pcbfun CAI-C17

Contents

DIY Electronic Watch Kit with LED Digital Tube Display

Model: CAI-C17 | Brand: PCBFUN

1. Introduction

This manual provides detailed instructions for assembling, operating, and maintaining your PCBFUN DIY Electronic Watch Kit (Model CAI-C17). This kit offers a transparent shell design, showcasing the beauty of electronic art, and features a clear red LED digital display. It's an ultra-lightweight design, comfortable to wear, and available in multiple colors to showcase individual style. Enjoy the fun of creative welding and building your own unique timepiece.

2. Package Contents

Your DIY Electronic Watch Kit includes the following components:

  • 1x PCB (Printed Circuit Board)
  • 1x Microcontroller
  • 1x 0.28-inch Red LED Digital Tube
  • 1x 1,000 ohm Resistor
  • 2x 4.5x4.5x6.5 Momentary Switches (Tact Switches)
  • 1x 32768Hz Crystal Oscillator
  • 1x CR2032 Button Battery Holder
  • 1x 104 Ceramic Capacitor
  • 2x 22P Ceramic Capacitors
  • 4x 1.4x8mm Self-Tapping Screws
  • 1x Transparent Plastic Case (Top Cover)
  • 1x Transparent Plastic Shell (Bottom Cover)
  • 1x Silicone Watch Strap (color may vary)
  • 1x 2mm Cross Screwdriver
Contents of the DIY Electronic Watch Kit
Image: All components included in the DIY Electronic Watch Kit.

3. Specifications

Product Parameters Table
Image: Detailed product parameters.
Product Parameters
Parameter Value
Product Name LED Watch Kit
Shipping Method DIY Kit (loose parts shipping)
Accessory Type Direct insertion component
Display Mode 0.28-inch red LED digital tube
Power Supply 1 CR2032 button battery (not included)
Strap Material Silicone Strap
Case Dimensions 50mm (L) x 45mm (W) x 16mm (Thick)
Strap Size 90mm + 120mm, 20mm wide
Overall Length 260mm
Watch dimensions diagram
Image: Dimensions of the watch components.

4. Setup & Assembly

This is a DIY kit requiring soldering. Please ensure you have basic soldering tools and experience. Follow the steps carefully.

4.1 General Soldering Requirements:

  • Check the quantity and model of all accessories. Use a multimeter to measure components if possible.
  • Follow the tutorial steps provided.
  • Install shorter components first, then taller ones.
  • Install a portion of components, solder them, and then promptly cut off excess pins.
  • Pay attention to welding temperature and time to avoid damaging the circuit board or components.
  • After welding, recheck all solder joints for quality and correct component installation.
  • During power-on debugging, ensure the power supply polarity is correct. The voltage must not exceed 5V.
  • When fixing the shell with screws, tighten them gently and do not overtighten.
Soldering instructions and tips
Image: Important soldering instructions.

4.2 Assembly Steps (Refer to video for visual guide):

Video: LED Watch Installation Tutorial (Model CAI-C17). This video demonstrates the full assembly process.
  1. Install 1,000 ohm Resistor (R1): Insert the resistor into its designated position. There is no positive or negative direction. Solder the pins and cut off any excess.
  2. Install Tact Switches (S1 & S2): Place the two momentary switches into their respective positions. Solder them securely.
  3. Install Single-Chip Microcomputer (U1): Carefully insert the microcomputer chip. Ensure the notch mark on the chip aligns with the direction marked on the circuit board. Solder all pins.
  4. Install Crystal Oscillator (Y1): Insert the crystal oscillator. There is no positive or negative direction. Solder the pins and cut off any excess.
  5. Install 22P Ceramic Capacitors (C1 & C2): Insert the two 22P ceramic capacitors. There is no positive or negative direction. Solder the pins and cut off any excess.
  6. Install 104 Tile Capacitor (C3): Insert the 104 tile capacitor. There is no positive or negative direction. Solder the pins and cut off any excess.
  7. Install Digital Tube (LED1): Insert the digital tube display. Pay attention to the installation direction; the decimal point should be at the bottom. Solder all pins and cut off any excess.
  8. Install Battery Shrapnel (BT1): Place the battery holder shrapnel into its position, ensuring the opening direction is outward. Solder it.
  9. Load Button Battery: Insert one CR2032 button battery into the holder, paying attention to its positive and negative directions.
  10. Assemble Case: Load the assembled circuit board into the transparent upper case cover, then attach the transparent lower case cover.
  11. Secure Case: Fix the case with the provided self-tapping screws. Tighten gently.
  12. Install Watch Strap: Attach the silicone watch strap to the case. Install one side first, then press the spring pin and install it on the other side.
Detailed LED watch installation diagram
Image: Comprehensive diagram of the watch assembly process.

5. Operating Instructions

Operating instructions diagram
Image: Diagram showing operating instructions and circuit principle.
  • Display Time: Press any button (S1 or S2) to display the time. The display will automatically turn off after 10 seconds to conserve battery.
  • Adjust Minutes: Long press and hold button S1 to enter minute adjustment mode. Press S1 repeatedly to cycle through minutes.
  • Adjust Hours: Long press and hold button S2 to enter hour adjustment mode. Press S2 repeatedly to cycle through hours.
  • 24-Hour Format: The display can be set to 24-hour format by shorting the designated solder joints on the back of the PCB.

6. Maintenance

  • Keep the watch clean and dry. Avoid exposure to moisture or extreme temperatures.
  • Handle the watch with care to prevent damage to the transparent case or internal components.
  • If the display dims or stops working, replace the CR2032 button battery.
  • Periodically check the screws on the case to ensure they are snug, but do not overtighten.

7. Troubleshooting

  • Watch not powering on or displaying correctly:
    1. First, verify that the CR2032 button battery is installed correctly with the correct polarity.
    2. Check if the battery has sufficient charge.
    3. Inspect all soldered joints for any short circuits, virtual welding (poor connection), or leakage welding.
    4. Ensure all components are installed in their correct positions and orientations.
    5. Verify that the power supply (if external during debugging) is not reversed and does not exceed 5V.
  • Time not adjusting: Ensure you are long-pressing the correct button (S1 for minutes, S2 for hours) and holding it long enough to enter adjustment mode.

8. User Tips

  • This kit is a great way to learn basic electronics and soldering skills.
  • The 12-hour to 24-hour display option adds versatility.
  • Consider the case size; some users might find it a bit large, but it generally fits well.

9. Warranty & Support

For any issues or support inquiries, please contact the seller directly. Keep your purchase records for reference. This product is intended for educational and hobbyist use, and proper assembly is crucial for its functionality.

10. Important Safety Information

  • Soldering Safety: Always work in a well-ventilated area. Use appropriate safety gear, including safety glasses. Be aware of hot soldering irons and molten solder.
  • Electrical Safety: Ensure correct polarity when installing the battery. Do not exceed the recommended voltage (5V) during testing or operation.
  • Small Parts: This kit contains small parts that could be a choking hazard for young children. Keep out of reach of children under 3 years old.
  • Battery Safety: Use only the specified CR2032 button battery. Do not short-circuit, recharge, or dispose of batteries in fire.

© 2023 PCBFUN. All rights reserved.

For additional guides and documents, please refer to the official PDF: User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.