Introduction
Dear Gamer,
Thank you for purchasing the NYXI Wizard 2 Wireless Controller. Before you use the product, please read this manual carefully to ensure proper setup and optimal performance.
Package Contents
- NJ10 Left Controller ×1
- NJ10 Right Controller ×1
- NJ10 Middle Bridge ×1
- Multi-function Receiver ×1
- USB-C Charging Cable ×1
- Receiver Extension Cable ×1

Technical Specifications
| Feature | Specification |
|---|---|
| Connectivity | Bluetooth 5.0, 2.4G Wireless |
| Battery Capacity | 400mAh (per controller) |
| Charging | 5V/0.4A via USB-C |
| Materials | PC + ABS + Metal + Silicone |
| Weight | 225g |
| Size | 106*155*65.5mm |
| Joystick Sensor Module Brand/Type | K-SLIVER |
| Trigger Button Type | Linear |
| Compatible Platforms | Nintendo Switch, Nintendo Switch 2, PC, Android, iOS |
| Compatible Nintendo Models | Nintendo Switch 2, Nintendo Switch, Nintendo Switch OLED, Nintendo Switch Lite |
| Hall Effect | Yes |
Specification Diagram

Setup and Connection
Connecting to Nintendo Switch
- Slide the controller downward along the rails on both sides of the console screen until it clicks. The "Controllers" interface on the console will display connected left/right controllers.
- To remove the controller, press the release button on the back of the controller and slide it upward.
- When the console is powered on, detaching the controller from the rails will automatically establish a Bluetooth connection with the Switch.
- When the console is powered off, detach the controller from the rails and press the Home Button to power on and reconnect.
- After successfully connecting to Switch, the controller vibrates for 1 second.

Receiver Connection to PC (Xinput Mode)
- Press and hold the Home Button for 3 seconds to power on. LEDs 1-4 on both controllers will flash green sequentially.
- Insert the receiver into the PC and press and hold its button until the LED blinks rapidly.
- Wait for pairing.
Receiver Connection to PC (Dinput Mode)
- In Xinput mode, press and hold A + B + Home to switch to Dinput mode. LEDs 1-4 will blink green three times.
- Repeat the same key combination to switch back to Xinput mode.
Receiver Connection to PC/NGC
- Press and hold the Home button of the right handle for 5 seconds to turn on the device, and the LED1-4 of the right handle will flash green.
- Plug the receiver into the computer, and press and hold the button on the receiver until the LED flashes quickly.
- Wait for the right handle and receiver to pair successfully, and the LED lights of the receiver and the handle will be on.
Receiver Connected to Wii
- Turn on the Wii console, enter the game, and connect the original controller.
- After entering the game, unplug the original adapter, and then plug the NJ10 receiver into the console, and press and hold the button on the receiver until the LED flashes quickly.
- Press and hold the Home button of the right handle for 5 seconds to turn on the device, and the LED1-4 of the right handle will flash green.
- Wait for the right handle and receiver to pair successfully, and the LED lights of the receiver and the handle will be on.
- Press the button on the receiver again until the LED flashes quickly, and long press the screen button on the left handle for 5 seconds until the left handle LED1-4 flashes green.
- Wait for the left handle and receiver to pair successfully before it can be used normally.

Calibration
Joystick Calibration
- Press SL + SR + + Button (left controller: - Button) to enter calibration mode.
- Rotate the joysticks through their full range of motion.
- Press the same keys again to exit. A 1-second vibration confirms completion.
Trigger Calibration
- Press SL + SR + Home (left controller: Capture Button) to enter calibration mode.
- Press the triggers fully.
- Exit using the same keys. A 1-second vibration confirms completion.
6-Axis Gyroscope Calibration
- On Nintendo Switch, navigate to Settings > Controllers & Sensors > Calibrate Motion Controls.
- Place the controller on a flat surface and follow the on-screen prompts. Press the - and + Buttons to complete calibration.
Advanced Features
Turbo Function
- Supported Buttons: D-pad, A, B, X, Y, L, R, ZL, ZR.
- Enable Turbo: Hold the Setting Button, press a target button, then release. LED4 will glow white.
- Adjust Speed: Default is 12Hz (adjustable via app).
- Disable Turbo: Press the Setting Button + target button three times. LED4 will turn off.
Button Programming (M1/M2 Back Buttons)
The M1/M2 back buttons can be mapped to other buttons or macros (maximum 21 actions per macro).
- Mapping: Hold the Setting Button + target back button for 3 seconds. Press the desired button/macro sequence, then press the back button again to save.
- Clear Mapping: Hold the Setting Button + back button for 3 seconds, then press the back button without any input.



User Tips
- For optimal performance, ensure your controller is fully charged before extended gaming sessions.
- Regularly check for firmware updates for your controller to benefit from new features and bug fixes.
- When experiencing connectivity issues, try re-pairing the controller with your device or restarting both the controller and the console/PC.
- Utilize the customizable back buttons for frequently used in-game actions to gain a competitive edge.
Troubleshooting
- Controller not connecting: Ensure the controller is charged. Verify the correct connection mode (Bluetooth, 2.4G wireless, Xinput, Dinput) is selected for your device. Try re-pairing following the instructions in the 'Setup and Connection' section.
- Input lag or unresponsiveness: Check for interference from other wireless devices. Ensure the receiver is connected directly to your PC/console if using 2.4G wireless. Perform joystick and trigger calibration.
- Buttons not responding: Check if the button programming has been accidentally altered. Try clearing the mapping for the affected buttons.
- Gyroscope issues: Ensure the controller is placed on a flat, stable surface during calibration.
- Turbo function not working: Verify that the turbo function is enabled for the desired button and that LED4 is glowing white.
Compliance and Safety Information
Declaration of Conformity
Model: NJ10
The product conforms to EC standards for radio interference. Shenzhen MIKE Morgen Technology Co., Ltd. declares that the NJ10 radio equipment conforms to the Directive: EN IEC 62368-1:2020+A11:2020, EN 50663:2017, EN 62479:2010, ETSI EN 301 489-1 V2.23(2019-11), ETSI EN 301 489-17 V3.2.4(2020-09), ETSI EN 300 328 V2.2.2(2019-07).
The full text of the EU Declaration of Compliance can be found on: www.nyxigame.com
FCC Statement
Model: NJ10, FCC ID: 2A88F-NJ10
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) The device may not cause harmful interference. (2) The device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class C digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the distance between the equipment and receiver.
- Plug the equipment into a socket on a circuit different from that to which the receiver is connected.
- Consult your distributor or an experienced radio/TV technician for help.
Precautions
- Do not expose the product to liquid.
- Do not disassemble the product.
- Avoid dropping the product.
- Avoid exposing the product to extremely high or low temperatures.
The symbol indicating separate collection for electrical and electronic equipment means the product should not be disposed of with household waste but be brought to an appropriate collection point to enable recycling. According to local regulations, do not dispose of the product or rechargeable battery with normal household waste. Appropriate disposal of used products and rechargeable batteries helps to prevent negative impacts on the environment and human health.
Warranty and Support
For warranty information, technical support, and further assistance, please visit the official NYXI website or contact their customer service directly. Details regarding specific warranty periods and service procedures can be found on their support pages.
Official Website: www.nyxigame.com
Product Video Overview
Watch this video for a visual guide to the NYXI Wizard 2 Wireless Controller's features and functionality.