NEJE A40640

Contents

NEJE A40640 Diode Laser Module Instruction Manual

Model: A40640 | Brand: NEJE

1. Introduction

This manual provides essential information for the safe and effective use of your NEJE A40640 Diode Laser Module. The A40640 is a high-power laser module designed for precision engraving and cutting across a wide range of materials, featuring Dual-FAC Zoom Technology and integrated air assist. Please read this manual thoroughly before operation to ensure optimal performance and safety.

2. Safety Warnings

WARNING: VISIBLE LASER RADIATION. AVOID EYE OR SKIN EXPOSURE TO DIRECT OR SCATTERED RADIATION.

Laser Class 4 Warning Symbol

Image: Laser Class 4 warning symbol indicating visible laser radiation and the need to avoid eye or skin exposure.

  • Mind The Fire: Always operate the laser in a well-ventilated area and monitor the process to prevent fire hazards.
  • Wear Goggles: Always wear appropriate laser safety goggles (Laser Class 4) to protect your eyes from direct or scattered laser radiation.
  • No Touching: Never touch the laser beam or the laser module directly during operation.
  • Mirror Object: Avoid using the laser on reflective materials without proper precautions, as reflected beams can cause injury.
  • Flammable Materials: Exercise extreme caution when working with flammable materials. Ensure a fire extinguisher is readily available.
  • Harmful Gases: Be aware that some materials (e.g., PVC) may emit harmful gases when processed by the laser. Ensure adequate ventilation and understand the material characteristics before use.
  • Children Safety: Children under 14 years of age are prohibited from using this product. Children over 14 years of age require adult supervision during use.

3. Package Contents

Verify that all items listed below are included in your package:

NEJE A40640 Laser Module Package List

Image: Visual representation of the NEJE A40640 module kit contents.

  • NEJE A40640 Laser Module
  • NEJE Module Manual
  • NEJE Interface Switch / Transfer Board
  • Air Nozzle
  • Screws
  • 4mm PVC Trachea (1m)
  • Connector (M8 to M4)
  • Cable Ties
  • 4-pin (30cm) + 2-pin (30cm) Cables

4. Setup Instructions

  1. Preparation: Before first use, carefully remove all protective films from the laser module and any other components.
  2. Module Connection: Connect the NEJE A40640 laser module to the corresponding interface on your engraving machine's motherboard. Ensure secure connections for all cables.
  3. Adapter Board (if applicable): If using the provided adapter board, refer to the diagram below for proper wiring. The adapter board is used to work with NEJE laser modules. The green box is the output, which connects NEJE laser modules. The red box (Input A/B/C) is the power and signal inputs (you can select one input to use). The yellow box is the Test Button. Press the button, the laser will be on at full power.
Adapter Board Wiring Instructions

Image: Detailed wiring diagram for the adapter board, showing connections for power, TTL signal, and laser module.

Compatibility: The NEJE A40640 module is designed for wide compatibility with most brands of laser engravers, 3D printers, and CNC engravers. It can be directly connected to various control boards or used with dedicated test/switch control boards.

Wide Compatibility Diagram

Image: Diagram illustrating the wide compatibility of the NEJE A40640 module with various control boards and test/switch controls.

For detailed setup procedures and software configuration, please refer to the official NEJE wiki at neje.wiki.

5. Operating Instructions

5.1. Focus Adjustment

The A40640 module features an adjustable focus design, allowing you to optimize the laser for different tasks (engraving or cutting) and material thicknesses. Adjust the focus by rotating the brass knob on the module.

Adjustable Taper Focus Mechanism

Image: Close-up view of the adjustable taper mechanism for focus adjustment on the laser module.

Short, Medium, and Long Focus Settings

Image: Illustration showing the effects of short, medium, and long focus settings on the laser beam for different applications.

  • Short Focus: Best for high-definition engraving, especially on metal.
  • Medium Focus: Provides a balanced effect for general engraving and cutting.
  • Long Focus: Ideal for cutting ultra-thick materials.

You can also adjust the focus directly via low-light mode and block over 95% of light even at full activation using the safety filter lens.

Safety Filter Lens in action

Image: The safety filter lens in operation, demonstrating how it blocks over 95% of laser light for safer focus adjustment.

5.2. Engraving

The A40640 module offers excellent engraving performance with a small focus spot size (0.04x0.06mm) for clear and detailed results.

Comparison of NEJE A40640 focus size vs. others

Image: Comparison showing the smaller, clearer focus of the NEJE A40640 (0.04x0.06mm) compared to other modules (0.08x0.1mm), resulting in sharper engraving.

It supports a wide range of materials including wood, metal, leather, fabric, PCB, glass, ceramics, and vinyl. The dual-focal precision allows for 500DPI high-definition engraving on metals with the short focal end, and uniform results on uneven surfaces with the long focal end.

Examples of materials that can be engraved

Image: A collage showcasing various materials and objects that can be engraved or cut with the NEJE A40640 module, including wood, kraft paper, acrylic, plastic, anodized aluminum, corrugated board, solid wood, veneer, bamboo, MDF, cardboard, stamp rubber, canvas, non-woven fabric, painted metal, painted tile, stone, film-coated transparent acrylic, V2A stainless steel, glass, mirror, 3D wood, leather, grayscale, and EPE.

The module is capable of high-speed engraving, reaching up to 600mm/s for canvas coating, 10000mm/min for wood relief, and 500mm/min for dark stainless steel engraving.

5.3. Cutting

The A40640 module provides powerful cutting capabilities, able to cut up to 20mm thick wood with high verticality and clean edges, often without secondary polishing. For lighter woods like pine, air assist may not even be necessary.

NEJE A40640 cutting 20mm wood with high verticality

Image: Diagram illustrating the NEJE A40640's ability to cut up to 20mm thick wood with high verticality and clean edges, compared to other lasers that may produce carbonized substances and edge errors at 6mm.

NEJE A40640 vs. Others Cutting Comparison

Image: A visual comparison highlighting the NEJE A40640's powerful cutting with fewer burnt marks and high verticality on 8mm basswood (one-pass), versus other lasers that show carbonized substances and edge errors at 6mm.

It achieves high-speed cutting, such as 500mm/min for 3mm basswood (300mm/min for full penetration), and is efficient for MDF (≤6mm), leather (≤3mm), and corrugated cardboard (≤8mm).

A40640 Material and Speed Reference Chart

Image: A chart providing material and speed references for the A40640 module, including settings for wood photo engraving, oak depth engraving, sandalwood depth engraving, painted metal engraving, stainless steel grayscale engraving, leather engraving, 3mm leather cutting, 12mm balsa wood cutting, 3mm basswood cutting, 3mm walnut cutting, 3mm cardboard cutting, 3mm MDF board cutting, 8mm corrugated board cutting, and 3mm black acrylic board cutting.

The built-in air duct assists with smoke exhaust, and an expandable needle tube with a 3D printed nozzle can further improve hard-material cutting performance.

5.4. General Operation Video

Video: A demonstration of the NEJE A40640 laser module in action, performing various cutting and engraving tasks on different materials.

6. Maintenance

  • After Use: Always turn off the device completely after use.
  • Storage: Store the laser module in a dry place, away from dust and moisture. Keep it out of reach of children.
  • Cleaning: Periodically clean the lens and module exterior with a soft, lint-free cloth. Ensure the device is powered off and disconnected before cleaning.
  • Fan Maintenance: The intelligent silent cooling fan is replaceable. Ensure it is free from obstructions for optimal cooling performance.

7. Troubleshooting

  • Laser Not Firing / Weak Output:
    • Check all cable connections, especially the power and TTL signal wires.
    • Ensure the power supply is adequate (e.g., 24V for full power).
    • User Tip: When connecting to the terminal input (with screws), ensure a 24V power supply is connected, and the TTL wire is connected. Crucially, use the original GND of the board for the TTL signal to function correctly; otherwise, the TTL signal may be unstable.
    • Verify software settings for laser power and speed.
    • Check if the lens is clean and free from debris.
  • Poor Engraving/Cutting Quality:
    • Adjust the laser focus for the specific material and task (short for engraving, long for cutting thick materials).
    • Ensure the material is flat and properly secured.
    • Experiment with different speed and power settings for your material.
    • Ensure air assist is properly connected and functioning for cutting, especially on thicker materials.
  • Module Overheating:
    • Ensure the cooling fan is operating correctly and not obstructed.
    • Verify ambient temperature is within operating limits.

8. Specifications

The NEJE A40640 laser module is engineered for high performance and reliability.

NEJE A40640 Laser Module Technical Specifications Table

Image: A table detailing the technical specifications of the NEJE A40640 laser module.

Feature Detail
Product NameNEJE Laser Module
Model NumberA40640
Radiator Size40x50x60mm
Weight204g
Focus MethodZoom focus (adjustable 30-70mm from lens)
ApplicationMetal engraving, thin metal cutting, stone engraving, glass engraving, seal engraving, cardboard cutting, wood etching, canvas engraving, fabric engraving and cutting, leather engraving and cutting, MDF board cutting, plywood cutting, acrylic cutting, etc.
Max Air Pressure1.5mPa
Fan Speed10600RPM (Double ball bearing)
InterfacePH2.0 4pin (+ 2pin 12V extra power - can be free)
Drive DesignBuilt-in
InputDC 12V 4A
Optical PowerPulse 12W+, CW 11W+
Wavelength450nm
Number of Diodes2
Light Source2 x LD +FAC tech
Min Focus Spot Size0.04 x 0.06mm
Temperature FeedbackYES
Power Adjustment MethodPWM duty cycle (3.3V - 24V, 0-20KHz)
Continuously Working (CW)Unlimited
Fan Speed ControlYES
Light FeedbackYES
Warranty2 years (20000h)
Max Cutting & Carving Depth20mm
Cutting Speed (plywood 3mm, with air assist, clear edge)420mm/min 100% power from 1 pass
Stainless Steel Direct Grayscale EngravingYES
Support Stainless Steel GrayscaleYES
Module Size40x50x85 mm
Compatible withNEJE 3 Max, NEJE 3 Pro, NEJE 3 Plus, NEJE 2s Max, NEJE 2s Plus, etc.
Power ControlPWM Power
Modulation FanDouble ball high life fan
DriveNEJE smart quiet drive, built-in static elimination technology.
Surge ProtectionYes
Smart FeedbackYes
Temperature Control45℃
Air Pump RecommendationACO 328+ Air pump, or 30psi+ waterless air pump (used when cutting MDF / leather and higher density materials. Needle type air nozzle supports oily and water-containing air source, and sealed air nozzle can only use clean air pump)
Air Interface4mm PVC trachea

9. User Tips

  • The A40640 module offers significantly higher power (12W with external 24V power supply) compared to older 5.5W modules, allowing for faster and more efficient engraving and cutting.
  • Users have noted the ease with which this module can carve and cut at higher speeds with less power, making it a powerful upgrade.
  • The module typically arrives vacuum-sealed, which helps prevent damage during transit.
  • NEJE is recognized for producing reliable diode cutting equipment and good technology.

10. Warranty and Support

The NEJE A40640 Laser Module comes with a 2-year (20000h) warranty.

For further assistance, detailed tutorials, and troubleshooting guides, please visit the official NEJE service website: neje.wiki.

Manufacturer Information:

  • Manufacturer: Shenzhen Zhi xinjie Technology Co., Ltd.
  • Address: Building 1 Floor 5, ShanKeng Inner Ring Road No.6, ShanKeng Industry Park, ShanXia Village, PingHu Town, LongGang District, ShenZhen City.

EU Authorized Representative:

  • Representative: Prolinx GmbH
  • Address: Brehmstr.56, 40239 Duesseldorf Germany

A PDF version of the user manual is also available for download. You can find it on the product page or at the NEJE service website.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.