SARIK RX26 / RX26B

Contents

SARIK 433MHz RF Wireless Controller Module User Manual

Models: RX26 / RX26B

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your SARIK 433MHz RF Wireless Controller Module. This versatile device is designed for controlling various applications such as LED lighting, Christmas tree lights, and electric motors (forward/reverse), offering convenient wireless control.

SARIK 433MHz RF Wireless Controller Module with two remote controls

Figure 1: Controller Module and Remote Controls

2. Safety Warnings

  • Do NOT disassemble or modify the product. Unauthorized modifications can lead to malfunction, electric shock, or fire.
  • Avoid using in rainy or humid environments. Exposure to moisture can damage the internal components and pose a safety risk.
  • Do NOT place the remote control or module near fire sources or high-temperature areas. Extreme heat can damage the device and its battery.

3. Package Contents

Please check the package for the following items:

  • 1 x 433MHz RF Wireless Controller Module (RX26 or RX26B)
  • 1 or 2 x RF Remote Control(s) (depending on your purchase)

4. Setup and Wiring

4.1. Remote Control Battery Installation

  1. Gently slide open the back cover of the remote control.
  2. Insert the required batteries (typically coin cell batteries, check markings inside) according to the polarity indicators (+/-).
  3. Close the back cover securely.

4.2. Controller Module Wiring

Ensure all power is disconnected before performing any wiring. Refer to the diagrams below for correct connections based on your module model (RX26 or RX26B) and application.

Wiring diagrams for RX26 and RX26B controller modules

Figure 2: RX26 and RX26B Wiring Diagrams

RX26 Module Wiring:

  • IN+: Positive power input (DC 3.6V-30V)
  • IN-: Negative power input
  • OUT+: Positive output to load
  • OUT-: Negative output to load

RX26B Module Wiring:

  • IN+: Positive power input
  • IN-: Negative power input
  • COM: Common terminal for relay output
  • NO: Normally Open terminal for relay output
Pin data table for RX26B module

Figure 3: RX26B Pin Data and Description

Example: Light Control Wiring

Wiring diagram for LED light control

Figure 4: Light Control Wiring Example

5. Operation

5.1. Pairing Procedure

To link your remote control with the receiver module:

  1. Ensure the module is powered on.
  2. Press the learning key (button) on the receiver module according to the desired working mode (see below).
  3. While the LED indicator on the module is in learning state (usually flashing or off), press the desired button on your remote control.
  4. The LED indicator on the receiver board will flash a few times then turn off or on steadily, indicating successful pairing.

5.2. Learning Modes

The module supports three working modes: Momentary, Toggle, and Latching. Choose the mode that best suits your application.

Momentary Mode (Press and Hold)

  • Action: Press the learning key on the receiver once.
  • Procedure: Wait for a moment, the LED will be off, indicating it's in learning state. Push the remote button you wish to use. The LED indicator on the receiver board will flash then come off. After 3 seconds, the LED indicator will be on again, learning successfully.
  • Function: The relay connects while the remote button is pressed and disconnects when released.

Toggle Mode (On/Off with Same Button)

  • Action: Press the learning key on the receiver twice.
  • Procedure: Wait for a moment, the LED will be off, indicating it's in learning state. Press the remote button you wish to use. The LED indicator on the receiver board will flash then come off. After 3 seconds, the LED indicator will be on again, learning successfully.
  • Function: Press the remote button once to connect the relay; press the same button again to disconnect the relay.

Latching Mode (On/Off with Different Buttons)

  • Action: Press the learning key on the receiver three times.
  • Procedure: Wait for a moment, the LED indicator on the receiver board will flash then come off. Press remote button A (for ON). The LED will flash 5 times. Then, press remote button B (for OFF). The LED will flash 5 times. After 3 seconds, the LED indicator will be on again, learning successfully. (Example: Button A = ON, Button B = OFF).
  • Function: Press remote button A to connect the relay; press remote button B to disconnect the relay.

5.3. Clear Code (Reset)

To clear all learned remote controls from the module's memory:

  • Press the learning button on the module 8 times continuously.
  • The light will flash seven times and then go out, indicating all codes have been cleared.

5.4. General Operation

Once paired, operate your connected device by pressing the corresponding button on the remote control. For example, for a door opener, press and hold the

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.