TEKIVI 6839C

Contents

TEKIVI 6839C Intelligent Electricity Meter User Manual

DC 8-100V High Precision LCD Digital Display Voltage Electricity Indicator with Temperature Display

1. Product Overview

The TEKIVI 6839C is a high-precision LCD digital display voltage and electricity indicator designed for universal use with ternary lithium, lithium iron, and lead-acid batteries. It provides real-time voltage, battery percentage, and temperature readings, making it an essential tool for monitoring battery status in various applications.

TEKIVI 6839C Intelligent Electricity Meter displaying voltage, percentage, and temperature

Figure 1: Front view of the TEKIVI 6839C meter displaying voltage, battery percentage, and temperature.

This meter features a high-definition color screen with a wide viewing angle for clear visibility. It is suitable for a wide range of DC voltage systems from 8V to 100V.

2. Specifications

2.1. Product Parameters

  • Voltage Measurement Range: DC 8 - 100V
  • Operating Current: ≤ 20mA
  • Screen Type: Color LCD (wide viewing angle)
  • Detection Accuracy: ± 1%
  • Scan Speed: 1 scan/500ms
  • Static Power Consumption: < 2mA

2.2. General Specifications

  • DIY Supplies: Electrical
  • Power Supply: DC
  • Display Type: Digital Only
  • Battery Included: No
  • High-concerned chemical: None
  • Origin: Mainland China

3. Setup and Installation

3.1. Package Contents

  • TEKIVI 6839C Intelligent Electricity Meter
  • Connecting Wires (pre-attached)

3.2. Wiring Instructions

The meter comes with two pre-attached wires for connection to your battery system:

  • Red Wire: Connect to the positive (+) terminal of your DC power source/battery.
  • Black Wire: Connect to the negative (-) terminal of your DC power source/battery.

Caution: Ensure correct polarity when connecting the wires to avoid damage to the device or battery system. Disconnect power before making any connections.

TEKIVI 6839C meter with red and black connecting wires

Figure 2: Rear view of the meter showing the connecting wires.

3.3. Mounting

The meter can be integrated into a panel or mounted in a suitable location. Refer to the dimensional drawings in Section 8 for precise cutout requirements if panel mounting.

4. Operating Instructions

4.1. Basic Operation

  • Power On/Off: On the home page, short-press the power button (usually the single button on the right side) to turn the display on and off.
  • Entering Setup Mode: Press and hold the SET button (the same single button) for 2 seconds to enter the setup mode.

4.2. Mode Setting Instructions

Once in setup mode, you can navigate through various menus to configure the meter for your specific battery type and preferences.

4.2.1. Ternary Lithium Battery Settings (Menu 1)

  1. From the main page, press and hold the button for 2 seconds to enter settings. The display will show "L-003" (default for 3 strings).
  2. On the "L-003" page, press and hold the button for 2 seconds; the value "03" will flash.
  3. Short-press the button to select the number of battery strings (from 03 to 22 strings).
  4. After selecting, press and hold the button for 2 seconds to confirm (the value will become solid).
  5. Press and hold the button for 2 seconds again to return to the main page (settings complete), or short-press to go to the next settings page.
Illustrative image of the TEKIVI 6839C meter

Figure 3: Ternary Lithium Battery Setting (L-mode). (Illustrative product image)

4.2.2. Iron-Lithium Battery Settings (Menu 2)

  1. From the main page, press and hold the button for 2 seconds to enter settings. Short-press the button to switch to the "F-003" page (default for 3 strings).
  2. On the "F-003" page, press and hold the button for 2 seconds; the value "03" will flash.
  3. Short-press the button to select the number of battery strings (from 03 to 26 strings).
  4. After selecting, press and hold the button for 2 seconds to confirm (the value will become solid).
  5. Press and hold the button for 2 seconds again to return to the main page (settings complete), or short-press to go to the next settings page.
Illustrative image of the TEKIVI 6839C meter

Figure 4: Iron-Lithium Battery Setting (F-mode). (Illustrative product image)

4.2.3. Lead-Acid Battery Settings (Menu 3)

  1. From the main page, press and hold the button for 2 seconds to enter settings. Short-press the button to switch to the "P-12" page (default for 12V).
  2. On the "P-12" page, press and hold the button for 2 seconds; the value "12" will flash.
  3. Short-press the button to select the battery voltage (12V, 24V, 36V, 48V, 60V, 72V, 84V).
  4. After selecting, press and hold the button for 2 seconds to confirm (the value will become solid).
  5. Press and hold the button for 2 seconds again to return to the main page (settings complete), or short-press to go to the next settings page.
Illustrative image of the TEKIVI 6839C meter

Figure 5: Lead-Acid Battery Setting (P-mode). (Illustrative product image)

4.2.4. Custom Voltage Settings (Menu 4)

This mode allows setting custom high and low voltage thresholds (DC 8V to 100V) with power-off memory.

  1. From the main page, press and hold the button for 2 seconds to enter settings. Short-press the button to switch to the custom voltage setting page (display shows "VOL: 88.8V C-" and "88.8"). The top row is high voltage, bottom row is low voltage.
  2. Press and hold the button for 2 seconds; the first value (high voltage) will flash.
  3. Short-press the button to select the desired high voltage value.
  4. Press and hold the button for 2 seconds again; the high voltage value will become solid, and the second value (low voltage) will flash.
  5. Short-press the button to select the desired low voltage value.
  6. After setting both values, short-press the button to confirm and enter the next settings page, or press and hold for 2 seconds to return to the main page.
Illustrative image of the TEKIVI 6839C meter

Figure 6: Custom Voltage Setting (C-mode). (Illustrative product image)

4.2.5. Backlight Settings (Menu 5)

The factory default backlight is always on.

  1. From the main page, press and hold the button for 2 seconds to enter settings. Short-press the button to switch to the "bL" page (display shows "00 SET bL").
  2. Press and hold the button for 2 seconds; "00" will flash.
  3. Short-press the button to select backlight duration: "00" (always on), 10, 20, 30, 40, 50, 60, 70, 80, or 90 seconds.
  4. After selecting, press and hold the button for 2 seconds to confirm (the value will become solid).
  5. Press and hold the button for 2 seconds again to return to the main page (settings complete), or short-press to go to the next settings page.
Illustrative image of the TEKIVI 6839C meter

Figure 7: Backlight Setting (bL-mode). (Illustrative product image)

4.2.6. High and Low Pressure Alarm Settings (Menu 6)

Configurable high and low voltage alarms.

  1. From the main page, press and hold the button for 2 seconds to enter settings. Short-press the button to switch to the alarm settings page (display shows "VOL: 88.8V AL" and "88.8"). The top row is high pressure (voltage), bottom row is low pressure (voltage).
  2. Press and hold the button for 2 seconds; the first value (high voltage alarm) will flash.
  3. Short-press the button to select the desired high voltage alarm value.
  4. Press and hold the button for 2 seconds again; the high voltage alarm value will become solid, and the second value (low voltage alarm) will flash.
  5. Short-press the button to select the desired low voltage alarm value.
  6. After setting both values, short-press the button to confirm and enter the next settings page, or press and hold for 2 seconds to return to the main page.
Illustrative image of the TEKIVI 6839C meter

Figure 8: High and Low Pressure Alarm Setting (AL-mode). (Illustrative product image)

4.2.7. Voltage Calibration Setting (Menu 7)

Important: This product is factory-calibrated. Non-professionals should NOT use this function. Unauthorized operation will affect voltage accuracy. Contact the manufacturer if calibration is required.

  1. From the main page, press and hold the button for 2 seconds to enter settings. Short-press the button to switch to the electronic calibration function page ("CL").
  2. On the "CL" page, press and hold the button for 2 seconds; the displayed voltage will flash.
  3. Press and hold the button for 2 seconds again to complete automatic calibration and return to the main page. Calibration is complete.
Illustrative image of the TEKIVI 6839C meter

Figure 9: Voltage Calibration Setting (CL-mode). (Illustrative product image)

4.2.8. SOC Mode Setting (Menu 8)

Important: Users cannot set this function. Please contact the manufacturer for SOC mode configuration.

  1. From the main page, press and hold the button for 2 seconds to enter settings. Short-press the button to switch to the SOC settings page ("So").
  2. On the "So" page, press and hold the button for 2 seconds. Select "ON" or "OF" (OFF) on the right.
  3. Press and hold the button for 2 seconds to confirm.
  4. Press and hold the button for 2 seconds again to return to the main page (settings complete), or short-press to go to the next settings page.
Illustrative image of the TEKIVI 6839C meter

Figure 10: SOC Mode Setting (So-mode) - OFF. (Illustrative product image)

Illustrative image of the TEKIVI 6839C meter

Figure 11: SOC Mode Setting (So-mode) - ON. (Illustrative product image)

4.2.9. Restore Factory Settings (Menu 9)

Important: Non-professionals should NOT use this function, as it will restore all product parameters to factory defaults and may affect product use.

  1. From the main page, press and hold the button for 2 seconds to enter settings. Short-press the button to select the factory reset page ("rF").
  2. On the "rF" page, press and hold the button for 2 seconds. The three "8"s on the left will flash, then turn into three "0"s.
  3. Press and hold the button for 2 seconds to restore factory settings. The three "0"s will light up steadily, indicating the factory reset is complete.
  4. Press and hold the button for 2 seconds to return to the main page (settings complete), or short-press to go to the next settings page (Menu 1).
Illustrative image of the TEKIVI 6839C meter

Figure 12: Factory Reset Setting (rF-mode). (Illustrative product image)

5. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the display and casing. Do not use abrasive cleaners or solvents.
  • Environmental Conditions: Avoid exposing the device to extreme temperatures, direct sunlight, high humidity, or corrosive environments.
  • Connections: Periodically check wiring connections to ensure they are secure and free from corrosion.

6. Troubleshooting

ProblemPossible CauseSolution
No display/Device not powering onIncorrect wiring polarity, loose connections, power source outside voltage range, device fault.Check red wire to positive, black wire to negative. Ensure connections are secure. Verify battery voltage is within 8-100V DC.
Incorrect voltage/percentage readingIncorrect battery type/string setting, device fault.Verify the meter is configured for the correct battery type (Ternary Lithium, Iron-Lithium, Lead-Acid) and number of strings/voltage. Avoid voltage calibration unless you are a professional.
Display flickering or unstableUnstable power supply, loose connection.Ensure power supply is stable. Check all wiring connections for tightness.

7. User Tips

  • Simple Installation: Users have noted the ease of installation. Ensure correct polarity for quick setup.
  • Clear Display: The meter provides a clear and accurate display of charge level, voltage, and temperature.
  • Compact Size: The device is surprisingly small, which can be beneficial for space-constrained applications. Handle with care during installation.

8. Dimensional Drawings

Below are the precise dimensions of the TEKIVI 6839C Intelligent Electricity Meter for mounting and integration purposes.

Dimensional drawing of TEKIVI 6839C meter with measurements

Figure 13: Dimensional drawing of the 6839C meter. Dimensions: 68.78mm (Length) x 38.8mm (Width) x 14.3mm (Height).

9. Product Video

Watch this video for a visual overview of the TEKIVI 6839C Intelligent Electricity Meter.

Video 1: TEKIVI 6839C Product Showcase.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your original point of purchase or the manufacturer directly. Please refer to the official user manual PDF for additional details: TEKIVI 6839C User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.