Introduction
This manual provides comprehensive instructions for assembling, operating, and maintaining your DIY Electronic Watch Kit. This kit offers a unique opportunity to engage in creative soldering and build a functional LED digital watch. Please read all instructions carefully before beginning assembly.
Note: DIY components are shipped separately; customers must provide their own soldering tools and have basic soldering skills!
Features
- Transparent shell design showcases the beauty of electronic art.
- DIY assembly of individual parts allows you to experience the fun of creative soldering.
- Red LED digital display for clear and easy reading.
- Ultra-lightweight and slim design for comfortable wear that fits snugly on the wrist.
- Available in multiple colors to showcase your personal style.
Product Components
The kit includes the following parts (battery not included):
- Microcontroller x1
- 0.28 inch LED digital tube x1
- 1K Resistor x1
- 104 Ceramic Capacitor x1
- 22 Ceramic Capacitor x2
- 32768Hz Crystal oscillator x1
- 4.5-4.5-6.5 momentary switch x2
- 1.4*8mm Self-Tapping Screw x4
- CR2032 Battery Holder x1
- Transparent plastic case (top cover) x1
- Transparent plastic shell (bottom cover) x1
- Silicone watch strap (color subject to actual item) x1
- PCB x1
- 2mm Cross screwdriver x1
Specifications
| Parameter | Value |
|---|---|
| Product Name | LED Watch Kit |
| Shipping Method | DIY Kit |
| Component Type | Through-hole components |
| Display Type | 0.28-inch red LED numeric display |
| Power Supply | 1*CR2032 button battery (not included) |
| Strap Material | Silicone strap |
| Case Dimensions (L x W x T) | 50mm x 45mm x 16mm |
| Strap Dimensions (Length, Width) | 90mm + 120mm, 20mm wide |
| Overall Length | 260mm (90 + 50 + 120) |
| Operating Temperature | -20-70℃ |
| Package | TQFP |
Assembly Instructions (Soldering Tutorial C17)
Please strictly follow these soldering requirements:
- First, check the quantity and model of the components. Use a multimeter to measure them if possible.
- Install according to the tutorial steps.
- When installing, install the shorter components first, then the taller components.
- After installing each section of components, weld that section and promptly trim the component leads.
- During welding, ensure the welding temperature is not too high and the welding time is not too long, as this may damage the circuit board or components.
- After welding, re-inspect the solder joints for quality and verify that components are installed correctly.
- During power-on testing, ensure the power supply polarity is correct (positive and negative terminals are not reversed). The voltage must not exceed 5V.
- When securing the housing with screws, ensure they are tightened properly but not over-tightened.
Detailed Steps from Tutorial Image:
Soldering Method:
The image illustrates proper soldering techniques: preheating, introducing the soldering plate, melting solder, removing the soldering iron, and checking for completion. It also shows examples of qualified, too much, too little, and cold solder joints, as well as short-circuited points.
Installation Steps:
- Install the resistor at position R1, ensuring no positive or negative direction.
- Install the crystal oscillator at Y1 position without distinguishing direction. Leave the pins longer.
- Install the microcontroller at position U1. Pay attention to the direction of the markings.
- Weld the Tact Switch at positions S1 and S2. Pay attention to the welding temperature not being too high and do not install it crooked.
- Install a 104P ceramic disc capacitor in position C3, and 22P ceramic disc capacitors in positions C1, C2, ensuring no polarity.
- Install the digital tube at the position of LED1. The decimal point is at the bottom.
- Weld the battery holder at position BT1. Ensure the opening direction is outward for battery insertion.
- Install the button battery (CR2032, not included) with the positive pole above.
- Install the circuit board into the upper casing, tilting it slightly to install the switch direction first.
- Install the bottom shell.
- Secure with 4 screws. Do not use too much force; just tighten it in place.
- Install the watch strap, press the switch, and then push the switch into the socket.
Installation Precautions:
- When installing, install the shorter components first and then the high components.
- Install a portion of the components, solder a portion of the components, and promptly cut off the component pins.
- When welding, pay attention to the welding temperature not being too high and the welding time not being too long, otherwise it may damage the circuit board or components.
- After welding, check again whether the welding points are qualified and whether the components are installed incorrectly.
- If there is a malfunction, first check if the power supply is correct, and then inspect the component installation and solder joints.
Circuit Principle:
Video Tutorial:
For a visual guide to the installation process, please refer to the official video tutorial:
Video 1: LED Watch Installation Tutorial (Model: CAI-C17).
Operating Instructions
- Display Time: Press any button (S1 or S2) to display the time. The display will automatically turn off after 10 seconds to conserve battery.
- Set Minutes: Press and hold button S1 to adjust the minutes.
- Set Hours: Press and hold button S2 to adjust the hours.
- 24-hour Format: You can set the display to 24-hour format by shorting the solder joints on the back of the PCB.
Other Functional Settings:
- Always-on Display: Short circuit the two points labeled for "Set minutes" to keep the digital tube always on.
- 24-Hour System: Short circuit the two points labeled for "Set hours" to enable the 24-hour time display system.
Maintenance
- Cleaning: Use a soft, dry cloth to clean the watch case and strap. Avoid using harsh chemicals or abrasive materials.
- Battery Replacement: When the display dims or stops working, replace the CR2032 button battery. Ensure correct polarity during installation.
- Storage: Store the watch in a cool, dry place away from direct sunlight and extreme temperatures.
Troubleshooting
- Watch not powering on or displaying correctly:
- First, verify the correct power supply (CR2032 battery installed with correct polarity).
- Inspect component installation and solder joints for any loose connections or cold solders.
- Ensure the voltage does not exceed 5V during power-on testing.
- Buttons not responding: Check the momentary switches (S1 and S2) for proper installation and soldering.
- Inaccurate time: Ensure the 32768Hz crystal oscillator is correctly installed and soldered.
User Tips
- Take your time during soldering, especially if you are new to it. Double-check each connection.
- Consider using a magnifying glass to inspect solder joints for quality.
- The transparent case allows for a clear view of the internal electronics, making it a great educational project.
Warranty & Support
For any issues, questions, or support regarding your DIY Electronic Watch Kit, please contact the seller directly through the platform where you purchased the product. Please refer to the original product listing for any specific warranty information provided by the seller.
A PDF version of the user manual is also available for download. Please refer to the product page for the link.