Viladepot D9

Contents

Viladepot Smart Lock D9 User Manual

Model: D9

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Viladepot Smart Lock D9. Please read this manual thoroughly before operating your smart lock and keep it for future reference.

Important Notes:

  • This lock is equipped with mechanical keys for manual unlocking. Please take out the mechanical keys from the package and keep them in a safe place, ensuring you always have access to them.
  • To power on the lock, four alkaline AA batteries (not included) are required. Non-alkaline and rechargeable batteries ARE NOT RECOMMENDED.
  • This lock is designed for both outdoor and indoor use and can be exposed to direct sunlight or rain. The waterproof rating is IP45.
  • Keep your fingers clean when using the fingerprint sensor on this lock.

What's in the Box

Verify that all components are present and in good condition before beginning installation.

Contents of the Viladepot Smart Lock D9 package including front panel, back panel, deadbolt, mounting plate, strike plate, latch holding box, emergency unlock keys, installation hardware, and ID cards.

Image: Contents of the Viladepot Smart Lock D9 package.

ItemDescriptionQuantity
AFront panel1 Piece
BMounting plate1 Piece
CBack panel1 Piece
DDeadbolt1 Piece
EM4 x 30mm Screws2 Pieces
FM4 x 8mm Screws2 Pieces
GBlack color M4 x 30mm Screw1 Piece
HM4 x 25mm Screws4 Pieces
JMechanical keys2 Pieces
KStrike plate1 Piece
LLatch holding box1 Piece
ID Card2 Pieces

Specifications

AttributeValue
Brand NameViladepot
Model NumberD9
MaterialAluminium Alloy
Fit Door Thickness35mm-50mm (1-3/8" to 2")
Finish TypePainted
Handle DirectionDirection Reversible (Left-handed Doors, Right-handed Doors)
Working Temperature-20°C ~ 70°C
Working Humidity20% ~ 80%RH
Power Supply6V (4 x AA Alkaline Batteries, not included)
Emergency Power SupplyTYPE-C Interface
Working Power Consumption< 250mA
Static Power Consumption< 100uA
Unlocking MethodsFingerprint, App, Card, Passcode, Mechanical Key
Doorknob FunctionBiometric, Key & Keypad
ConnectivityBluetooth
Smart Home PlatformTuya
User CapacityTotally 254 (password+card+fingerprint users, 100 fingerprint users at most)
Waterproof RatingIP45
CertificationFCC

Installation Instructions

For a visual guide, please refer to the installation video below.

Video: Step-by-step installation guide for the Viladepot Smart Lock D9.

Installation Diagram

Detailed installation diagram showing all components and their placement on the door.

Image: Detailed installation diagram and dimensions for the smart lock.

Step-by-Step Guide

  1. Drilling Holes

    • Check the required backset (60mm or 70mm).
    • Align the provided template along the vertical center line of the deadbolt (D) at the desired height, and tape it to the door.
    • Mark the holes first, then start drilling.

    Door drill hole map: 2-1/8" (54mm) for door hole, 1" (25mm) for latch hole, 2-3/8" (60mm) or 2-3/4" (70mm) backset.

  2. Install the Deadbolt (D)

    • Check that the "UP" mark on the deadbolt is facing upwards before inserting it into the hole.
    • DO NOT push the latch out during installation.
    • To change the deadbolt from 60mm to 70mm, twist the barrel clockwise, pull it out, and then twist anti-clockwise to lock into the 70mm position.
  3. Install Front Panel (A)

    • The cable from the front panel goes underneath the deadbolt.
    • Keep the spindle vertical during installation.
  4. Install Mounting Plate (B)

    • The spindle can be cut if necessary for thinner doors.
    • The cable goes through the notch on the lower right part of the mounting plate.
  5. Connect the Cable and Install Back Panel (C)

    • Connect the cable from the front panel to the back panel.
    • Tuck any overlong cable into the door cavity.
    • Keep the knob on the back panel VERTICAL when installing.
  6. Install Batteries and Test the Lock Manually

    • Install four AA Alkaline batteries to power on the lock.
    • After installing batteries, the lock will automatically recognize left or right opening to match the door. You do not need to manually set the left or right opening.
    • Test the lock with a mechanical key to confirm smooth unlocking/locking before using the lock.
    • To access the keyhole, press and rotate the cover clockwise.
    Image showing the emergency USB backup power socket and the two mechanical keys for unlocking.

    Image: Emergency power options including USB backup and mechanical keys.

  7. Mark and Drill Holes for Strike Plate

    Mark the position for the strike plate on the door frame and drill the necessary holes for proper alignment and secure closure.

App Operation Guide

It is important to pair the lock with the Tuya App before using it. In initialization mode, the lock can be unlocked by any fingerprint/card/code.

1. Pair the Lock with Tuya App

  1. Tuya App Installation and Account Registration

    • Scan the QR code below or search for "Tuya Smart" App in Google Play Store or Apple App Store.
    • Install and register a Tuya account using your phone number or email. If you already have an account, simply log in.

    Scan the QR code to download the Tuya Smart App.

  2. Pair the Lock

    • Turn on Bluetooth on your phone.
    • Open the Tuya Smart App, then press any number key on the lock's keypad to activate it.
    • The App will automatically search for and display the device ("2411ATY-F") within about 20 seconds. Click "Add", then "Done" to successfully add the lock. You can rename the lock within the app.
    • Alternatively, you can add the lock manually: Turn on Bluetooth on your phone, open Tuya App, click "Add device", select "Camera & Lock", click the "Lock(BLE)" icon, then "Next". Activate the lock's keyboard, and the App will search and add the lock automatically. Finally, click "Done".

    Note:

    • After successful pairing, you can set fingerprints, cards, and passwords on the Tuya App.
    • If the lock is not found during pairing, reset the lock first (refer to "Reset (System Initialization)" section).
    • Once your phone's App connects the lock, it cannot be linked to other accounts unless disconnected from your App first.

2. Member Management

You can set fingerprints, codes, or cards for yourself or new members. If adding new members, complete their "home information" first.

  1. Set Fingerprint/Card/Passcode for Yourself (Admin)

    Follow these steps: Member Management -> Click "Me" -> Add Fingerprint/Card/Code.

    Warm tips for Fingerprint adding:

    • Record multiple fingerprint angles when setting your fingerprint.
    • Keep your fingers clean and not too dry or wet when using the fingerprint sensor for unlocking.
    Image showing multiple ways to unlock the smart lock: via App, fingerprint, key fob, and passcode.

    Image: Multiple ways to unlock the smart lock.

  2. Set Fingerprint/Card/Passcode for New Members

    After completing home information, you can add new members as Administrator or Common Member in Family Role. If adding an Administrator, they must have a Tuya account. Common members do not require a Tuya account.

    Steps: Member Management -> Select the member -> Add Fingerprint/Card/Code.

    • Card adding: When adding a card or using it for unlocking, place the card on the card sensor area (middle of the number keyboard).
    • Code adding: You should be near the lock with Bluetooth enabled on your phone when setting a passcode. The passcode length is 8-10 digits. After entering the passcode, press '#' to unlock.
  3. Share App Unlock Permissions

    You can share App unlock permissions with others who have a Tuya account. The effectiveness type of the permission can be permanent, single-use, or time-limited. The person who receives this permission can unlock the lock via the Tuya App.

3. More Settings

  • Remote Unlock: Requires a Tuya gateway (purchased separately) and a 2.4GHz WiFi network. This allows remote unlocking via the Tuya App.
  • Remote Voice Unlock: When enabled with a Tuya gateway and WiFi network, you can voice unlock with a Google speaker after code-based verification.
  • Auto Lock: The lock is set to auto-lock by default, automatically locking 5 seconds after unlocking. You can adjust the auto-lock delay time from 5 seconds to 30 minutes. If auto-lock is turned off in the App, the lock enters passage mode and will not lock automatically. You can temporarily close the lock in passage mode by holding the lock icon and sliding to the unlock icon in the App, or by pressing '#' on the lock's keyboard.
  • Lock Volume: There are four grades of volume: High, Normal, Low, and Mute.
  • Secure-lock: A secure-lock switch is located below the knob on the back panel. When enabled, all fingerprint, card, and password unlocks will be invalid. Mechanical keys and App can still be used to unlock.

4. Record

You can view the records of unlocking and setting activities within the App.

Operating Instructions

1. Unlocking the Lock

  • Via Tuya App: Hold the lock icon and slide to the unlock icon in the App. (You need to be near the lock).
  • Via Fingerprint: Place a valid fingerprint on the fingerprint reader.
  • Via Card: Place a valid card on the middle of the lock's keyboard.
  • Via Password: Enter your password and press '#' on the lock's keyboard.
  • Via Unlock/Lock Button: Short press the unlock/lock button.
  • Via Knob: Manually twist the knob on the back panel.
  • Via Key: Open the cover of the keyhole on the front panel, then insert the key to unlock.
Image demonstrating the virtual password anti-snooping feature, where random numbers can be entered before and after the real password.

Image: Virtual password anti-snooping feature.

2. Locking the Lock

The lock is auto-lock by default, automatically locking 5 seconds after unlocking. If auto-lock is turned off, you can quickly close the lock using one of the following methods:

  • Via Tuya App: Hold the lock icon and slide to the lock icon in the App. (You need to be near the lock).
  • Via Keypad: Short press the '#' key on the lock's keyboard.
  • Via Unlock/Lock Button: Short press the unlock/lock button on the back panel.
  • Via Knob: Manually twist the knob on the back panel.
  • Via Key: Open the cover of the keyhole on the front panel, then insert the key to lock.

Maintenance

  • Keep your fingers clean when using the fingerprint sensor to ensure optimal performance.
  • Regularly check the battery level via the Tuya App.
  • Replace all four AA alkaline batteries every 6 months, or when the battery level drops below 30% to avoid lockouts.
  • If the battery is completely dead, use a USB Type-C cable for emergency power or the mechanical key to unlock the door.

Troubleshooting & FAQ

Reset (System Initialization)

If you encounter issues or need to re-pair the lock, you can reset it using one of the following methods:

  1. Method 1: Remove the lock from App (Phone near the lock)

    • Enter the lock's interface on the App.
    • Click the icon in the upper right corner.
    • Click "Remove Device".
    • Click "Disconnect and wipe data".
    • Click "Confirm".
  2. Method 2: Reset by pressing the reset button

    • Remove one of the batteries.
    • Keep pressing the reset button (located on the back panel below the knob) without releasing.
    • Put the battery back in.
    • When you hear four consecutive beeps, release your finger from the reset button. The lock is now initialized.

    Note:

    If you have already paired the lock with the Tuya App and reset it using Method 2, you need to remove the lock from the App before attempting to pair it again.

Frequently Asked Questions

Q: How to add fingerprints?
A: We recommend checking the Quick Installation Guide and following the steps accordingly to complete the setup. For further assistance, contact support@viladepot.com.
Q: How long after should I replace the battery?
A: We recommend replacing the battery after 180 days (ensure batteries are fully charged). Additionally, monitor the battery level weekly via the Tuya App. If the level is less than 30%, replace the batteries promptly.
Q: Fingerprint recognition is not working.
A: If the smart lock has power, try again by changing the angle of your finger. If there is no power, use a spare mechanical key to unlock the door and replace the batteries. If these methods do not resolve the issue, please contact us promptly.

User Tips

  • When setting up fingerprints, try to register your finger from various angles to improve recognition accuracy.
  • Utilize the virtual password anti-snooping feature by entering random numbers before and after your actual passcode to prevent others from guessing it.
  • Regularly check the battery status through the Tuya App to avoid unexpected lockouts.
  • Keep the mechanical keys in a secure, accessible location outside your home for emergency access.

Warranty & Support

Warranty

We provide a 30-day worry-free money-back guarantee and a one-year limited warranty. For any problems or concerns, please feel free to contact us.

Contact Support

E-mail us at: support@viladepot.com

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

Warnings

Please keep an eye on the remaining battery power of the product regularly. We highly recommend that you replace the battery when the product falls below 30% power.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.