E-ACE K01/K02

Contents

E-ACE Solar Power TPMS Car Tire Pressure Monitoring System

Models: K01 / K02

Brand: E-ACE

1. Introduction

Thank you for purchasing the E-ACE Solar Power Tire Pressure Monitoring System (TPMS). This system is designed to enhance driving safety by providing real-time monitoring of your vehicle's tire pressure and temperature. Upon detecting any abnormal tire conditions, the system will issue an audible warning and display a flashing icon to alert the driver. This proactive warning system helps prevent traffic accidents and ensures the safety of both drivers and passengers.

E-ACE TPMS features: low power consumption, solar charging, USB charging
Key features of the E-ACE TPMS: low power consumption, solar charging, and USB charging.
E-ACE TPMS adapting to various environments: waterproof, anti-stress, shockproof, dust-proof
The E-ACE TPMS is designed to adapt to various environments, being waterproof, anti-stress, shockproof, and dust-proof.

2. Safety Information

Important Reminder:

  • Please read this instruction manual carefully before use.
  • It is not recommended to change the machine parameters unless it is absolutely necessary for special purposes.
  • The schematic diagrams in this manual are for reference only. Always refer to the actual product for specific details.
  • Before installation, ensure the host unit is powered on.
  • When replacing sensor batteries, disassemble and install them one by one. Do not mix or disassemble multiple sensors simultaneously to prevent incorrect placement.

3. Package Contents

The package includes the following items:

E-ACE TPMS package contents including monitor, sensors, tools, and cables
Contents of the E-ACE TPMS package, showing the monitor, external sensors, USB cable, wrench, and backup batteries.
  • TPMS Monitor (Display Unit)
  • External Sensors (4 pcs)
  • USB Charging Cable
  • Anti-theft Nuts (4 pcs)
  • Wrench
  • User Manual
  • Backup Batteries (4 pcs, for external sensors)

4. Specifications

Feature Specification
Brand NameE-ACE
Model NameK01/K02
Item TypeAlarm Systems & Security
MaterialPlastic
Special FeaturesSolar Energy
Voltage5V
Is Batteries IncludedYes
Sensor Battery TypeCR1632
Sensor Working Temperature-30°C to 80°C
Item Weight0.4 kg
Item Height26 cm
Item Width81 cm
Item Length75 cm
Package Length22 cm
Package Width21 cm
Package Height6 cm
Package Weight0.317 kg
OriginMainland China
CertificationRoHS, FCC, ECE, CE, CCC, CC
Product dimensions and interface labels for E-ACE TPMS monitor
Product dimensions and labeled interfaces: Solar Panel, Select, Menu, USB charging interface, Tire Pressure Display, Battery status, Tire Temperature Display, Solar Charging Prompting.

5. Setup and Installation

5.1. External Sensor Installation (Model K01)

For external sensor installation, first ensure the host unit is powered on by pressing and holding the left button. Then, follow these steps:

  1. Screw the anti-theft nut onto the valve nozzle first.
  2. Step 1: Screw in the anti-theft nut first
    Step 1: Screw the anti-theft nut onto the valve stem.
  3. Install the sensor onto the valve according to its designated position (e.g., FL for front left, FR for front right, RL for rear left, RR for rear right) and tighten it.
  4. Step 2: Tighten the sensor onto the valve
    Step 2: Tighten the sensor onto the valve stem.
  5. Screw the anti-theft nut counterclockwise against the sensor until it is snug.
  6. Step 3: Screw the anti-theft nut counterclockwise against the sensor
    Step 3: Screw the anti-theft nut counterclockwise against the sensor.
  7. Use the provided wrench to tighten both the sensor and the anti-theft nut securely.
  8. Step 4: Tighten the sensor and anti-theft nut with a wrench
    Step 4: Use the wrench to securely tighten the sensor and anti-theft nut.
  9. If no pressure is displayed for a corresponding position on the host, reinstall the sensor for that position.

Watch this video for a visual guide on external sensor installation:

Video demonstrating the installation of external tire pressure sensors.

5.2. Built-in Sensor Installation (Model K02)

For built-in sensor installation, first press and hold the left button of the main unit to turn on its power. Then, install the sensor into the tire according to its position, replace the original car valve, and inflate the tires sequentially after installation. Ensure the air is filled when the main unit is turned on.

5.3. Monitor Placement

Apply the adhesive to the bottom of the main unit and place it in a suitable position on the left side of the center console. The product does not require any manual settings or turning on/off after initial setup.

6. Operating Instructions

6.1. Interface and Display Description

E-ACE TPMS display interface with numbered components
Display interface of the TPMS monitor.
  1. Power/Left button
  2. SET button
  3. Right button
  4. Solar energy
  5. Solar icon
  6. Tire pressure units
  7. Tyre temperature
  8. Tire Pressure
  9. Temperature unit
  10. Battery status
  11. Clock (if applicable to model)

6.2. Button Function Description

  • USB Port: Used for charging the receiver unit.
  • Power/Left Button:
    • Short press (standby mode): Adjust brightness.
    • Long press: Turn the unit on/off.
    • Left switch (menu mode): Navigate left or switch menu options.
  • Right Button:
    • Short press (standby mode): Adjust brightness.
    • Long press: Turn off alarm.
    • Right switch (menu mode): Navigate right or switch menu options.
  • SET Button (M Menu/Confirm Button):
    • Long press (standby mode): Enter menu mode.
    • Short press (menu mode): Select the parameter to be adjusted and confirm.

6.3. Basic Functions of the Product

  • The factory default tire pressure unit is BAR, the temperature unit is °C.
  • The default upper limit for tire pressure is 3.2 bar, and the lower limit is 1.8 bar.
  • The default temperature alarm value is 68°C.
  • The backlight brightness automatically adjusts based on ambient light intensity. It can also be manually adjusted using the left and right buttons.

6.4. Unit Setting (Factory Default: Bar, °C)

In standby mode, press and hold the SET button for 3 seconds to enter the system setting state. The Bar icon will appear in the lower left corner. Press the SET button again to enter the operable setting state. Use the Left and Right buttons to select between Psi or Bar units. Once the desired unit is identified, press the SET button to complete the setting.

To set the temperature unit, long press the SET button for 3 seconds to enter the system setting state. Press the Right button once to navigate to the temperature unit setting. Press the SET button to enter the operable setting state. Use the Left and Right buttons to select between °C or °F. Once the desired unit is selected, press the SET button to complete the setting.

Display showing unit setting options for Bar and Psi
Display showing options for pressure units (Bar and Psi).

6.5. Time Setting (For models with clock function only)

In standby mode, long press the SET button for 3 seconds to enter the system setting state. Press the Right button twice to enter the time setting. Short press the SET button twice; the hour number will flash. Use the Left and Right buttons to adjust the hours. After setting the hours, short press the SET button to set the minutes. Adjust the minutes with the Left and Right buttons. Long press the SET button to exit the setting once the time is complete.

Display showing time setting interface
Display showing the time setting interface.

6.6. Adjusting Tire Pressure Limits

In standby mode, press and hold the SET button for 3 seconds to enter the system setting state. Press the Right button twice to enter the maximum air pressure setting. Press the SET button once; the air pressure number will flash. Use the Left and Right buttons to set the maximum air pressure. After setting, press and hold the SET button to exit.

To set the lower limit, press and hold the SET button for 3 seconds to enter the system setting state. Press the Right button three times to enter the lower limit setting. Press the SET button once; the barometric pressure number will flash. Use the Left and Right buttons to set the lower limit parameter value. After setting, press and hold the SET button to exit.

Display showing tire pressure limit settings
Display showing tire pressure limit settings (e.g., 3.2 Bar for high, 1.8 Bar for low).

6.7. Adjusting Temperature Limits

In standby mode, press and hold the SET button for 3 seconds to enter the system setting state. Press the Right button four times to enter the tire temperature upper limit setting. Short press the SET button once; the tire temperature number will flash. Use the Left and Right buttons to set the highest upper limit tire temperature. After the setting is completed, long press the SET button to exit.

Display showing temperature limit settings
Display showing temperature limit settings (e.g., 68°C).

7. Maintenance

7.1. Replacing Sensor Battery

When replacing the battery of an external sensor (CR1632, working temperature -30°C to 80°C), please follow these steps carefully, replacing one sensor at a time to avoid mixing them up:

  1. Before disassembling, prepare a nut wrench. Turn the nut clockwise to separate it from the sensor, then remove the sensor counterclockwise.
  2. Use a wrench to unscrew the upper cover of the sensor in a counterclockwise direction.
  3. Step 1: Open the outer cover of the sensor with a wrench
    Step 1: Open the outer cover of the sensor using the provided wrench.
  4. Take out the old battery from the battery holder. Dispose of the old battery responsibly according to environmental protection guidelines.
  5. Distinguish the positive and negative positions (positive '+' facing upwards) and install a new CR1632 lithium battery.
  6. Step 2: Remove the original battery and install a new one
    Step 2: Remove the old battery and insert a new CR1632 battery, ensuring correct polarity.
  7. Screw on the upper cover of the sensor, and then use a wrench to tighten it clockwise.
  8. Step 3: Close the upper cover and tighten with a wrench
    Step 3: Close the upper cover and tighten it securely with the wrench.

Watch this video for a visual guide on sensor battery replacement:

Video demonstrating how to replace the battery in an external sensor.

7.2. Single Sensor Replacement

To replace a single sensor, first remove the faulty sensor and install the new one. In standby mode, long press the SET button for 3 seconds to enter the system setting state. Press the Right button five times to enter the pairing selection mode. Press the SET button once; the '0' on the interface will flash, indicating the default front left wheel. Use the Left and Right buttons to select the position of the sensor to be replaced (0=front left, 1=front right, 2=rear left, 3=rear right). After selecting the position, press the SET button to make the number flash. Install the new sensor on the tire and check if the number changes. Once a change is observed, long press the SET button to exit.

  • Note for Built-in Sensors: If replacing a built-in sensor, inflate and deflate the tire when the number below flashes.
  • During this pairing process, any sensor can be matched to any position.
Display showing sensor pairing selection mode
Display in sensor pairing selection mode.

7.3. Restore Factory Settings (Re-pairing)

In the power-on state, press and hold the SET button for 3 seconds to enter the settings. Press the Left button again to navigate to item 7, then press the SET button twice to reset the machine and restore factory settings. The system will then search for sensors again. To update the sensors, install the new sensors on the valves in order, or drive the car at a speed of 30 km/h or more after resetting. After driving for approximately 10-30 minutes, the host will automatically search for sensor signals. Once all four sensors are found, the pairing is complete. After restoring factory settings, any previously manually set data will revert to factory defaults.

Display showing factory reset confirmation
Display confirming factory reset.

8. Troubleshooting

  • No pressure displayed for a specific tire: If a tire position on the monitor shows no pressure, try reinstalling the sensor for that position.
  • Settings not saving: If you enter the system setting state (long press SET button for 3 seconds) and make changes, but the settings are not saved, ensure you confirm the changes with a short press of the SET button before the system automatically exits after 30 seconds of inactivity.
  • Built-in sensor not registering after replacement: If replacing a built-in sensor and the display is flashing, inflate and deflate the tire to help the sensor register.
  • Sensor pairing issues: During the pairing process, any sensor can be matched to any position. If issues persist, try restoring factory settings and re-pairing all sensors.

9. User Tips

  • Quick Installation: Many users find the system easy to install and pair within minutes, often arriving almost fully charged.
  • Early Leak Detection: The system is effective at quantifying even subtle air leaks, allowing you to address issues before they become critical.
  • Sensor Size: External tire caps might be larger than expected, but they secure firmly once installed.
  • Display Update: The display typically shows tire pressure and temperature readings within a few minutes of installation or driving.
  • Automatic Operation: The system often features an automatic shut-off when the car is parked, and automatic start-up when driving.
  • Charging Flexibility: While solar charging is convenient, the USB-C port provides an alternative charging method, especially useful in low-light conditions.
  • Initial Synchronization: Allow at least 3 minutes for the sensors to synchronize with the monitor after installation or re-pairing.

10. Warranty and Support

E-ACE products are designed for reliability and performance. For any technical support or warranty inquiries, please contact us using the information below. Please note that this product comes with a 365-day free replacement policy for defects.

For user manuals in multiple languages, please refer to the official PDF document: E-ACE Solar Tire Pressure Monitoring System User Manuals (PDF)

Contact Information:

  • Website: www.e-ace.cn
  • Email: fireking@e-ace.cn
  • Phone: +86 0755-8464 4084
  • WhatsApp: +86-18127083357
  • Address: Floor 2nd, No.1 Yuanxia street, Pingshan District, Shenzhen City, Guangdong Province, 518000, China

11. Compliance

This product complies with relevant safety and quality standards. Certifications include:

  • RoHS
  • FCC
  • ECE
  • CE
  • CCC
  • CC

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.