SPEEDRACING IM-1002A-BK

Contents

SPEEDRACING Racing Intake Manifold with Fuel Rail and Throttle Body

Model: IM-1002A-BK

Brand: SPEEDRACING

1. Introduction

This manual provides essential information for the proper installation, operation, and maintenance of your SPEEDRACING Racing Intake Manifold with Fuel Rail and Throttle Body. This high-performance component is designed for specific Chevrolet, GMC, and Pontiac LS series engines to enhance engine airflow and performance. Please read all instructions carefully before proceeding with installation or use.

2. Safety & Warnings

Important Safety Information: Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Keep the device and its cord (if applicable) out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.
  • Handle with care to avoid cuts or injuries.
  • This product is intended for automotive use only.

3. Product Overview

The SPEEDRACING Racing Intake Manifold is constructed from 3 mm (1/8 inch) thick T6061 aluminum sheet, ensuring durability and resistance to bending or warping under vacuum or pulse conditions. It is available in 92mm and 102mm throttle body openings.

Silver intake manifold assembly with fuel rails, gaskets, and bolts
Figure 1: Silver intake manifold assembly with fuel rails, gaskets, and bolts.
Black intake manifold assembly with throttle body, fuel rails, gaskets, and bolts
Figure 2: Black intake manifold assembly with throttle body, fuel rails, gaskets, and bolts.

Components Included:

  • Intake Manifold (92mm or 102mm, Black or Silver)
  • Fuel Rails
  • Gaskets
  • Mounting Bolts
  • Fuel Line (braided, with AN fittings)
  • Throttle Body (if included in selected package)
Exploded view of all components included: intake manifold, fuel rails, gaskets, bolts, and fuel line
Figure 3: All components included in the package.
Close-up of a braided fuel line with AN fittings
Figure 4: Detail of the braided fuel line with AN fittings.
Detailed view of the intake manifold's internal runners and port design, highlighting the welding quality
Figure 5: Internal runner and port design of the intake manifold.

4. Specifications

Attribute Value
Manufacturer Part Number IM-1002A-BK
Other Part Number 92mm/102mm
Interchange Part Number Racing Intake Manifold w/ Fuel Rail
Special Features Racing Intake Manifold w/ Fuel Rail
OEM NO. For Chevrolet GMC Pontiac LS LS1 LS2 LS6
Placement on Vehicle Front
Material 3 mm (1/8 in) thick T6061 aluminum sheet
Item Weight 7kg
Item Length 490mm / 19.2 inches
Item Width 170mm / 6.6 inches (widest point)
Item Height 210mm / 8.26 inches
Throttle Body Opening 92mm or 102mm
Country/Region of Manufacture China
High-concerned chemical None
Dimensional diagram of the intake manifold, showing overall length (490mm/19.2"), height (210mm/8.26"), and throttle body opening diameters (92mm/3.6" and 170mm/6.6" at the widest point)
Figure 6: Dimensional diagram of the intake manifold.

5. Setup & Installation

Professional installation is strongly suggested for this product. Improper installation can lead to engine damage or personal injury.

While professional installation is recommended, the general steps for installing an intake manifold typically involve:

  1. Preparation: Disconnect the battery. Drain coolant if necessary. Remove any components obstructing access to the factory intake manifold (e.g., air intake, throttle body, fuel lines, wiring harnesses).
  2. Removal of Old Manifold: Carefully remove the existing intake manifold, ensuring all bolts, gaskets, and seals are accounted for. Clean the mating surfaces on the cylinder heads thoroughly to ensure a proper seal with the new manifold.
  3. Gasket Installation: Install new gaskets onto the cylinder head ports or the new intake manifold, as per manufacturer specifications.
  4. Manifold Placement: Carefully position the new SPEEDRACING intake manifold onto the engine. Ensure proper alignment with the cylinder head ports.
  5. Securing Manifold: Install the mounting bolts and tighten them to the manufacturer's specified torque sequence and values. This is critical for preventing vacuum leaks.
  6. Fuel Rail Installation: Install the provided fuel rails onto the intake manifold. Connect the fuel injectors (not included) and the braided fuel line. Ensure all fuel connections are secure and leak-free.
  7. Throttle Body Installation: Mount the throttle body (if included or transferred from the old manifold) to the intake manifold. Connect any necessary sensors and wiring.
  8. Reconnection: Reconnect all removed components, including vacuum lines, wiring harnesses, and the air intake system. Refill coolant if drained.
  9. Final Checks: Double-check all connections, hoses, and wiring. Ensure no tools or debris are left in the engine bay.
  10. Initial Start-up: Reconnect the battery. Start the engine and carefully check for any leaks (fuel, vacuum, coolant) or unusual noises. Monitor engine parameters.

Note: Due to variations in vehicle models and engine configurations, specific steps and torque values may differ. Always refer to your vehicle's service manual for precise instructions.

6. Operating Instructions

Once the intake manifold is correctly installed and all systems are checked, the engine can be operated normally. This racing intake manifold is designed to improve airflow, which may require engine tuning to fully optimize performance and ensure proper air-fuel ratios. Consult with a professional tuner for optimal results.

Monitor engine temperature, oil pressure, and other vital signs during initial operation after installation to ensure everything is functioning correctly.

7. Maintenance

Regular maintenance of your engine components, including the intake manifold, is crucial for longevity and performance.

  • Periodic Inspection: Regularly inspect the intake manifold, fuel rails, gaskets, and all connections for any signs of leaks, cracks, or damage.
  • Cleaning: Keep the exterior of the manifold clean. Avoid using harsh chemicals that could damage the aluminum finish.
  • Gasket Integrity: Over time, gaskets can degrade. If you notice any vacuum leaks or rough idling, inspect and replace gaskets as necessary.
  • Fuel System Checks: Periodically check the fuel lines and connections for any signs of wear or leaks.

8. Troubleshooting

If you encounter issues after installing the intake manifold, consider the following common problems and solutions:

  • Vacuum Leaks:
    • Symptom: Rough idle, poor engine performance, check engine light.
    • Solution: Re-check all manifold bolts for proper torque. Inspect gaskets for proper seating and damage. Use a smoke test or spray carb cleaner around the manifold mating surfaces to identify leaks.
  • Fuel Leaks:
    • Symptom: Smell of fuel, visible fuel drips, engine misfires.
    • Solution: Inspect all fuel line connections, fuel injector O-rings, and fuel rail seals. Ensure AN fittings are tightened correctly.
  • Engine Performance Issues (after installation):
    • Symptom: Engine running rich/lean, poor acceleration, inconsistent power.
    • Solution: This high-performance manifold may require engine tuning to optimize air-fuel ratios and ignition timing. Consult a professional tuner. Ensure all sensors are correctly reconnected.

9. User Tips

  • Fitment Verification: Always double-check compatibility with your specific vehicle model and engine year (e.g., Dodge Charger SRT 6.4HIMI 2013) before purchasing and installing.
  • Throttle Body Compatibility: If you plan to use an electric throttle body, ensure it is compatible with this manifold and your vehicle's electronic system. Modifications may be required.
  • Professional Tuning: For optimal performance gains and engine longevity, consider professional engine tuning after installing this racing intake manifold.
  • Gasket Quality: Use high-quality gaskets and ensure mating surfaces are perfectly clean to prevent vacuum leaks.

10. Warranty & Support

For any product-related inquiries, technical support, or warranty claims, please contact the manufacturer directly using the information below. Please have your model number (IM-1002A-BK) and purchase details ready.

Manufacturer Information:

Company Name: Zhejiang xuzhong automobile parts co., ltd
Full Address: No. 666, jingye road, economic development zone, rui'an city, wenzhou city, zhejiang province, China
Email: xz2014express@163.com
Telephone: +86-15888266370

EU Authorized Representative:

Company Name: SUCCESS COURIER SL
Full Address: CALLE RIO TORMES NUM. 1, PLANTA 1, DERECHA, OFICINA 3, Fuenlabrada, Madrid, 28947 Spain
Telephone: +34-910602659
Email: successservice2@hotmail.com

A user manual in PDF format may be available for download. Please refer to the official product page or contact support for more details: View User Manual (PDF)

11. Compliance Information

This product must comply with all applicable safety and regulatory requirements in the market where it is sold. Sellers are responsible for assessing which requirements and regulations apply based on the actual product type, function, and destination market.

For automotive components, compliance may involve standards related to vehicle safety, emissions, and material composition. Users should ensure that any modifications made to their vehicle comply with local laws and regulations.

© 2024 SPEEDRACING. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.