateway/app
  • Sensor is too far from the gateway.
  • Gateway is not in pairing mode.
  • Battery is low.
  • Move sensor closer to the gateway.
  • Ensure gateway is in pairing mode.
  • Replace the CR123A battery.
  • Re-initiate pairing process (Section 3.2).
No notifications received
  • Message push is disabled in app.
  • App notifications are blocked by phone settings.
  • Enable message push in the sensor's app settings.
  • Check your phone's notification settings for the smart home app.

7. Specifications

FeatureDetail
Product NameRaindrop Detection Sensor
Wireless ProtocolZigbee 3.0 (Wi-Fi optional, depending on model)
Working VoltageDC 3.0V
Battery TypeCR123A
Standby Current<10uA
Battery Life>24 months
Illuminance Sensor Range0-4000Lux
Working Temperature-10°C to 60°C
Waterproof LevelIPX4
Product Dimensions59mm x 33mm x 40mm

8. User Tips

  • Battery Type: The sensor uses a non-rechargeable CR123A battery. Do not attempt to charge it; replace it when depleted.
  • Gateway Proximity: For best performance and reliable connection, try to keep the sensor within a reasonable range of your Zigbee gateway, especially during initial pairing.
  • Automation Ideas: Combine the raindrop detection with other smart devices. For example, automatically close smart windows or retract awnings when rain is detected. Use the light sensor to trigger outdoor lighting at dusk.

9. Warranty and Support

For warranty information and technical support, please refer to the documentation provided by your retailer or contact the manufacturer directly. Keep your proof of purchase for warranty claims.

For further assistance, you may also consult the official product page or support forums related to Tuya Smart devices.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.