Introduction
This manual provides instructions for the safe and efficient operation of your NOPARDE HT 4-Image Switchable Projection Lamp. This versatile projector is designed for various applications, including home parties, outdoor events, and advertising displays, featuring easy-to-switch patterns and robust construction.
Safety Precautions
General Safety Guidelines
- Lamps not rated as waterproof should not be installed in rain-exposed areas. Damage from rain in such installations is not covered by warranty.
- If any issues arise, contact customer service. Do not attempt to disassemble the lamps yourself, as this will void the warranty.
- For waterproof lamps, ensure the "waterproof fixing iron ring" is tightened. Failure to do so may allow water to penetrate the lens over time, affecting projection quality.
Electrical Safety
- For wiring, you can cut off the plug and connect the two main wires. The red wire is positive, and the blue wire is negative. If a ground wire is present, connect it appropriately.
Product Overview
Key Features
- 4-Image Switchable Feature: One luminaire can project 4 patterns in rotation.
- New Optical Lens: +20% light transmittance for uniform brightness and higher clarity.
- Multiple Heat Dissipation: IP68 waterproof dual fan heat dissipation and cold-forged radiator for safe operation.
- Waterproof Design: All-in-one IP68 waterproof design, suitable for working environments from -40°C to 60°C.
- DMX512 Synchronous Linkage: Supports DMX512 control protocol for synchronized projection across multiple units.
- Remote Control: Convenient remote control for pattern switching, time customization, and speed customization.
- Adjustable Bracket: Support adjustable by 180°, base adjustable by 360°.
- Included Bulbs and Batteries: Ready to use out of the box.
- Certified Safety: CE and RoHS certified.
Components
The projector includes the main unit, a remote control, and several screws for installation.


Setup
Installation Methods
The projector can be installed in various ways:

Adjusting Projection Angle

Lens Selection (Optional)

Operating Instructions
Powering On
Plug in the power switch. The light will not turn on immediately; there is a 5-7 second delay for the pattern to automatically repeat. Wait until the light is on before using the remote control.

Remote Control Functions

- ON: Turns the light fixture on.
- OFF: Turns the lamp off.
- 图1 (Figure 1): Resets to the first pattern.
- 下图 (Next Pattern): Switches to the next pattern.
- 5S: Changes pattern every 5 seconds.
- 10S: Changes pattern every 10 seconds.
- 15S: Changes pattern every 15 seconds.
- 30S: Changes pattern every 30 seconds.
Adjusting Projection Clarity
After the light is on, adjust the clarity by twisting the lens slowly. Continue twisting until the pattern is clear. Be careful not to drop the lens.
Suggestion: Test indoors first, then install. After installation, fine-tune the lens for optimal clarity.
Note: Different projection distances require readjustment. Avoid debugging outdoors during the day. Before adjusting the angle, loosen the bracket, adjust the angle, then tighten it.

Pattern Switching
The projector supports 4 patterns in rotation. Use the remote control to switch between patterns or set a timed interval.

DMX512 Synchronous Linkage
The projector supports DMX512 control protocol, allowing multiple units to be synchronized. Set up one lamp as a host, and other lamps will synchronize with it.

Maintenance
Replacing Projection Gobbos (Light Sheets)
- Step 1: Turn off power. When replacing the lamp, always turn off the power first.
- Step 2: Allow to cool. After the lamp is powered off, the temperature on the lamp is high. Wait for it to cool before replacing the lamp.
- Step 3: Remove front cover. Remove the screws and take off the front cover/bezel.
- Step 4: Place light sheet. Place the new light sheet face down, ensuring the black side of the lamp faces outward.
- Step 5: Secure light sheet. Use the fixing ring (iron wire) to fix the light piece.
- Step 6: Reattach front cover. Use the screws to fix the front cover of the lamp.

Cleaning
Regularly clean the lens and exterior of the projector with a soft, dry cloth to maintain optimal projection clarity and prevent dust buildup. Ensure the device is powered off and unplugged before cleaning.
Troubleshooting
Common Issues and Solutions
| Problem | Possible Cause | Solution |
|---|---|---|
| No projection / Lamp not turning on | No power, loose connection, lamp not cooled down after previous use. | Check power connection. Ensure lamp has cooled down if recently used. Wait 5-7 seconds after powering on for the pattern to appear. |
| Projection is blurry | Lens not focused correctly, incorrect lens for distance. | Adjust the lens by twisting until the image is clear. Consider using an optional lens suitable for your projection distance. |
| Pattern not switching | Remote control issue, internal mechanism issue. | Check remote control batteries. Ensure line of sight to the projector. If problem persists, contact customer service. |
| Water penetration | Waterproof fixing iron ring not tightened (for waterproof models). | Ensure the waterproof fixing iron ring is securely tightened. If water has already penetrated, contact customer service. |
When to Contact Customer Service
If you encounter any problems that cannot be resolved using the troubleshooting steps above, or if you suspect a malfunction, please contact customer service. Do not attempt to disassemble or repair the unit yourself, as this will void the warranty.
Specifications
| Parameter | Value |
|---|---|
| Product Name | Projection lamp |
| Product Number | XZHT-35-70W |
| Brand Name | NOPARDE |
| Model Number | HT |
| Item Type | Advertising Light |
| Installation Method | Self-contained |
| Use | For advertising |
| Origin | Mainland China |
| Is Bulbs Included | Yes |
| Power Source | AC |
| Voltage | AC100-240V |
| Input Power | 15-105W (depending on wattage variant) |
| Operating Voltage | DC24-36V |
| Power | 40-300W (depending on wattage variant) |
| Luminous Flux | 2000-82000 LM |
| Waterproof Level | IP68 (working environment -40°C to 60°C) |
| Life | ≥50000h |
| Weight | 2-7.5kg |
| Color Temperature | 8000K-8500K |
| Appearance Color | Black |
| Heat Dissipation | Fan |
| Lamp Diameter | 37mm / High Power 63MM |
| Fittings | Several screws |
| Certification | CE, RoHS |
| High-concerned chemical | None |
Product Dimensions

User Tips
- Lens Variety: Consider purchasing additional lenses if you need to project at different distances or desire varying image sizes. The standard 0.33 lens is versatile, but other options (0.2, 0.5, 0.65) are available for specific needs.
- Pattern Customization: Explore custom lighting solutions by contacting customer service for scheme design, budget quotation, and installation guidance.
- Indoor Testing: Always test the projector indoors to adjust clarity and focus before permanent outdoor installation.
Warranty and Support
Warranty Information
This product comes with a warranty. Please refer to the "WARRANTY CARD" provided with your product for details on maintenance date, reason, and personnel.
Important: The warranty does not cover damages resulting from installation in rain-exposed areas for non-waterproof lamps, or self-disassembly.
Customer Support
For any issues or inquiries, please contact customer service.
A detailed user manual in PDF format is available for download: User Manual (PDF).
Video Demonstrations
Product Demonstration Video
This video demonstrates the 4-pattern rotating projection feature of the lamp, showcasing various "Happy New Year!" designs.
Product Features Overview
This video provides an overview of the projector's user-friendly features, energy efficiency, certified safety, versatile projection capability, and self-contained design.