CNCEST KH-2870YD

Contents

Ultrasonic Plastic Welding Machine

Model: KH-2870YD

Brand: CNCEST

1. Introduction

Thank you for choosing the CNCEST KH-2870YD Ultrasonic Plastic Welding Machine. This device is designed for high-efficiency, strong welding of various plastic materials, textiles, and leather using ultrasonic technology. This manual provides essential information for safe operation, proper setup, and effective maintenance to ensure optimal performance and longevity of your machine.

2. Important Safety Warnings

  • Always wear appropriate personal protective equipment, such as safety goggles, before operating the machine.
  • Ensure that the operator is properly trained in the use of ultrasonic welding machines.
  • Before starting, verify that all cables are correctly connected and the machine is properly earthed to prevent electrical hazards.
  • This machine is designed for welding plastic products (e.g., PP, PVC, PET, ABS) with a thickness generally not exceeding 2 mm.
  • When welding different materials, ensure both parts have similar or identical melting points.
  • DO NOT attempt to weld metal materials. Ensure no metal objects are placed between the welding parts.
  • To prevent burns, avoid touching the welding head during operation.
  • Do not open the machine casing or modify the machine without authorization.
  • If any abnormal situation or noise occurs during welding, immediately stop using the machine.

3. Package Contents

Please check the package carefully to ensure all items are present:

  • 1x Ultrasonic Plastic Welding Machine (Main Unit)
  • 10x Welding Heads (one pre-installed)
  • 1x Welding Handle
  • 1x Power Cord
  • 1x Handle Cord
  • 1x English Manual
Image showing all components included in the package: the main welding machine unit, the welding handle, power and handle cords, and a set of ten welding heads.
Figure 3.1: Included Components

4. Specifications

FeatureSpecification
ModelKH-2870YD
StyleModern
MaterialMetal
Surface TreatmentPlastic Spraying
Plug StandardUS Standard
Power SourceCorded
Voltage110V
Working Frequency28KHz
Power700W
Welding Time0.01-9.99 seconds
Load Persistence (Rated Duty Cycle)10%
Power Cord Length1.5m / 4.92 ft
Handle Cord Length2.8m / 9.18 ft
Weld Head Size / Plastic Welding Area2-12mm / 0.08-0.47 in
Number of Welding Heads10
Product Size (L*W*H)27*14*22cm / 10.63*5.51*8.66 in
Net Weight4.5kg / 9.92 lbs
Diagram showing the dimensions of the ultrasonic welding machine: 22cm (8.66in) height, 14cm (5.51in) width, and 27cm (10.63in) length.
Figure 4.1: Product Dimensions
Rear view of the ultrasonic welding machine, showing the power input, fan, and connection port for the welding handle.
Figure 4.2: Rear Panel Connections

5. Setup Instructions

  1. Unpacking: Carefully remove all components from the packaging. Retain packaging for future storage or transport.
  2. Placement: Place the main unit on a stable, flat, and dry surface. Ensure adequate ventilation around the machine.
  3. Connect Handle: Connect the welding handle cord to the designated port on the rear of the main unit.
  4. Install Welding Head: Select the appropriate welding head for your application and securely attach it to the welding handle. One welding head is pre-installed.
  5. Power Connection: Connect the power cord to the main unit and then plug it into a standard 110V US power outlet. Ensure the machine is properly earthed.
  6. Initial Check: Before turning on, double-check all connections and ensure no metal materials are near the welding area.

6. Operating Instructions

The KH-2870YD features intelligent control for precise welding. Familiarize yourself with the control panel:

Close-up of the ultrasonic welding machine's front control panel, showing the power switch, RUN and ALM indicators, LCD display, TEST and REST buttons, and up/down arrow buttons for setting welding time. Instructions are visible on the panel.
Figure 6.1: Control Panel Overview
  1. Power On: Flip the red POWER switch to the 'ON' position. The LCD screen will illuminate.
  2. Set Welding Time: Use the UP (▲) and DOWN (▼) arrow buttons to adjust the welding time (0.01-9.99 seconds) as required for your material. The LCD displays frequency, current, time, and power.
  3. TEST Function: Press the 'TEST' button to check if the ultrasonic mechanism is functioning correctly. This will activate the ultrasonic output briefly without welding.
  4. Welding Process:
    • Position the two plastic parts to be welded, ensuring they are in close contact. A compression fixture (not included) may be necessary for optimal results.
    • Place the tip of the welding head onto the desired welding spot.
    • Press the button on the ergonomic welding handle to initiate the ultrasonic welding process. The 'RUN' indicator will light up.
    • Hold the button for the set welding time. The machine will automatically stop the ultrasonic output after the duration.
    • Release the button and allow the welded parts to cool slightly before handling.
  5. Alarm (ALM): If the 'ALM' indicator lights up, it signifies an alarm condition. Press the 'REST' button to reset the alarm. Refer to the troubleshooting section for common alarm causes.
  6. Power Off: After use, flip the red POWER switch to the 'OFF' position and unplug the machine from the power outlet.

The machine's high-frequency signal (28KHz) and mechanical vibration ensure instant melting of plastic for strong, flat welds without residual or overflowing glue.

An ultrasonic spot welder in operation, showing a hand holding the welding handle to join two small plastic components.
Figure 6.2: Welding a small plastic piece
An ultrasonic spot welder being used to weld a plastic phone holder component.
Figure 6.3: Welding a phone holder
An ultrasonic spot welder being used to weld the layers of a disposable face mask.
Figure 6.4: Welding a face mask
An ultrasonic spot welder being used to join a leather-like material, demonstrating its versatility.
Figure 6.5: Welding leather-like material

7. Maintenance

  • Cleaning: Regularly clean the exterior of the machine and the welding handle with a soft, dry cloth. Ensure the machine is unplugged before cleaning.
  • Ventilation: Keep the ventilation holes clear of dust and debris to ensure proper heat dissipation by the built-in turbo fan.
  • Welding Heads: Inspect welding heads for wear or damage. Replace worn heads to maintain welding quality.
  • Storage: Store the machine in a dry, dust-free environment when not in use.

8. Troubleshooting

If you encounter issues, refer to the following common problems and solutions:

ProblemPossible CauseSolution
Machine does not power onNo power supply; Power cord looseCheck power outlet; Ensure power cord is securely plugged in
'ALM' indicator lights upOverload protection triggered; Abnormal operationPress 'REST' button to reset. If alarm persists, stop operation and inspect for issues.
Poor welding qualityIncorrect welding time; Improper contact between parts; Worn welding headAdjust welding time; Ensure parts are in close contact, use fixture if needed; Replace welding head
Abnormal noise during operationInternal malfunctionImmediately stop operation, power off, and unplug. Do not attempt to repair yourself.

9. User Tips

  • For consistent welds, always ensure the surfaces to be joined are clean and free of contaminants.
  • Experiment with different welding times on scrap material to find the optimal setting for your specific plastic type and thickness.
  • When welding delicate materials, start with the lowest effective welding time and gradually increase if necessary to avoid damage.
  • Utilize the variety of welding heads provided to match the size and shape of your welding area for better results.

10. Warranty and Support

This product is backed by a standard manufacturer's warranty. For warranty claims, technical support, or service inquiries, please contact your retailer or the manufacturer's customer service department. Please have your model number (KH-2870YD) and purchase information ready when contacting support.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.