HLTNC HL-01

Contents

HL-01 Stepper Motor Driver Controller Board User Manual

1. Product Overview

The HL-01 Stepper Motor Driver Controller Board is a compact and easy-to-use speed control device designed for stepper motors. It supports an input voltage range of 9-24V and adopts simple pulse control technology, enabling precise adjustment of stepper motor speed. This controller is widely applicable to various scenarios that require stable and adjustable motor speed, such as small automation equipment, DIY projects, and precision transmission systems.

With its simple structure, reliable performance, and easy operation, the HL-01 controller provides a convenient solution for stepper motor speed control, suitable for both beginners and professional users.

HL-01 Stepper Motor Driver Controller Board

Figure 1: HL-01 Stepper Motor Driver Controller Board

Various views of the HL-01 controller: front, side, top, and bottom.

Figure 2: Multiple views of the HL-01 controller, showing its compact design from front, side, top, and bottom perspectives.

2. Technical Specifications

ParameterSpecification
ModelHL-01
Brand NameHLTNC
Product TypeStepper Motor Speed Controller Board
Input Voltage9-24V DC
Control ModePulse Control
Speed AdjustmentStepless Speed Regulation
Dissipation Power2A
Working Temperature-10°C - 60°C
Dimension (L×W×H)50×30×15mm (Approx.)
Weight15g (Approx.)
ApplicationMilling Machine, Electric Toy
CertificationCE, NONE

3. Installation Instructions

3.1 Installation Environment

  • Install the controller in a dry, well-ventilated environment, away from high temperature, humidity, dust, and corrosive substances.
  • Place the controller on a flat surface or fix it with screws (screw holes are reserved on the board) to avoid vibration during operation.
  • Ensure there is sufficient space around the controller for heat dissipation, preventing overheating affecting performance.

3.2 Wiring Connection

Before wiring, ensure the power supply is turned off to avoid short circuit or damage to the controller and motor.

  1. Power Connection: Connect the positive pole (+) of the 9-24V DC power supply to the input terminal labeled '+9-24V Input' on the controller, and the negative pole (-) to the 'GND' input terminal. Confirm the wiring is correct to prevent reverse connection.
  2. Motor Connection: Connect the two signal wires of the stepper motor to the 'PUL' and 'DIR' output terminals of the controller (the order can be adjusted according to the motor rotation direction; if the rotation direction is reversed, swap the two wires). The D-/P- and +5V outputs are also available for specific motor driver requirements.
  3. Pulse Control Connection (Optional): If external pulse control is needed, connect the pulse signal source to the 'PUL' output terminal, and the ground wire to the 'GND' output terminal. No connection is required for manual speed adjustment.
Display Interface of the HL-01 controller with labeled components.

Figure 3: HL-01 Controller Display Interface. Key components include GND and +9-24V Input terminals, Reverse button, Potentiometer speed control knob, Forward rotation button, and output terminals for DIR, PUL, D-/P-, +5V, 9-24V Output, and GND.

Wiring Diagram for HL-01 controller with power supply and microstep driver.

Figure 4: Detailed Wiring Diagram. This diagram illustrates how to connect the HL-01 controller to a switching power supply (e.g., 24V) and a Microstep Driver (e.g., DM542) which then connects to a stepper motor. Connections shown include V+, V- from power supply to driver, and from controller: +9-24V input, GND, PUL, DIR, and +5V to the corresponding terminals on the driver.

Video 1: Wiring and Operation Demonstration. This video provides a step-by-step guide on connecting the HL-01 controller to a 24V power supply and a stepper motor driver, followed by a demonstration of speed and direction control.

After wiring, check all connections again to ensure they are tight and correct, and there is no loose or wrong wiring.

4. Operation Steps

  1. Double-check the wiring to confirm the power supply, motor, and (optional) pulse signal are connected correctly.
  2. Turn on the power supply; the power indicator on the controller will light up, indicating the controller is powered on normally.
  3. Speed Adjustment: Rotate the speed adjustment potentiometer on the controller clockwise to increase the motor speed, and counterclockwise to decrease the speed, adjusting to the desired speed according to actual needs.
  4. Direction Control: Use the 'Forward rotation button' and 'Reverse button' on the controller to change the direction of the stepper motor.
  5. Pulse Control (Optional): If using external pulse control, send pulse signals to the 'PUL' terminal; the motor speed will change with the pulse frequency (higher frequency = faster speed, lower frequency = slower speed).
  6. After use, turn off the power supply first, then disconnect the power plug and other connections if necessary.

5. Maintenance

5.1 Daily Maintenance

  • Regularly clean the surface of the controller with a dry cloth to remove dust and debris, avoiding dust accumulation affecting heat dissipation and performance.
  • Check the wiring terminals regularly to ensure they are tight; re-tighten if loose.
  • Avoid touching the controller's circuit board with wet hands or metal objects to prevent short circuit.
  • If the controller is not used for a long time, disconnect all connections and store it in a dry, cool place.

6. Troubleshooting

Trouble PhenomenonPossible CauseSolution
Power indicator not onPower supply failure; wrong wiring; loose terminalsCheck power supply; correct wiring; tighten terminals
Motor does not rotateMotor wiring wrong; speed set to minimum; pulse signal abnormalSwap motor wires; increase speed; check pulse signal
Motor speed unstablePower supply unstable; potentiometer loose; dust on controllerReplace stable power supply; tighten potentiometer; clean controller
Controller overheatsPoor ventilation; input voltage exceeds 24V; long-time overload operationImprove ventilation; adjust input voltage; reduce working time

7. Safety Notes

  • Do not connect the power supply in reverse, which will damage the controller and stepper motor.
  • Do not touch the circuit board or terminals when the controller is powered on to avoid electric shock or burns.
  • The input voltage must be within the range of 9-24V; do not use a power supply exceeding 24V.
  • Do not disassemble, modify, or repair the controller by yourself; contact professional personnel if there is a fault.
  • Keep the controller away from children and pets to avoid accidental injury or equipment damage.

8. Contact Information (Support)

If you have any questions, problems, or suggestions about the HL-01 Stepper Motor Driver Controller Board, please contact our after-sales service for assistance:

  • Email: support@example.com
  • Phone: +86-XXX-XXXXXXX

Update Date: March 2026

9. Application Scenarios

Application scenarios for the HL-01 controller.

Figure 5: The HL-01 controller is suitable for various applications including 3D printing, automated manufacturing lines, textile machinery, and general industrial control systems requiring precise motor speed and direction control.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.