1. Safety Information & Setup
Please read all instructions carefully before installation and use.
- The power cord is for use in dry locations only.
- Any modification to the product must be performed under the guidance of a professional electrician. The manufacturer is not responsible for damage caused by modified products.
- Ensure the power supply is disconnected before installation or modification.
Installation Guidelines
- Prepare Surface: Ensure the mounting surface is clean, dry, and smooth for optimal adhesion of the strip's double-sided tape.
- Measure and Cut: Measure the desired length. The LED strip is cuttable at each LED bead, indicated by a cut mark. Each segment is approximately 8mm. Cut only along these designated marks.
Image 1.1: LED strip illustrating individual LED cut points and the 8mm strip width. Each LED can be cut, offering flexible installation.
- Power Connection:
- 5M LED Strip: Powered from one end. The package includes a 2-pin wire at one end for connection to a 12V DC power supply (transformer not included).
- 10M LED Strip: Should be powered from both ends to reduce voltage drop and ensure uniform brightness. The package includes 2-pin wires at both ends for this purpose.
- Adhere Strip: Peel off the backing from the double-sided adhesive tape and carefully press the LED strip onto the prepared surface.
- Connect Power: Connect the 2-pin wire(s) to a compatible 12V DC power supply. Ensure correct polarity (+ to + and - to -).
Image 1.2: Power connection diagram for 5M and 10M LED strips. 5M strips are powered from one end, while 10M strips require power from both ends to prevent voltage drop.
2. Operating Instructions
Once properly installed and connected to a 12V DC power supply, the LED strip will illuminate. The strip offers different color temperatures to suit various ambiance needs.
Color Temperature Options
- 3000K Warm White: Provides a cozy, inviting, yellowish light, ideal for bedrooms and living rooms.
- 4000K Natural White: A balanced, neutral white light, suitable for kitchens, offices, and general task lighting.
- 6000K White (Cool White): A bright, crisp white light, often used for modern aesthetics or areas requiring high visibility.
Image 2.1: Visual representation of the three available color temperatures (3000K, 4000K, 6500K) as applied in a typical room setting.
Product Demonstration
Video 2.1: A short demonstration showcasing the flexibility and illumination of the LED strip in various color temperatures.
3. Maintenance
- Cleaning: Gently wipe the LED strip with a dry, soft cloth if it accumulates dust. Do not use liquid cleaners or abrasive materials.
- Environment: As this product is IP20 non-waterproof, ensure it is used only in dry indoor environments. Avoid exposure to moisture, humidity, or direct water contact.
- Handling: Avoid excessive bending or sharp folds, especially near the LED components, as this can damage the strip's internal circuitry.
4. Troubleshooting
- LED Strip Does Not Light Up:
- Check if the 12V DC power supply is properly connected and functioning.
- Verify the polarity of the connection (+ to + and - to -).
- Inspect the strip for any visible damage or breaks, especially at cut points or bends.
- LED Strip is Dim or Unevenly Lit:
- Ensure the power supply is adequate for the length of the strip.
- For 10M strips, confirm that both ends are powered to mitigate voltage drop.
- Check for loose connections.
- Flickering LEDs:
- Ensure a stable power supply.
- Check for any loose wiring or connections.
5. Specifications
| Feature | Specification |
|---|---|
| Type | SMD 2835 LED Strip Light |
| Input Voltage | DC 12V |
| Nominal Voltage | 12 V |
| Power Source | DC |
| LED Type | SMD 2835 |
| LEDs Number/M | 120 LEDs/meter |
| LED Chip Brand | Epistar |
| FPCB Width | 8mm |
| Emitted Colour | 3000K Warm White, 4000K Natural White, 6000K White |
| Color Rendering Index (CRI) | RA90 |
| Lumen | 24-26lm/LED |
| Luminous Flux | 2000-82000 (unit not specified, typically Lumens) |
| Power Consumption | 25-30W/5Meters; 50-60W/10Meters |
| Length Options | 5 meters, 10 meters (per roll) |
| Cuttable | Each LED can be cut at marked points |
| Waterproof Grade | IP20 Non-waterproof (Indoor use only) |
| Working Temperature | -20°C to 50°C |
| Average Life (hrs) | 50,000+ hours |
| Certification | CE, RoHS |
| Adhesive | Double-sided Tape (pre-applied) |
| Occasion | Living room (suitable for various indoor decorative lighting) |
6. User Tips
- Surface Preparation: For best adhesion, thoroughly clean the mounting surface with isopropyl alcohol and let it dry completely before applying the LED strip.
- Planning Cuts: Always plan your layout and mark cut points before making any cuts to avoid waste.
- Power Supply Matching: Ensure your 12V DC power supply has sufficient wattage to power the entire length of your LED strip.
7. Warranty & Support
For specific warranty terms, technical support, or any product-related inquiries, please contact the seller directly through your purchase platform. Keep your order details handy for faster assistance.